GETTING STARTED BUILT-IN REFRIGERATOR ARMOIRE-STYLE DOOR PANEL KIT INSTALLATION INSTRUCTIONS ENSEMBLE DE PANNEAUX DE PORTE DE STYLE ARMOIRE POUR RÉFRIGÉRATEUR ENCASTRÉ INSTRUCTIONS D’INSTALLATION W11286875A GETTING STARTED | 1
BUILT-IN REFRIGERATOR ARMOIRE-STYLE DOOR PANEL KIT 2 | GETTING STARTED
INTRODUCTION SAFETY TABLE OF CONTENTS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or WARNING.
INTRODUCTION REGISTRATION REGISTERING YOUR PRODUCT PRODUCT IDENTIFICATION Gain access to our concierge-level Customer Support by registering your appliance. We make product registration simple and straightforward so that you can start using your exclusive JennAir benefits today. Your product identification, which includes the model and serial numbers, is listed on the product rating plate.
SITE PREPARATION BEFORE INSTALLATION IMPORTANT: These instructions are intended as a general guide only and do not supersede any national or local codes in any way. Compliance with all local, state, or national codes pertaining to this type of installation should be determined prior to installation. These instructions are intended to supplement the Installation Instructions provided with your refrigerator, not replace them.
SITE PREPARATION BEFORE INSTALLATION (CONTD.) PARTS SUPPLIED WITH REFRIGERATOR Parts Supplied with Refrigerator (Needed for Armoire Installation): Phillips-head flat screw Black: 8281252 All hardware Hinge cover trim (RC and FC) Side trim Handle side door trim Installation block Panel templates The following parts are either not needed to install the panels in this kit, or they are already installed on the panels.
SITE PREPARATION INSTALLATION REQUIREMENTS OPENING REQUIREMENTS CABINET AND PANEL INSTALLATION OPTIONS IMPORTANT: IMPORTANT: Cabinet Depth - 25" (63.5 cm) ■■ Install the handles on the panels prior to panel installation. Follow the instructions received with handle kit to install the handles. ■■ Plan your installation using these instructions in conjunction with the Installation Instructions provided with the refrigerator.
SITE PREPARATION CABINET CUTOUT OPTIONS AIRFLOW VENTING RECOMMENDATIONS IMPORTANT: Armoire-style installations recommends a minimum of 1/8" (3.2 mm) of open space above the refrigerator. It is recommended that this space not be blocked in any way, including soffits. Models may be installed using either Option 1, Option 2 or option 3. Option 1 - Open to Ceiling Option 2 - False Front (cabinet face only) Option 3 - Closed Soffit False front Open to ceiling 8 | SITE PREPARATION 1/8" (3.
SITE PREPARATION PANEL DIMENSIONS BOTTOM MOUNT MODEL Maximum allowable weights: • Door panel - 60 lbs (27.2 kg) • Drawer panel - 25 lbs (11.3 kg) ! Maximum allowable weights: • Door panel - 38 lbs (17.2 kg) • Drawer panel (36" model) - 25 lbs (11.3 kg) • Drawer panel (42" model) - 30 lbs (13.6 kg) A A B SIDE BY SIDE MODELS ! Maximum allowable weights (42" models): • Refrigerator Door panel - 65 lbs (29.5 kg) • Freezer Door panel - 49 lbs (22.
SITE PREPARATION SECONDARY ANTI-TIP BOARD INSTALLING THE SECONDARY ANTITIP BOARD WARNING The main anti-tip boards for open to ceiling installation are secured at 84" (213.36 cm) from the floor (rear side). Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Install secondary anti-tip board to ensure product stability. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury.
INSTALLATION INSTALLING GRILLE BRACKET ASSEMBLY APPLIES TO: WARNING Excessive Weight Hazard 1 Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. 1. Remove the three screws fastening each mounting plate to the top of the refrigerator on each side. Discard the mounting plates but keep the screws for attaching the two grille bracket assemblies provided in this kit. 2. Remove the two screws fastening the air divider to the unit housing.
! INSTALLATION Align the base of foam air divider with base of unit housing INSTALLING AIR DIVIDER APPLIES TO: 1 1. Peel away the paper layer from the foam air divider to reveal the adhesive side. 2. Stick the foam air divider to unit housing at the location where metallic air divider was installed earlier by applying even pressure.
INSTALLATION INSTALLING GRILLE PANEL APPLIES TO: 2 1. Position the grille panel between the grille brackets on each side of the cabinet. 2. Hook the top of grille onto the upper rivet pins. Rotate downward and push the bottom of the grille panel in until the grille panel snaps into place. 1 Parts to be used: X1 Grille panel 2 INSTALLATION | 13 INSTALLATION NOTE: For grille panel removal, push the top of grille panel inward until the lower portion snaps out. Rotate and lift off the grille panel.
