Installation guide
3-Wire
Cable
from
Power
Supply
to
3-Wire
Cable
from
Attach
Cookior
p
fo
Ce
uNnieriop
B.
Red
wires
Cooktop
NOTE:
This
section
applies
only
if
you
are
using
clamping
IMPORTANT:
Use
the
3-wire
cable
from
power
supply
where
brackets.
local
codes
permit
connecting
the
frame-ground
conductor
to
the
neutral
(white)
junction
box
wire:
A-
|
B
E.
Junction
box
F.
White
wire
(from
power
supply)
G.
UL
listed
wire
connector
H.
Black
wires
A.
3-wire
cable
from
power
supply
C.
Green
or
bare
ground
wire
(from
cooktop)
D.
3-wire
cable
from
cooktop
A.
Glass
cooktop
B.
Cooktop
base
C.
Attachment
screw
D.
Clamping
bracket
(extends
far
enough
beyond
cooktop
base
to
allow
installation
of
clamping
screws)
E.
2
38"
(6.4
cm)
clamping
screw
F.
Countertop
G.
Foam
seal
I.
UT
Usted
or
CSA
approved
1.
Place
the
2%"
(6.4
cm)
clamping
screws
into
the
outermost
hole
in
the
clamping
bracket.
Disconnect
power
2.
Use
a
screwdriver
to
tighten
the
screws
against
the
Remove
junction
box
cover,
if
present.
countertop.
Do
not
overtighten.
Connect
the
flexible
cable
conduit
from
the
cooktop
to
the
junction
box
using
a
UL
listed
or
CSA
approved
conduit
:
connector.
1.
Check
that
all
ote
are
now
installed.
If
there
is
an
extra
part,
Tighten
screws
on
conduit
connector
if
present.
go
back
through
the
steps
to
see
which
step
was
skipped.
Connect
the
two
black
wires
together
using
the
UL
listed
wire
2.
Check
that
you
have
all
your
tools.
connectors.
3.
Dispose
of/recycle
all
packaging
materials.
Connect
the
two
red
wires
together
using
the
UL
listed
wire
4.
Use
amild
solution
of
liquid
household
cleaner
and
warm
connectors.
water
to
clean
cooktop
before
use.
Dry
thoroughly
with
a
soft
Connect
the
green
or
bare
cooktop
cable
wires
to
the
white
cloth.
For
more
information,
see
the
“Cooktop
Care”
section
(neutral)
wire
in
the
junction
box
using
the
UL
listed
wire
of
the
Use
and
Care
Guide.
connectors.
5.
Read
the
“Cooktop
Use”
section
in
the
cooktop
Use
and
Install
junction
box
cover.
Care Guide.
Reconnect
power.
6.
Reconnect
power.
NOTE:
If
the
cooktop
does
not
work
after
turning
on
the
power,
check
that
a
circuit
breaker
has
not
tripped
or
a
household
fuse
has
not
blown.
See
“Troubleshooting”
section
in
the
Use
and
Care
Guide
for
further
information.
If
You
Need
Assistance
or
Service:
Please
reference
the
“Assistance
or
Service”
section
of
the
Use
and
Care
Guide
or
contact
the
dealer
from
whom
you
purchased
your
cooktop.