Installation guide

Cabinet Dimensions Cutout Dimensions
A. 30" (76.2 cm) on 30" (76.2 cm) models
36" (91.4 cm) on 36" (91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet (24" [67 cm]
minimum clearance if bottom of wood or metal cabinet is covered
by not less than 34" [0.6 cm] flame retardant millboard covered with
not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless
steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E.2" 6.1 cm)
F. 21 38" (73.4 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
|. Junction box or outlet; 10" (25.4 cm) from right-hand side of
cabinet
J. 28 78" (73.4 cm) on 30" (76.2 cm) models
34¥2" (87.6 cm) on 36" (91.4 cm) models
K, 2%" (6.4 cm) minimum distance to nearest left and right side
combustible surface above cooktop
L. 1%" (3.8 cm) minimum clearance between back wail and
countertop
NOTES: After making the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the cooktop base. To avoid this modification, use a base cabinet
with sidewalls wider than the cutout.
A minimum side clearance of 6" (15.2 cm) is recommended
between side of cooktop and side wall for maximum
ventilation performance.
A minimum clearance of 2” (5.1 cm) is recommended
between the motor/blower and cabinet for proper cooling. A
6" (15.2 cm) clearance is recommended for servicing access.
C. 898" (21.9 cm) on 30" (76.2 cm) models
A. 28 7" (73.4 cm) maximum on 30" (76.2 cm) models
34%2" (87.6 cm) maximum on 36" (91.4 cm) models
B. 21%" (53.7 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)
models
15 6" (39.2 cm) on 36" (91.4 cm) models
D. 6 %e" (16.0 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models
E.2" (5.1 cm) minimum space to front edge of cooktop
F. Floor exhaust option
G. 6 48" (15.6 cm) for 6" (15.2 cm) vent system
H. 898" (21.9 cm) on 30" (76.2 cm) models
15 He" (39.2 cm) on 36" (91.4 cm) models
1, 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models
J. Wall exhaust option
4 geo, wm,
Venting Requirements
IMPORTANT: This cooktop must be exhausted outdoors unless
using the Jenn-Air® Duct Free Filter Accessory Kit. See “Venting
Methods” section.
Do not terminate the vent system in an attic or other enclosed
area.
Use a Jenn-Air® vent cap.
Vent system must terminate to the outside.
Use only a 6" (15.2 cm) round metal vent. Rigid metal vent is
recommended. For best performance, do not use plastic or
metal foil vent.
Before making cutouts, make sure there is proper clearance
within the wall or floor for the exhaust vent.
Do not cut a joist or stud unless absolutely necessary. If a
joist or stud must be cut, then a supporting frame must be
constructed.
The size of the vent should be uniform.
The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.
Use vent clamps to seal all joints in the vent system.
Use caulking to seal exterior wall or roof opening around the
cap.
Determine which venting method is best for your application.