INSTALLATION MARKING DOOR PANEL TOP BRACKET LOCATION(S) APPLIES TO: 63⁄4" (17.2 cm) A B C A. Top of custom refrigerator door panel B. Drilling template C. Bottom of custom refrigerator door panel 14 | INSTALLATION IMPORTANT: For an Armoire installation, instead of drilling holes along the top edge(s) of the custom door panel(s), you must adjust the placement of the drilling template (provided with the refrigerator). NOTES: ■■ No template adjustment is needed for the bottom edge of the door panel(s).
INSTALLATION INSTALLING PANEL TOP BRACKET(S) AND SHOULDER WASHERS APPLIES TO: Hinge side Fasten the refrigerator/freezer door panel top bracket to custom wood door panel using hex-head pointed screws (2) at marked screw locations (refer "Marking Door Panel Top Bracket Location(s)" section). 2. For marking location of the shoulder washers, Measure ‘A’ from the top of the panel, measure ‘B’ from side of panel. Mark the hole locations as shown in Figure.
! INSTALLATION FOR SIDE BY SIDE MODELS - SKIP THIS STEP INSTALLING FREEZER BRACKETS APPLIES TO: A 2" (52.77 mm) 55/8" (143.3 mm) 47/8" (123.4 mm) 55/8" (143.3 mm) 16 | INSTALLATION 1. For marking location of the freezer bracket screws, Measure ‘A’ from the top of the panel. Mark the hole locations as shown in Figure. Refer to Table 2 for ‘A’ dimension based on the models. 2. Fasten the freezer bracket to custom wood drawer panel at marked screw locations in step 1. 3.
! INSTALLATION FOR SIDE BY SIDE MODELS - SKIP THIS STEP INSTALLING FREEZER PANEL APPLIES TO: 1 Slightly loosen the bracket screws present on freezer panel. NOTE: Be sure that the refrigerator door(s) are tightly closed. 2. Slide panel onto drawer. Retighten the four screws on each side attaching the bracket to the drawer panel. 3. Using the Phillips-head flat screws, fasten the panel brackets to the drawer. 4.
INSTALLATION INSTALLING DOOR PANEL(S) APPLIES TO: WARNING 1 Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Install secondary anti-tip board to ensure product stability. Use two or more people to move and install refrigerator. 2 Failure to do so can result in death or serious injury. NOTE: Be sure that secondary anti-tip board is installed before opening the door. Refer “INSTALLING THE SECONDARY ANTI-TIP BOARD” section to install the secondary anti-tip board.
INSTALLATION INSTALLING DOOR PANEL(S) (CONTD.) WARNING Excessive Weight Hazard Use two or more people to move and install panels. Failure to do so can result in back or other injury. Align the two shoulder washers, on the back of the door panel, with the “J” slots on the side of the refrigerator door. 5. Simultaneously slide the panel onto the door, and lower the panel bracket down onto the adjustment pins at the top of the door.
INSTALLATION MOVING REFRIGERATOR TO FINAL POSITION APPLIES TO: WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. 1 A 2 A B A. Rear leveling bolt Move the refrigerator straight back and evenly into the cabinet opening so that all the panels are flush with adjacent cabinets from all sides. 2. Use a 5/16" Nut driver to turn the leveling bolts clockwise to raise the refrigerator.
INSTALLATION ADJUSTING DOOR SWING APPLIES TO: 1. If the standard 110° door swing is too wide, install the door stop pin to allow for a maximum 90° door swing. Insert the door stop pin into the top hinge in the hole shown. Use a 5/32" hex key, to tighten door stop pin.
! INSTALLATION FOR SIDE BY SIDE MODELS - SKIP THIS STEP ADJUSTING FREEZER PANEL APPLIES TO: 1. io la at t Ins l nB k oc 1/8" 22 | INSTALLATION 1 A 1/8" (3.2 mm) gap is required between the panel and adjacent cabinets. Use the installation block to measure the gaps.
INSTALLATION ADJUSTING REFRIGERATOR PANEL(S) APPLIES TO: Slightly loosen the panel bracket screws to allow the panel to move to the left or right. 2. Adjust panels to achieve a 1/8" (3.2 mm) gap between panels and adjacent cabinets. For French door bottom mount and bottom mount models, align the outside edge of the refrigerator panel to the outside edge of the freezer panel on both the sides. For side by side models, align the refrigerator and freezer panels with adjacent cabinets.
