VM9511TS Instruction Manual Manual de Instrucciones Guide d'instructions
CONTENTS TABLE DES MATIÈRES Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver for maximum enjoyment. Merci d'avoir choisi un produit Jensen . Nous espérons que vous allez trouver les instructions dans ce guide de propriétaire claires et faciles à suivre .
VM9511TS PREPARATION Congratulations on your purchase of the Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9511TS installed by a reputable installation shop.
VM9511TS WARNING! Never use irregular discs. WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor. WARNING! Do not change the fuse on the power wire without professional guidance. Using an improper fuse may cause damage to the unit and result in a fire. WARNING! The monitor employs an automatic motorized mechanism. To prevent damage to the core mechanism, please do not push, pull or swivel the monitor manually.
VM9511TS WIRING DIAGRAM 3
VM9511TS WIRING DIAGRAM - MULTIMEDIA CONNECTIONS *TERK XMDJEN100 cables (sold separately) **TERK XMD1000 Direct Tuner and antenna (sold separately) ***NAV100 (sold separately) 4
VM9511TS INSTALLATION Pre-installation 1. 2. Press the metal levers on both sides to remove the halfsleeve from the radio. Remove the transport screws. FINAL INSTALLATION CAUTION! Be careful not to damage the car wiring. 4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Wiring PREPARE RADIO Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal.
VM9511TS CONTROLS AND INDICATORS Button Operation 1. OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. WIDE/ PICTURE Press to adjust the display aspect of the picture to one of three settings: Cinema, Full, Normal or OFF. Press and hold to access picture settings. 3. ( ) Press to adjust the upward tilt angle of the screen one step at a time.
VM9511TS CONTROLS AND INDICATORS 10. 3/SCN DVD Mode: Press once to start scan playback. TUNER Mode: Press once to play preset radio station channel 3. Press and hold to store the current radio station in preset channel 3. 11. 4/RPT DVD Mode: Press once to start repeat playback. TUNER Mode: Press once to play preset radio station channel 4. Press and hold to store the current radio station in preset channel 4. 12. 5/2-6CH/RDM DVD Mode: Press once for random playback.
VM9511TS CONTROLS AND INDICATORS LCD Display/Indicators 1. Disc Indicator Illuminated when disc is loaded 2. DVD Playback Indicators (SCN/RPT/RDM/ALL) The following DVD playback indicators become Illuminated when the corresponding function is active: • • • • SCN: scan playback RPT: repeat playback RDM: random playback ALL: playback all chapters 1 2 3 3. Loudness Indicator (LOUD) The loudness indicator becomes illuminated when the LOUD function is activated. 4.
VM9511TS FRONT ZONE REMOTE CONTROL NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.
VM9511TS Table 1: Front Zone Remote Control Functions Button Name Function Ref# DVD VCD TUNER CD/MP3 TV XM Displays XM Setup Menu iPod MENU 1 Enters the main menu of the disc Turns on PBC when playing VCD Selects Photo mode TITLE 2 Enters the title menu of the disc Plays first ten seconds of each chapter/title MUTE 3 Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output
VM9511TS Table 1: Front Zone Remote Control Functions Button Name GOTO Function Ref# DVD VCD TUNER CD/MP3 TV XM iPod 21 Goes to specific time frame and playback Goes to specific time frame and playback 22 Slow playback/slow rewind playback Slow playback/slow rewind playback ZOOM 23 Zooms in/out on an image Zooms in/out on an image PIC 24 Displays set-up parameters Displays set-up parameters OPEN/ CLOSE 25 Opens/closes the TFT monitor Opens/closes the TFT monitor Opens/closes the T
VM9511TS MULTI-ZONE REMOTE CONTROL Table 2: Multi-Zone Remote Control Functions Button Name Function Ref # DVD VCD MENU 1 Enters the main menu of the disc Turns on PBC when playing VCD TITLE 2 Enters the title menu of the disc Plays first ten seconds of each chapter/title Toggles on/off audio output MUTE 3 Toggles on/off audio output AUDIO 5 Switches the audio language for disc playback REPT 7 Setup to repeat playback of each chapter/title/disc Setup to repeat playback of each chapter/t
VM9511TS USING THE TFT MONITOR Open/Close TFT Monitor Aspect Ratio Open TFT Monitor Press the DISP button (28) on the remote control or WIDE/ PICTURE button (2) on the monitor to adjust the aspect ratio as follows: Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to activate the mechanism that moves the display panel into the viewing position. CINEMA The entire screen is extended horizontally to the aspect ratio of 16 to 9.
