Use and Care Manual

23
Max Cool
The Max Cool feature assists with periods of high refrigerator use,
full grocery loads, or temporarily warm room temperatures.
■ To turn on the Max Cool feature, press the Max Cool button.
When the button is pressed, the icon will blink 3 times, and
appear on the display screen.
■ To manually turn off the Max Cool feature, press the Max Cool
button and the display will blink 3 times and turn off. The Max
Cool feature will remain on for 24 hours unless manually turned
off. Adjusting the refrigerator temperature
will automatically turn off the Max Cool feature.
NOTE: Setting the freezer to a colder temperature may make
some foods, such as ice cream, harder.
Max Ice
The Max Ice feature assists with increasing the cooling for the
freezer compartment in order to increase ice production.
■ To turn on or off the Max Ice feature, press the Max Ice button.
When the button is pressed to turn the feature on, the icon will
blink 3 times, and appear on the display screen.
■ To manually turn off the Max Ice feature, press the Max Ice
button and the display will blink 3 times and turn off. The Max
Ice feature will remain on for 24 hours unless manually turned
off. Adjusting the refrigerator temperature will automatically
turn off the Max Ice feature.
NOTE: Setting the freezer to a colder temperature may make
some foods, such as ice cream, harder.
Water Filter Reset
Displays the status of the water filter. To reset the filter, press MAX
ICE and MAX COOL for 3 seconds. After countdown, the Good
icon will blink 3 times and remain lit.
NOTE: The Water Filter status lights on the internal controls will
let you know when to change your water lter.
■ ORDER FILTER (Yellow) - Order a replacement water lter.
■ REPLACE FILTER (Red) - Replace the water lter. While you
are dispensing water, “Replace” Filter icon will ash constantly
from beginning to the end of dispensing. After 14 days without
replacing the water lter, the “Replace” Filter icon will blink
7 times and an alert tone will sound 3 times at the end of
dispensing. See the “Water Filtration System” section.
NOTE: REPLACE FILTER will remain illuminated if a lter reset
is not done.
■ RESET FILTER - Touch MAX ICE and MAX COOL at the same
time on the Temperature Control display for 3 seconds to reset
water lter. The display will do a 3-second countdown and
then ash the icon and play a tone.
Filter Status
The JennAir app will send an alert that displays the water lter
status.
Energy Saver Mode
A selectable feature that turns off the heaters around the
refrigerator doors and dispenser. When this feature is enabled,
condensation may form on the front of the refrigerator cabinet,
gasket, or on top of the freezer drawer. Savings may vary based
on the relative humidity of environment.
■ To turn the mullion heater off, press and hold the Energy Saver
button for 3 seconds. The Energy Saver icon will blink 3 times
and then remain lit as shown.
IMPORTANT: When Energy Saver is enabled and the LED is ON,
the dispenser heater and vertical mullion heater will be turned off.
■ Press and hold ENERGY SAVER for 3 seconds again to turn
the heaters back on.
Pure Freeze
®
Mode
This feature minimizes moisture migration from frozen food.
This in turn reduces the freezer burn occurrence.
To turn on the Pure Freeze
®
mode, toggle to the coldest freezer
temperature set point.
To turn off the Pure Freeze
®
mode, toggle from the coldest freezer
set point to any other temperature.
Sound On/Off
The Sound button allows the customer to turn the sound on
and off.
■ To turn on the Sound feature, press the Sound button. When
the button is pressed, the sound icon will blink 3 times and
appear on the display screen.
■ To manually turn off the Sound feature, press the Sound button
and the display will blink 3 times and turn off.
Power Outage
The Power Outage indicator lets you know if the power supply to
the refrigerator has been off and the freezer temperature has risen.
The control panel display will read “Power Outage” and an alert
tone will sound 3 times. Touch any button to stop the tone and
touch any button again to turn off Power Outage icon.
Once the power outage has been conrmed, “Power Outage” icon
will disappear and the display will return to the Home screen.
Showroom Mode
This mode is used when the refrigerator is on display in a retail
store or if you want to turn the cooling off and deactivate all other
functions except interior lighting. Showroom mode can be used
when going on vacation. See the “Vacation and Moving Care”
section for proper steps on leaving your refrigerator in this mode
for long periods of time.
If you turn on Showroom mode, the word “Showroom” will light
up on the display. Enter or Exit Showroom mode by pressing and
holding °F/°C and DRAWER at the same time for 3 seconds.
NOTE: Empty ice maker if refrigerator is going to be turned off for
an extended period of time.
Sabbath Mode
Allows the door of the refrigerator or freezer to be opened or
closed during the Sabbath or other religious holidays without
activating the interior lights or controls.
The freezer and refrigerator user set points remain unchanged
while in this mode. If you unintentionally turn on Sabbath mode,
the word “Sabbath” will light up on the display. Enter and exit
Sabbath mode by pressing and holding °F/°C and SOUND at the
same time for 3 seconds.
NOTE: You will be unable to dispense or change temperature set
points in Sabbath mode. Your interior lighting and control panels
will all be inactive in Sabbath mode.