INSTALLATION ADJUSTING REFRIGERATOR PANEL(S) (CONTD.) APPLIES TO: A A 4 A. Adjustment pin 1/8" Ins 5 tall 24 24 || INSTALLATION INSTALLATION atio nB loc k 4. Use a 5/32" hex key to raise or lower the adjustment pins which allows the panel to move up or down. 5. A 1/8" (3.2 mm) space is required between panel(s) and bottom of the soffit.
INSTALLATION ATTACHING PANEL(S) APPLIES TO: 1. 1 Using the slotted hex-head screws, fasten the top and bottom hinges to the door panels. Fully tighten all door panel screws. NOTE: Do not overtighten the screws, it may strip the panel. 2. 36" Bottom Mount models only - Use the hex head screws to fasten the panel to the additional door bracket. Slotted hex-head screws (As required) A B 2 C C A. Top hinge B. Mounting bracket C. Holes for screws D E D. Door adjustment pins E.
INSTALLATION ATTACHING PANEL(S) (CONTD.) 3. Use the Phillips-head screws to fasten the panel to the door on vertical hinge side. 4. Use slotted hex-head screws to attach the mounting bracket located at the bottom of the doors, to the door panels.
INSTALLATION COMPLETING THE INSTALLATION APPLIES TO: 1. 2. 3. 1 Reinstall hinge cover(s). Snap the door adjustment pin cover(s) into place. Using the Phillips-head screws, attach the handle side trim pieces (shipped with the refrigerator) to the doors.
ENSEMBLE DE PANNEAUX DE PORTE DE STYLE ARMOIRE POUR RÉFRIGÉRATEUR ENCASTRÉ 28 | MISE EN PLACE
INTRODUCTION SÉCURITÉ TABLE DES MATIÈRES INTRODUCTION Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres.
INTRODUCTION ENREGISTREMENT ENREGISTREMENT DE VOTRE PRODUIT IDENTIFICATION DU PRODUIT Accédez à notre service à la clientèle de niveau concierge en enregistrant votre appareil. Nous simplifions l’enregistrement des produits afin que vous puissiez commencer à utiliser vos avantages JennAir exclusifs aujourd’hui. L’identification de votre produit, qui comprend le modèle et les numéros de série, figure sur la plaque signalétique du produit.
PRÉPARATION DU SITE AVANT L’INSTALLATION IMPORTANT : Ces instructions ne constituent qu’un guide général et ne peuvent en aucun cas être substituées aux prescriptions d’un code national ou local applicable. Avant d’entreprendre l’installation, on doit déterminer les critères de conformité de l’installation aux prescriptions de tout code national, provincial ou local. Ces instructions complètent les instructions d’installation fournies avec le réfrigérateur, mais ne les remplacent pas.
PRÉPARATION DU SITE AVANT L’INSTALLATION (SUITE) Pièces fournies avec le réfrigérateur (utilisées pour l’installation d’armoire) : Vis à tête plate cruciforme noire : 8281252 Matériel de montage Garniture de couvre-charnière (compartiment réfrigération et congélation) Garniture latérale Garniture de porte du côté poignée Cale d’installation Gabarits de panneaux PIÈCES FOURNIES AVEC LE RÉFRIGÉRATEUR Les pièces suivantes ne sont pas nécessaires pour monter les panneaux de cet ensemble ou
PRÉPARATION DU SITE EXIGENCES D’INSTALLATION EXIGENCES D’OUVERTURE OPTIONS D’INSTALLATION DE L’ARMOIRE ET DU PANNEAU IMPORTANT : IMPORTANT : Profondeur de l’armoire – 25" (63,5 cm) ■■ Installer les poignées sur les panneaux avant l’installation du panneau. Suivre les instructions reçues avec la trousse de poignée pour installer les poignées. ■■ Planifier l’installation à l’aide de ces instructions, accompagnées des instructions d’installation fournies avec le réfrigérateur.
PRÉPARATION DU SITE DIMENSIONS DE L’OUVERTURE À DÉCOUPER DANS L’ARMOIRE EXIGENCES DE CIRCULATION D’AIR IMPORTANT : Les installations de panneaux de porte de style armoire nécessitent un dégagement minimum de 1/8" (3,2 mm) au-dessus du réfrigérateur. Cet espace ne devrait pas être bloqué, notamment par d’éventuels soffites. Les modèles peuvent être installés en utilisant l’option1, 2 ou 3.