VM9511TS d. Video should be displayed on the TFT monitor within 1 ~ 2 seconds.
VM9511TS OPERATING INSTRUCTIONS Power On / Off Press the /MUTE button (7) to turn the unit on. The buttons on the front of the unit light up and “WELCOME” appears briefly in the LCD panel (23), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the /MUTE button (7) on the front panel or the POWER button (4) on the remote to power off the unit.
VM9511TS SYSTEM SETUP MENU In “System Setup” mode, “ASP CONFIG” and “GENERAL SETUP” are available for adjustment. Setup can be performed by pressing the dedicated button on the remote control or by touching the top left corner of the TFT screen. For system settings, press the SYS SETUP button (31) on the remote control or touch “SETUP” on the screen to enter the “SETUP” menu. “SYS SETUP” is highlighted in green.
VM9511TS Returning to the System Setup Menu To return to the System Setup menu, move to “BACK”, then press the >/|| button (18) on the remote control. ASP (Audio Sound Processing) Config Menu The ASP Config Menu allows you to make fine audio adjustments. button (16, 17) on the joystick. The new value is highlighted in light blue and setup is complete.
VM9511TS MULTI-ZONE OPERATION Independent sources can be played simultaneously on the VM9511TS. For example, a video game console can be seen on the front screen while DVD video is available to rear passengers. NOTE: If DVD is selected as the front source and SD Card is selected for the rear source, then both sources will switch to SD Card. If SD Card is selected as the front source and DVD is selected for the rear source, then both sources will switch to the DVD source.
VM9511TS TUNER OPERATION Tuner TFT Display Alternate TFT Tuner Display Using Preset Stations Default TFT Tuner Display The VM9511TS offers an alternate display for the AM / FM tuner interface that is less bright than the default tuner display and is more appropriate for night driving. Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen. Storing a Station 1. Select a band (if needed), then select a station. 2.
VM9511TS XM RADIO OPERATION Listeners can subscribe to XM® Radio on the Web by visiting www.xmradio.com, or by calling (800) 967-2346. Customers should have their Radio ID ready (see “Displaying the Identification (ID) Code”). Customers can receive a limited number of free-to-air channels without activation. Accessing XM® Radio Mode Press the SRC button (15) on the front panel or remote control (8) to switch to the XM source. 17. MENU: Access the XM Setup Menu 18.
VM9511TS unit, remote control, or touch screen. The channel will begin playing and the unit will return to the Preset Mode. While in Preset Mode, press and hold an on-screen preset button (or 1-6 on the unit or remote control) to store the channel playing. Category Guide Mode When Category Mode is selected, “Search Mode” and “CATEGORY” appear in the top half of the user interface. Press the TITLE button (2) to return to the Category Mode main page and select a different category.
VM9511TS DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “PARKING” with a blue background. Rear video screens, if applicable, will operate normally. Using the Touch-Screen Controls The touch key areas for DVD playback are outlined below. NOTE: For VCD play, the repeat function is not available if PBC is on.
VM9511TS Fast Forward/Fast Reverse • Press the >> button (14) on the remote control or the /\ button (18) on the joystick to fast forward. Keep pressing and releasing the button to increase the rate from “2X” to “4X”, “8X”, and “20X”. Continue pressing the >> or /\ button to fast reverse. For DVD mode, you can choose Time or Title/Chapter search.
VM9511TS • 2 / 6 Eng – The language display information indicates the second language out of 6 (English) is currently being used. The following information appears at the bottom of the screen during DVD playback: Front: DVD/CD Rear: AUXIN • • Dolby Digital Bypass Front: DVD is the current playback source for the front zone. Rear: AUX IN is the current playback source for the rear zone. "Dolby Digital" is the selected playback audio encoding process.
VM9511TS DVD/DISC SETUP MENU NOTE: A DVD/disc must be loaded into the mechanism and playing prior to accessing the DVD Setup menu. While the DVD/disc is playing, press the DVD SETUP button (30) on the remote to access the DVD Setup menu. can also touch the on-screen menu selection to access that menu. DIRECTION BUTTONS In “DVD Setup” mode, “LANGUAGE”, “VIDEO”, “AUDIO” “SPK CONFIG”, “PRO-LOGIC II”, and “RATING” (parental lock) are available for setup.
