Installation guide

ManualsBrandsJenn-Air ManualsCooktopCVGX2423B

EXPRESSIONS

GAS COOKTOP

mmmJENN.AIR

408 WEST FOURTHSTREET,NORTH• NEWTON,IA 50208

IMPORTANT: Installation should be performed only by a Jenn-Air Authorized Servicer or other qualified installer. Read safety

precautions in the Use & Care Manual before using this appliance.

(Dimensions shown in both inches and centimeters.)

GAS CONNECTION

AXIS

FLOOR

EXHAUST I

OPTION

5.71 cm

36"91.44cm

Minimum

CabinetWidth

SELECT APPROPRIATE

DUCT CUTOUT

(SEE DUCTING

INSTRUCTIONS.)

CUTOUT

DIMENSIONS

ARE

CRITICAL

12%"

32.38 cm

Min.ClearanceRequired

17½"44.46cm

_'_31 76 cm

1/2" NPT EXT

THREADED NIPPLE

1%"

4.44 cm

CUTOUT

mln.

Minimum cabinet to motor

clearance for cooling purpose.

INSTRUCTIONS TO INSTALLER:

• Side Clearance - Unit may be safely installed as near as 2" (5.08 cm) from a side wall if space

limitations require. However, a side clearance of at least 6" is recommended for optimum

ventilation.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

8101 P575-60

(04-04-00)

Summary of content (7 pages)

PAGE 1
EXPRESSIONS GAS COOKTOP mmmJENN.AIR 408 WEST FOURTHSTREET, NORTH • NEWTON,IA 50208 IMPORTANT: Installation should be performed only by a Jenn-Air Authorized Servicer or other qualified installer. Read safety precautions in the Use & Care Manual before using this appliance. (Dimensions shown in both inches and centimeters.) GAS CONNECTION AXIS I I I 36" 91.44cm Minimum CabinetWidth 5.71 cm CUTOUT DIMENSIONS ARE CRITICAL SELECT APPROPRIATE DUCT CUTOUT (SEE DUCTING INSTRUCTIONS.
PAGE 2
Location Of Your Jenn-Air Appliance Locate this appliance away from combustible materials such as window curtains and combustible wall decorations. The minimum horizontal clearance between the edge of the appliance and adjacent combustible construction is: • 0.75 inches (1.90 cm) at rear; • 2 inches (5.08 cm) at sides These minimum clearances pertain to vertical surfaces between the countertop level and a level 18" above the countertop.
PAGE 3
Installation Of Appliance Follow accompanying ducting instructions carefully. This appliance is designed to always be vented outdoors. This appliance should be ducted separately from other vented appliances. This appliance is designed for use with the gas appliance pressure regulator provided. The installation of this appliance must conform with local codes or, in the absence of local codes, with the latest edition of the National Fuel Gas Code, ANSI Z223.1 USA or current CAN/CGA-B149 INSTALLATION CODE.
PAGE 4
Connecting Appliance To Electricity WARNING Manifold Pi Appliance Pressure Regulator, supplied ELECTRICAL --- /_ku 21LL (Observe directionality of Gas Flow) Motor I Flare Union ,_1/2" -_ Flexible Appliance Connector _ (5 ft. max.) Do not cut or remove the grounding prong from this plug.
PAGE 5
Converting Appliance With LP Gas For Use WARNING Propane conversion is to be performed by a JENN-AIR AUTHORIZED SERVICER (or other qualified agency) in accordance with the manufacturer's instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for this conversion.
PAGE 6
Installation of LP Orifice Spuds With a quarter, engage slot and rotate cap 1/8 of a turn counterclockwise. To remove cap, turn cap over and reinstall. Q Q Q @@ Q @ Natural Setting LP Setting Figure 8: Conversion of Harper- Wyman Appliance Pressure Regulator Figure B, 6 Invert Cap in Appliance Pressure Regulator (See figures 7 and 8.) With the appliance installed, the regulator is located on the underside of the burner box on the right hand side at the inlet to the gas manifold.
PAGE 7
To Convert Appliance Natural Gas For Use With of Natural Gas Orifice Spuds If this appliance has been converted for use with LP gas, each of the following modifications must be performed to convert the unit back to natural gas. A. Installation Replace all orifice spuds Perform Steps 1 through 4 on page 4. For Step 5: Locate the colored brass natural gas orifice spuds that were originally installed in this appliance before its conversion for use with LP gas.