PRÉPARATION DU SITE DIMENSIONS DU PANNEAU ! Poids maximum autorisés : • Panneau de porte – 60 lb (27,2 kg) • Panneau de tiroir – 25 lb (11,3 kg) MODÈLES DE RÉFRIGÉRATEUR AVEC CONGÉLATEUR EN BAS ET PORTE À DOUBLE BATTANT ! Poids maximum autorisés : • Panneau de porte – 38 lb (17,2 kg) • Panneau de tiroir – (modèle de 36") – 25 lb (11,3 kg) • Panneau de tiroir – (modèle de 42") – 30 lb (13,6 kg) A A A MODÈLES CÔTE À CÔTE ! Poids maximum autorisés (modèles de 42") : • Panneau de porte du réfrigérateur
PRÉPARATION DU SITE PANNEAU ANTIBASCULEMENT SECONDAIRE INSTALLATION DU PANNEAU ANTIBASCULEMENT SECONDAIRE AVERTISSEMENT Les panneaux antibasculement principaux pour les installations avec ouverture vers le plafond sont fixés à 84" (213,36 cm) du plancher (côté arrière). Risque de basculement Le réfrigérateur est lourd au sommet et bascule facilement lorsqu'il n'est pas complètement installé.
INSTALLATION INSTALLER LE SUPPORT DE GRILLE INSTALLATION POUR : AVERTISSEMENT Risque du poids excessif 1 Utiliser deux ou plus de personnes pour déplacer et installer le réfrigérateur. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. 2 3 1. Retirer les trois vis fixant chaque plaque de montage au haut du réfrigérateur sur chaque côté. Jeter les plaques de montage, mais conserver les vis pour fixer les deux supports de grille fournis dans cet ensemble. 2.
INSTALLATION Aligner la base du séparateur d’air en mousse avec la base du logement de l’appareil ! INSTALLATION DU SÉPARATEUR D’AIR EN MOUSSE INSTALLATION POUR : 1 1. Enlever le protecteur en papier du séparateur d’air en mousse pour mettre à nu la pellicule collante. 2. Coller le séparateur d’air en mousse au compartiment de l’appareil où le séparateur d’air en métal était installé en appliquant une pression uniforme.
INSTALLATION INSTALLATION DU PANNEAU DE GRILLE INSTALLATION POUR : 1. Positionner le panneau de grille entre les supports de grille situés de chaque côté de l’armoire. 2. Accrocher le haut de la grille sur les rivetsgoupilles. Faire tourner vers le bas et pousser le bas du panneau de la grille dans l’appareil jusqu’à ce que le panneau de la grille s’emboîte.
INSTALLATION MARQUER LES EMPLACEMENTS DES SUPPORTS SUPÉRIEURS DES PANNEAUX INSTALLATION POUR : 6 3/4" (17,2 cm) A B C A. Haut du panneau de porte personnalisé du réfrigérateur B. Gabarit de perçage C. Bas du panneau de porte personnalisé du réfrigérateur 40 | INSTALLATION IMPORTANT : Pour une installation en armoire, au lieu de percer des trous le long du bord supérieur des panneaux, le gabarit de perçage (fournies avec le réfrigérateur) doit être placé correctement.
INSTALLATION INSTALLATION DES SUPPORTS ET DES RONDELLES À ÉPAULEMENT DU PANNEAU INSTALLATION POUR : Fixer le support supérieur du panneau de porte du réfrigérateur/congélateur au panneau de porte personnalisé en bois au moyen de vis pointues à tête hexagonale (2) aux emplacements de vis marqués (voir la section “Marquer les emplacements des supports supérieurs des panneaux”). A 2. Pour marquer l’emplacement des rondelles à épaulement, mesurer ‘A’ du haut du panneau, mesurer ‘B’ du côté du panneau.
INSTALLATION ! INSTALLATION DES SUPPORTS DU CONGÉLATEUR POUR LES MODÈLES CÔTE À CÔTE – PASSER CETTE ÉTAPE INSTALLATION POUR : A 2" (52,77 mm) 5 5/8" (143,3 mm) 4 7/8" (123,4 mm) 5 5/8" (143,3 mm) 42 | INSTALLATION 1. Pour marquer l’emplacement des vis du support du congélateur, mesurer ‘A’ à partir du haut du panneau. Marquer l’emplacement des trous comme indiqué à la figure. Consulter le tableau 2 pour connaître les dimensions de ‘A’ selon le modèle. 2.
INSTALLATION ! INSTALLATION DU PANNEAU DE CONGÉLATEUR POUR LES MODÈLES CÔTE À CÔTE – PASSER CETTE ÉTAPE INSTALLATION POUR : 1 Desserrer légèrement les vis de support du panneau du congélateur. REMARQUE : S’assurer que les portes du réfrigérateur sont bien fermées. 2. Glisser le panneau sur le tiroir. Serrer les quatre vis de chaque côté pour fixer le support au panneau du tiroir. 3. À l’aide des vis plates à tête cruciforme, fixer les supports du panneau au tiroir. 4.