VM9511TS AUDIO Menu SPK CONFIG Menu Table 16: SPK CONFIG Menu Features The VM9511TS has a built-in Pink Noise generator to help set the relative speaker levels for multi-channel audio playback.
VM9511TS Table 17: Pro-Logic II Menu Features Setting Options Decode Mode Function Table 18: RATING Menu Features Setting Off Play original audio format. Pro-Logic II Use Pro-Logic II decoding method. Pro-Logic II Matrix Play mono output with surround effect. 4. PG-13 Pro-Logic II Movie Enhance movie surround effects. 5. PG-R Pro-Logic II Music Play surround music effects. Panorama (Only available when Pro-Logic II Music Mode is selected.
VM9511TS DVD/DISC AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD, CD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9511TS will play music or other audio files from the following disc media: • • • • CD-DA CD-R/RW with MP3 or WMA files DVD DVD-R/RW with MP3 or WMA files 13. 14. 15. 16. 17. 18. 19.
VM9511TS NOTE: When burning MP3 / WMA files onto a DVD disc, use the 2X or 4X burning option, if available. This slower burning speed will help eliminate buffer errors and increase disc reading reliability. Also, use folders when burning large numbers of songs / files to a disc for easy music navigation. Select the "Disc at Once" option and close your disc.
VM9511TS SD CARD READER OPERATION Accessing SD Card Mode Moving Through Chapters To switch to SD card mode, press the SRC button (15) on the front panel. Press the >>| button (19) on the remote control or the > button on the joystick (17) to advance to the next chapter. Using the Touch-Screen Controls Press the |<< button (17) on the remote control or the < button on the joystick (16) to move to the previous chapter. The touch keys for SD card playback are described below.
VM9511TS IPOD OPERATION Accessing iPod Mode The unit will automatically switch to iPod mode when an iPod is plugged into the media module. To return to the iPod menu from any other source menu, press the SRC button (15) on the front panel or remote control (8) until the iPod menu appears on the screen. Press the AUDIO button (5) on the remote control to access the iPod VIDEO mode. The VM9511TS will release control back to the iPod so you can select video media to be displayed on the VM9511TS TFT monitor.
VM9511TS TV TUNER OPERATION Accessing TV Mode To switch to TV mode, press the SRC button (15) on the front panel or on the remote control (8) until “TV” appears at the bottom of the screen. Seek Tuning Press the >>| button (19) on remote control, or the > button on the joystick (17) to seek the next available TV station by increasing the tuning frequency.
VM9511TS NAVIGATION SYSTEM The VM9511TS is "navigation ready." Before accessing any navigation features, you must purchase and install the NAV100 module. All installation and operating instructions will be included with the NAV100 navigation module. Once the NAV100 is connected and operating properly, the NAVI source mode will become active. While the NAV100 is not installed, the NAVI option appears gray, indicating the function is not available.
VM9511TS TROUBLESHOOTING Table 19: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on Remote control does not function No/low audio output Poor sound quality or distortion Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right corner of the front panel Battery depleted Replace battery with new one Battery installed incorrectly Remove batt
VM9511TS Table 19: Troubleshooting Problem Disc does not play back Cause Corrective Action Disc is warped or scratched Use disc in good condition Disc is dirty or wet Clean disc with soft cloth Laser pickup is dirty Clean laser pickup with cleaning disc Incompatible disc is used Use compatible disc Disc rating exceeds Parental Lock rating limit Change Parental Lock settings to lower restriction Disc region code is not compatible with unit Use disc with proper region code Disc is inserted upsi
VM9511TS Care and Maintenance 1. 2. 3. 4. 5. 6. 7. 8. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and nonneutral detergent (such as alcohol) may result in scratching or discoloration. Do not get water or cleaning fluids on the unit. If the temperature inside the player gets too hot, a protective circuit automatically stops play of the disc. If this occurs, allow the unit to cool before operating the player again.
VM9511TS SPECIFICATIONS CEA Power Ratings Main Amplifier Power Output: 18 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms) Dynamic Power: 88 watts into 4-ohms, all channels driven Frequency Response: 20Hz to 20kHz, -3dB. Aux input used as source reference Reference Supply Voltage: 14.
