LED TV User’s Guide Please observe all safety precautions when using this product. English 14 SERIES Guide de l’utilisateur du téléviseur LED Veuillez observer toutes les mesures de sécurité en utilisant ce produit. Veuillez lire soigneusement ce manuel avant d’utiliser ce produit. Français Please read this manual carefully.
CONTENTS Safety Precautions Important Information .................................................................................... 3 Important Safeguards ................................................................................. 4 - 5 User Guidance Information Part identification (Right View) / Accessories ....................................................... 6 Part identification (Back View) ....................................................................
Important Information WARNING IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire or electric shock,do not expose this product ot rain or moisture. 1) 2) 3) 4) 5) 8) This symbol is intended to alert the user to the presence of uninsulated “ dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of 9) electric shock to persons.
Important Safeguards Before using your TV, please read these instructions completely, and keep this manual for future reference, Carefully observe and comply with all warnings, cautions and instructions placed on the unit or described in the operating instructions or service manual. WARNING To guard against injury, the following basic safety precautions should be observed in the installation, use and servicing of the unit.
Important Safeguards Do not use near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. Do not use immediately after moving from a low temperture to high temperature environment, as this cause condensation, which may result in fire, electric shock, or other hazards. This product should not be exposed to dripping or splasing and no objects filled with liquids, such as vases, should be placed on the product.
User Guide Information Part Identification Right View SOURCE Button VOL+ / VOL- Button MENU Button-OSD Menu Display Button POWER Button CH+/ CH- Button English Accessories The configuration of the omponents may look different from the following illustration.
Part Identification Back View 2 2 3 4 2 6 5 7 8 n 1 E JE3214 & JE3914 7 6 1 4 2 3 5 8 English s i l g JE1914 9 1 4 7 10 1. AUDIO (L/R) OUT 2. HDMI 1 / HDMI 2 / HDMI 3 INPUT 2 3. PC IN (VGA and AUDIO) INPUT 4. USB Port 8 5. Y Pb Pr INPUT 6. AV IN ( VIDEO and AUDIO) 7. SPDIF OUTPUT 8. RF IN 9.
User Guide Information Mounting on a Desktop Your LED TV can be mounted on a desktop with the base installed. This is not a floor-standing unit. Installation Precautions Wall Mounting Please ensure enough space for safe use. Please refer to diagrams A and B. Installation of the LED TV in an improperly ventilated location can cause damage to the LED TV due to increased temperature.
User Guide Information Installing an Antenna For connecting to ATS or NTSC broadcast Use a coaxial cable to connect the wall jack or external antenna to the RF-IN on the LED TV. Wall Jack with F-Connector Coaxial (Round) Antenna Cable Analog+Digital 75 English Press the SOURCE button on the remote control to select TV, then press RIGHT button to confirm. Then you can receive the ATSC/NTSC signal. See page 17 for initial setup.
User Guide Information Remote Control Funtions of remote control buttons 1 3 2 1 TV Activate TV Mode 2 POWER On / off for TV and DVD 3 DVD Activate DVD Mode PREVIOUS FAST REVERSE FAST FORWARD NEXT EJECT(DVD) STOP PLAY/PAUSE Repeat Selection RPT T/F (DVD) ZOOM (DVD) 4 4 5 6 7 8 9 10 11 12 13 14 15 5 6 7 8 9 10 16 20 24 28 18 17 19 11 12 21 22 25 26 29 23 13 14 27 15 16 30 17 18 31 19 20 32 21 33 22 23 35 34 37 24 36 25 26 38 27 English 28 29 30 31 39 4
User Guide Information Remote Control BUTTON TV-FUNCTION DVD-FUNCTION BUTTON TV-FUNCTION DVD-FUNCTION BUTTON TV-FUNCTION DVD-FUNCTION POWER CH CH+ CH- VOL VOL+ VOL- RETURN MUTE MENU INFO POWER EPG EPG T-F T F VOL+ VOL- EJECT RETURN MUTE MUTE 1 1 1 MENU MENU 2 2 2 3 3 3 INFO UP 4 4 4 DOWN DOWN 5 5 5 LEFT LEFT 6 6 6 RIGHT RIGHT 7 7 7 ENTER ENTER OK 8 8 8 SOURCE SOURCE SOURCE 9 9 9 0 0 0 EXIT PLAY-PAUSE PLAY-PAUSE PREVIOUS PREVIOUS FAST-FORWARD
User Guide Information Precautions Avoiding Remote Control Problems 1. Check the polarity (+,-) of the batteries in the remote control. 2. Check that the batteries are good. Inserting Batteries in the Remote Control 1. Open the cover completely. 2. Insert the two supplied batteries (AA, 1.5V). Ensure that the polarities (+ and -) of the batteries are aligned correctly. 3. Replace the cover. English CAUTION: Risk of explosion if battery is replaced by incorrect type.
