Installation guide

ManualsBrandsJenn-Air ManualsVentilation HoodJXT8042ADS

RANGE HOOD

Modal Number: [XTS030ADS [×T8036ADS

Manufacturer Number: S99E30S $99E36S

Size: 30" 36"

[XTB042ADS

S99E42S

42"

GUIDE

TABLE OF CONTENTS

Safet, Instructions .................................................... 1

List of Materials ....................................................... 2

Mounting Heights .................................................... 3

Ducting .................................................................... 4

Specifications ........................................................... 5

Installation ............................................................ 6-7

Form No. A/04/03 Part No. IS9900-0303A (02004 Maytag Appliances Sales Co, Litho U,S.A,

Summary of content (8 pages)

PAGE 1
RANGE HOOD Modal Number: Manufacturer Number: [XTS030ADS S99E30S [×T8036ADS $99E36S [XTB042ADS S99E42S Size: 30" 36" 42" GUIDE TABLE OF CONTENTS Safet, Instructions .................................................... 1 List of Materials ....................................................... 2 Mounting Heights .................................................... Ducting .................................................................... Specifications .....................................
PAGE 2
MODELS: JXT8030AD$ JXT8036AD$ JXT8042AD$ Installation Theinstallation in this manuaris intended for qualifiedinstarlers,servicetechniciansor persons with similarquarifiedbackground,DONOTattemptto instarlthis apprianceyourserf,hiury courd resultfrom installingthe unitdue to rackof appropriateerectricarand technicarbackground, Air erectricar wiring must be prope@ installed, insulated and grounded.
PAGE 3
LiST OF MATERIALS 1 - Hood Body 1 - Duct CoverAssemNy (2 pieces) 1 - Parts Bag: 1 - Duct Cover Mounting Bracket 2 - Mounting Brackets Packet of Mounting Screws 2 - Metallic Filters 1 - Metallic Bitterfly Damper NO DUCTINGiS iNCLUDED
PAGE 4
MOUNTINGHEIGHTS& CLEARANCE Minimum mounting height betweenrangetop to hood bottom shouldbe no less than 24". 28,94"-46,65" Maximum mounting heightshould be no higher than 32". It is importantto install the hoodat the proper mountingheight. Hoodsmounted too low could result in heat damageand fire hazard; while hoodsmountedtoo high will be hard to reach and will lose performanceand efficiency.
PAGE 5
DUCTING NEVERexhaust air or terminate duct work into spaces between walls, crawr spaces, ceiling, attics or garages. Air exhaust must be ducted to the outside. UseMetal ductwork only. FastenaHconnections with sheet metal screws and tape aHjoints w/certified SHyerTape or DuctTape.
PAGE 6
SPECiFiCATiONS ELECTRICAL AHEHectricaH work must by performedby qualifiedeHectficianor personwith similar technicaH know howand background. Forpersonalsafety,removehousefuse or opencircuitbreakerbeforebeginninginstallation. Donot useextensioncordor adapterprugwith this appriance. Follow NationaleHectricaH codesor prevaH#lgHocaH codesand ordinances.
PAGE 7
MOUNTINGTHEfiANGEHOOD 1. Screw mounting brackets onto left and right side of blower unit. 2. Attach blower to canopy, fasten with screws from below. 3. Determine hood height, center, mark, level and hang hood to wall through mounting keyholes on back. 4. Install duct work and electrical. 5. Locate and fasten bracket for upper telescopic duct cover onto the wall. 6. Slip upper and lower telescopic duct covers onto top of blower and screw in place. 7.
PAGE 8
DUCTLESSCONVERSION Ductbss conversion is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a "purifying" hood rather than an exhaust hood. Fumes and exhaust from cooking is drawn and filtered by a set of optional CarbonFilters. The air is then purified and re°circulated hack within the home. We recommend to ALWAYSexhaust air outside of the home by employing existing or installing new duct work, if possibb.