_ About Your . _[enn-Alr Refrigerator Your Jenn-Air frost-free refrigerator was designed, engineered, and manufactured to the highest standards of quality and performance. Since this manual explains how you can obtain the best use of your Jenn-Air, it is essential that you follow the instructions carefully. Should you have any questions about using your Jenn-Air appliance, write to us. Be sure to provide the model number of your appliance.
Convenience Center Freeze r Door Shelves Automatic Ice Maker " and Automatic Dispenser Bin Freezer Control Refrigerator Control Wine Rack Egg Caddy I Dairy Compartment Shelf Tender / / Freezer Shelves Lift-Off Bulk Storage Drawer Drawer .
Installat o Location If you are installing your new refrigerator yourself, please follow these helpful suggestions. 1. Remove base skids and reinsert two front levelers. Discard two rear levelers. 2. Remove all exterior and interior tape carefully and retain old tape. Make a small pad of this tape to pick off any remaining tape residues. This will eliminate the need to use dangerous solvents of any kind. 3.
TOCORRECT THIS TOCORRECT THIS CONDITION, RAISE RIGHT CORNER AND /OR LOWERLEFT CORNER UNTIL DOORSALIGN ACROSS TOPOF CABINET. CONDITION, RAISE LEFTCORNER AND /OR LOWERRIGHT CORNER UNTIL DOORSALIGN ACROSS TOPOF CABINET. Electrical Connection and Grounding This appliance is designed to operate on a nominal 115volt, 15 amp, 60 cycle line. There should be a separate, grounded circuit, serving this appliance only. DO NOT use an extension cord. POWER SUPPLY CORD WITH.
Oporat,o° Setting Controls Your new refrigerator has two controls. One for regulating the temperature in the refrigerator compartment and one for the freezer compartment. Both controls are located at the upper rear of the refrigerator compartment, just below the light shield. ..................... ,,.-...... 0_..............,........... _ -- To start your refrigerator, set the refrigerator control on "F" and set the freezer control on "4". G I_ i EI 5 4 3 21' TURN.................
Refrigerator Compartment Features To maintain the natural flavor, moisture, and nutrition of fresh foods, we recommend that all dishes, trays, and containers of food be covered. Shelves tioned to suit your special needs. To remove a shelf, lift the rear straight up a fraction of an inch and pull straight out. To lock into another position, tilt the shelf with the front up. Insert hooks into desired frame openings and let the shelf settle into place.
Door (Models JRS226 JRSD226 Only) Features and \ Door shelf fronts can be removed for easy cleaning of the door liner and shelf fronts. Lift the shelf Easy-Off Shelf front straight up until it clearsFronts the retainerson the door liner and pull straight out. Reverse this procedure when replacing the door shelf front. (Models JRS226 JRSD226 Only) (Model E_ and Lift-offshelvesmay be easilyadjusted to another position on the door.
Freezer Compartment Features To maintain the natural flavor, moisture, and nutrition of frozen foods, and to prevent freezer burn, we recommend that all foods be wrapped or sealed properly. Shelves To remove a freezer shelf, lift the shelf straight up, tilt sideways and pull straight out. When replacing a freezer shelf, reverse the removal procedure.
Ice cubes that have been in the ice storage bin for a considerable length of time may pick up off-flavor taste, stick together, and gradually become smaller. We suggest that these cubes be thrown away. We also suggest using an open box of baking soda in the refrigerator for food odor absorption. Certain sounds may tor may have a slight will rattle as they fall sionally. All of these accompany the various operating cycles of the ice maker.
Removing Ice Cube and Replacing Dispenser Bin the Automatic (]RSD226 Only) Lift the front of the Automatic Dispenser bin and pull it straight out. Wash the bin occasionally in mild soap and lukewarm water. To replace the bin, push it all the way back until the bottom of the bin is behind the raised edge at the front of the shelf it rests upon. Make sure the tabs, at the back of the bin, that turn the spiral auger are positioned between the prongs from the auger motor.
Cleaning It is recommended that you disconnect the power cord before cleaning. Your refrigerator can be rolled out for cleaning. Turn the levelers, at each front corner of the cabinet, counterclockwise until they turn freely.Then pull the cabinet straight out. Note: If you have an automatic ice maker installed, we recommend that you turn off the water supply before moving the cabinet.
Lift front of defrost pan and pull straight out. _IDE R_LS To replace, reverse procedure as shown. __"_-__-_.-_ in the and tap end in until grille on thecabinet base grille witheach the square openings locks in place. To replace base grille, line up the spring clips Condenser The condenser should be cleaned at least twice a year. If you move your refrigerator out for cleaning, the condenser can be cleaned through the rear access opening.
Other HintsRefrigerator on Caring For Your Replacing It is recommended bulbs. Light Bulbs that youdisconneet the power cord before replacing light To replace upper refrigerator light bulb! _.1) grasp the light shield near the ends and pull out until the shield pulls free of the retainer lugs,'2) unscrew bulb and replace with a 60 watt appliance bulb; and 3) hook the light shield over the upper retainer lugs and press in at the bottom until the shield snaps in place.