INSTALLATION INSTALLATION POUR : INSTALLATION DES PANNEAUX DE PORTE WARNING 1 Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Install secondary anti-tip board to ensure product stability. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury. 2 REMARQUE : S’assurer que le panneau antibasculement secondaire est installé avant d’ouvrir la porte.
INSTALLATION INSTALLATION DES PANNEAUX DE PORTE (SUITE) AVERTISSEMENT Risque du poids excessif Utiliser deux personnes ou plus pour déplacer et installer les panneaux. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. Aligner les deux rondelles à épaulement à l’arrière du panneau de porte avec les fentes en “J” sur le côté de la porte du réfrigérateur. 5.
INSTALLATION DÉPLACEMENT DU RÉFRIGÉRATEUR À L’EMPLACEMENT FINAL INSTALLATION POUR : AVERTISSEMENT Risque du poids excessif Utiliser deux ou plus de personnes pour déplacer et installer le réfrigérateur. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. 1 A A. Niveau A B A.
INSTALLATION AJUSTER L’OUVERTURE DE LA PORTE INSTALLATION POUR : 1. Si l’ouverture standard de 110° de la porte est trop large, ajuster la goupille de butée de porte pour obtenir un débattement maximal de 90° de la porte. Insérer la goupille de butée de porte dans la charnière supérieure, au trou indiqué. À l’aide d’une clé hexagonale de 5/32", serrer la goupille de butée de la porte.
INSTALLATION ! AJUSTER LE PANNEAU DE CONGÉLATEUR POUR LES MODÈLES CÔTE À CÔTE – PASSER CETTE ÉTAPE INSTALLATION POUR : 1. io la at t Ins l nB k oc 1/8" 48 | INSTALLATION 1 L’espace entre le panneau et les armoires adjacentes doit être de 1/8" (3,2 mm). Utiliser la cale d’installation pour mesurer les espaces.
INSTALLATION AJUSTER LE PANNEAU DE RÉFRIGÉRATEUR INSTALLATION POUR : Desserrer légèrement les vis du support de panneau pour permettre au panneau de bouger de gauche à droite. 2. Ajuster les panneaux pour obtenir un espace de 1/8" (3,2 mm) entre les panneaux et les armoires adjacentes. Pour les modèles avec porte à double battant et congélateur en bas, aligner les bords extérieurs du panneau du réfrigérateur avec les bords extérieurs du panneau du congélateur des deux côtés.
INSTALLATION AJUSTER LE PANNEAU DE RÉFRIGÉRATEUR (SUITE) INSTALLATION POUR : A A 4 A. Tige d’ajustement 1/8" Ins 5 tall 50 50 || INSTALLATION INSTALLATION atio nB loc k 4. Utiliser une clé hexagonale de 5/32" pour élever ou abaisser les tiges d’ajustement afin de monter ou descendre le panneau de porte. 5. L’espace entre le panneau et le bas du soffite doit être de 1/8" (3,2 mm).
INSTALLATION FIXER LES PANNEAUX INSTALLATION POUR : 1. 1 À l’aide des vis à tête hexagonale fendue, fixer les charnières supérieure et inférieure aux panneaux de porte. Bien serrer toutes les vis du panneau de porte. REMARQUE : Ne pas trop serrer les vis pour ne pas endommager le panneau. 2. Pièces à utiliser : A Vis à tête hexagonale fendue (au besoin) B 2 C C A. Charnière supérieure B. Support de montage C. Trous pour les vis D E D. Tiges d’ajustement de porte E.
INSTALLATION FIXER LES PANNEAUX (SUITE) 3. Utiliser les vis à tête cruciforme pour fixer le panneau à la porte, sur le côté charnières. 4. À l’aide des vis à tête hexagonale fendue, fixer le support de montage, situé en bas des portes, aux panneaux.
INSTALLATION TERMINER L’INSTALLATION INSTALLATION POUR : 1. 2. 3. 1 Replacer les couvre-charnières. Emboîter les caches des tiges d’ajustement. Au moyen des vis à tête cruciforme, fixer les garnitures côté poignées (fournies avec le réfrigérateur) aux portes.
NOTES: 54 | INSTALLATION
NOTES: INSTALLATION INSTALLATION | 55
/™ ©2018 JennAir. Used under license in Canada. All rights reserved. Utilisé sous licence au Canada. Tous droits réservés.