Installation guide
Installing
Brackets
Before
Placing
Cooktop
in
Cutout
Installing
Brackets
After
Placing
Cooktop
in
Cutout
1.
Using
2
or
more
people,
place
the
cooktop
upside
down
ona
1.
Using
2
or
more
people,
place
cooktop
right
side
up
into
the
covered
surface
using
the
foam
end
posts
from
the
cutout.
packaging.
Make
sure
that
the
knobs
are
not
resting
on
the
NOTE:
Make
sure
that
the
front
edge
of
the
cooktop
is
foam.
parallel
to
the
front
edge
of
the
countertop.
If
repositioning
is
2.
Remove
the
attachment
screws
for
the
bracket
locations
from
needed,
lift
entire
cooktop
up
from
cutout
to
avoid
scratching
the
bottom
of
the
cooktop
base.
the
countertop.
3.
Select
bracket
mounting
holes
that
will
allow
the
bracket
to
2.
Remove
the
attachment
screws
for
the
selected
bracket
extend
far
enough
out
from
the
cooktop
for
the
installation
of
locations
from
the
bottom
of
the
cooktop
base.
2%"
(6.4
cm)
clamping
screws. See
the
“Attach
Cooktop
to
Countertop”
section
for
illustration
of
clamping
screw
installation.
3.
Select
bracket
mounting
holes
that
will
allow
the
bracket
to
extend
far
enough
out
from
the
cooktop
for
the
installation
of
2'2"
(6.4
cm)
clamping
screws.
A.
Cooktop
B.
Cooktop
base
C.
Attachment
screw
D.
Clamping
bracket
(extends
far
enough beyond
cooktop
base
to
allow
installation
of
clamping
screws)
E.
2 42"
(6.4
cm)
clamping
screw
(to
be
installed
in
A.
Edge
of
cooktop
base
bottom
B.
Clamping
bracket
C.
Bracket
mounting
holes
D.
Bracket
clamping
hole
E.
Attachment
screw
“Attach
Cooktop
to
Countertop”)
F.
Countertop
4.
Attach
brackets
to
cooktop
base
bottom
with
bracket
attachment
screws
using
the
bracket
mounting
holes
4.
Attach
brackets
to
cooktop
base
bottom
with
bracket
selected
in
Step
3.
attachment
screws
using
the
bracket
mounting
holes
5.
Rotate
brackets
so
they
do
not
extend
beyond
edge
of
selected
in
Step
3.
Securely
tighten
screws.
cooktop
base.
6.
Tighten
attachment
screws
enough
to
hold
brackets
in
place
when
cooktop
is
placed
in
cutout.
7.
Using
2
or
more
people,
turn
the
cooktop
right
side
up
and
place
in
cutout.
NOTE:
Make
sure
that
the
front
edge
of
the
cooktop
is
parallel
to
the
front
edge
of
the
countertop.
If
repositioning
is
needed,
lift
entire
cooktop
up
from
cutout
to
avoid
scratching
the
countertop.
8.
Loosen
the
screws
and
rotate
the
brackets
so
that
they
are
perpendicular
to
the
edge
of
the
cooktop
base
and
extend
beyond
its
edge.
Securely
tighten
screws.