Installation guide

ManualsBrandsJenn-Air ManualsCooktopJGD8130ADS

CONVERTIBLEGAS GRILL

COOKTOPSERIES

JGD8130 & JGD8345

JENN-AIR

DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS

*Blowermay be rotated for horizontal or verticaldirection by looseningnuts aroundblowerinlet. Accessible insideventilation

chamber.

• NOTICE TO INSTALLER: Leave these instructions with the appliance.

• NOTICE TO CONSUMER: Retain these instructions for future reference.

REGULATOR

TIEDOWNBOLT

ON EACHEND BOXCOVER

GREASE

BLOWERCANBE CONTAINER

SWIVELED90°

29"_1/

21"+1116"

7Q/16"

Min.

Cbarar_e

2.38cm

SELECTAPPROPRIATE

DUCTCUTOUT(SEE

DUCTINGINSTALLA-

TIONINSTRUCTIONS). _EAS[

CONTA t NER

2 7/8 °_ _13 3/4"--,.*_.|t 13/115-_..

7.3 Cm 34.9 cm 30.0 cm

TtEDOWNBOLT

ONEACHEND

GREASE

BLOWERCANBE CONTAINER

SWIVELED90'=

APPUANCEPRF.SSURE

REGULATOR

SELECTAPPROPRIATE

DUCTCUTOUT

DUCTINGINSTALLA-

TIONINSTRUCTIONS).

43 114"+lt 21" _-1/16"

79/16"

19.21cm

17_"

Min.

4.76cm

COH_AI_

INSTRUCTIONSTO INSTALLER

• Dimension"A"- Provide 2" rain. (5.08 cm) cabinet clearance to motor for coolingpurpose,

• Note - Where possible,6" (15.24 cm) isrecommendedfor motor/blowerservice.

• Side Clearance - Grills installednear a side wall mustallow a minimum clearance of8".

• Access must be providedto remove and empty grease container(s),

8101P406-60

(o9-ol-oO)

Summary of content (8 pages)

PAGE 1
CONVERTIBLE GAS GRILL COOKTOP SERIES JGD8130 & JGD8345 JENN-AIR DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS *Blower may be rotated for horizontal or verticaldirection by looseningnuts aroundblower inlet. Accessible insideventilation chamber. • NOTICE TO INSTALLER: Leave these instructions with the appliance. • NOTICE TO CONSUMER: Retain these instructions for future reference.
PAGE 2
Installing Cabinetry Over Your Jenn-Air Grill *A = 30" (76.2 cm) minimum verticat clearance between cooking surface and construction above the appliance. *B = 13" (33.02 cm) maximum depth of cabinets installed above cooking top. of local codes, with the latest edition of the National Electrical Code ANSI/NFPA No. 70 USA or current CSA STANDARD C22.1 Canadian Electrical Code part 1. Warranty Isvoid on JEN_AIR Do_edl_nes tnd_a_ _nge hood construction equ_rne_ _ tt-_ asr_x_nmen_.bymar_fa_.
PAGE 3
InstructionsTo Installer Nr Shutter Adjustment 1. Chamfer all exposed edges of decorative laminate to prevent damage from chipping. This appliance is shipped from the factory with air shutters adjusted for use with N=ural Gas. If further adjustment is necessary, or to reset for use with LP, adjust air shutters as follows: 2, Radius corners of cutout and file to insure smooth edges and prevent corner cracking. Recommend 1/4" or 3/8" diameter drill in each corner, 3.
PAGE 4
Low Flame Adjustment (SeeIllustration "C") PressureTesting This appliance is shipped from the factory with low and mediumflame settingsadjusted for use with Natural Gas. If further adjustment is necessary, or to readjust for use with LP, proceed as follows: The maximum gas supply pressure for the appliance pressure regulator supplied on this appliance is 14" W.C. The test pressure for checking this appliance pressure regulator must be at least 6" W.C. for Natural Gas, and at least 11" W.C for LP.
PAGE 5
ConversionTo LP Gas This appliance is shippedfrom the factory equipped for use with Natural Gas. To convert it from Natural Gas for use with LP Gas, perform steps 1 through 4. I_OPEN END WRENCH 1. Remove natural gas orifice hoods. Install color coded orifice hoods supplied, located in a pack attached to the outer plenum area of this appliance. (See illustration "E" below, and LP Gas Conversion Instructions on page 6). TURN COUNTERCLOCKWISE TO REMOVE 2.
PAGE 6
TO CONVERTAPPLIANCEFOR USE WITH PROPANEGAS Natural Gas To Propane Gas (LP) Conversion Instructions ...,, . F.LECTmCAL __ Authorized Service Contractor (or other qualifiedagency) in accordancewith the _man_s:!nstructlons e, S.UST TURNEDOFF PRIOR.TOC0¢__:' r_, anda, codesand ='_uL_'n_, ,of _the , authority having u_o_ Failure to follow instructions could .,_ult_ serious "injury or property damage. The _ualif!_ agency performing this work assumes responsibility for this conversion.
PAGE 7
TO CONVERTAPPLIANCEFOR USE WITH NATURALGAS Propane Gas (LP) To Natural Gas Conversion Instructions Models - JGD8130 & JGD8345 Series If this appliance has been converted for use with LP Gas, each of the following modifications must be performed to convert the unit back to Natural Gas Incoming Natural Gas pressure required to appliance pressure regulator - 6" - 7" W.C. Manifold - Natural Gas pressure required - 5" W.C. Natural Gas input specified, Model JGD8130/JGD8345 36,000 BTU/hr / 56,000 BTU/hr. A.
PAGE 8
REQUIREDADJUSTMENTSAT TIME OF INSTALLATION The installation of this appliance must conform with local codes, or in the absence of local codes, with the latest edition of the National Fuel Gas CodeANSI Z223.1 USA or current CAN/CGA-B149 Installation Code. -'-']Thisto LPrange was manufactured use with instructions. Natural Gas. If LP gas is the fuel of choice, follow the conversion procedure found in the for installation ----] Test all external connections ----] Test all electrical for gas leaks.