VCR Connections Connecting to the Composite terminal Terminals vary by manufacturer Composite Cable (Included) Connect the LED TV’s Composite In terminal to VCR’s Composite OUT terminal using the included Composite cable. (Make sure the color of the terminals and the colors of the cable are the same.) Digital Amplifier Connections Connecting to a Digital Amplifier Terminals vary by manufacturer. Digital Amplifier English SPDIF Cable (Not Included) Watching Video Tape 1.Turn on the LED TV and press 2.
Satellite / Cable TV Set-Top Box Connections Connecting to the Composite terminal In order to watch Cable TV, Subscribe to your local Cable TV company and install a separate receiver (Set-Top Box) Terminals vary by manufacturer (Included) Connect the LED TV’s Composite In terminal to the cable broadcasting receiver Composite Out terminal using the Composite cable.
Connection DVD Connections Connecting to the component terminal Terminals vary by manufacturer (Not Included) Component Video Cable (Not Included) 1. Connect LED TV’s YPbPr terminal to DVD’s Video Out terminal. 2. Connect LED TV’s Audio terminals in YPbPr to DVD’s Audio Out terminal. 3. It must match the component connection cable Y, Pb, Pr colors between the LED TV and DVD Player. Connecting to the HDMI terminal HDMI Cable(Not Included) USB Connections English Connection to USB.
PC Connections Terminals vary by manufacturer. VGA Cable (Not Included) PC Audio Cable (Not Included) Connect the LED TV’s PC Input terminal to the PC’s VGA terminal using a VGA cable. Connect the LED TV’s PC Audio terminal to the PC’s Audio terminal using a 3.5mm (Headphone) audio cable. (Only for PC’s with an Audio termianl) External Audio Amplifier Connecting to an amplifer or home theater system. Terminals vary by manufacturer.
Selecting Input Source You can select between the TV signal and the input signal of other equipment connected to the TV. Use this function to switch to the input source you wish to view. Press button on the remote control. Use to move to the desired input source. INPUT SOURCE SOURCE INPUT Press TV AV Component HDMI1 HDMI2 HDMI3 VGA USB to select. Note: After you have selected the desired input sorce and pause for a few moments, then LED TV will automatically enter the seleted mode.
Application Menu Operation Press the POWER button to turn the LED TV on. Press the MENU button on the remote control, the on-screen menu will appear. Use the LEFT and RIGHT buttons to select your main menu option. PICTURE MENU: AUDIO MENU: Allows you to make adjustments to your picture settings. Allows you to customize the sound options and effects.
Application Customizing the PICTURE Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT buttons to select the PICTURE. 3. Use the UP and DOWN buttons to highlight an individual PICTURE options, use the LEFT and RIGHT buttons to change the setting, and press the MENU or EXIT button to exit.
Application Customizing the Audio Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on. 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT buttons to select the AUDIO. 3. Use the UP and DOWN buttons to highlight an individual Audio options, use the LEFT and RIGHT buttons to change the setting, and press the MENU or EXIT button to exit.
Application Customizing the TIMER Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on. 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT buttons to select the TIMER. 3. Use the UP and DOWN buttons to highlight an individual TIMER option, use the LEFT and RIGHT buttons to change the setting, and press the MENU or EXIT button to exit.
Application Customizing the SETUP Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on. 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT or RIGHT button to select SETUP. 3. Use the UP and DOWN buttons to highlight an individual SETUP option, use the LEFT and RIGHT buttons to change the setting, and press the MENU or EXIT button to exit.
Application Customizing the SETUP Settings Closed Caption Use Down button to highlight “Closed Caption”, then press RIGHT button or ENTER to enter into the following menu. 12 6 Audio Picture Time Setup Lock CC Mode On Basic Selection CC1 Advanced Selection Channel Service1 Option Move Select MENU Return CC Mode Allows you to select the CC Modes: On, Off and CC on Mute. Basic Selection Allows you to select the basic selections: CC1, CC2, CC3, CC4, Text1, Text2, Text3 and Text4.
Application Customizing the LOCK Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT buttons to select the LOCK 3. Use the DOWN button to highlight “Enter Password” , use the numeric keys to input a 4-digit password. After that, the screen will display the next menu. After setting, press menu or exit button to exit.
Application Customizing the LOCK Settings Use Down button to highlight “US” , then press RIGHT or ENTER button to enter into the following menu. 12 6 Audio Picture Time Setup Lock Channel TV MPAA Move TV N A NEXT MENU Return Use Down button to highlight “TV” , then press RIGHT or ENTER button to enter into the following menu.
Application Customizing the LOCK Settings Canada Use the Down button to highlight “Canada”, then press the RIGHTor ENTER button to enter into the following menu.
Application Customizing the CHANNEL Settings Select TV source for example. (Press SOURCE button to select TV mode) 1. Press the POWER button to turn the LED TV on. 2. Press the MENU button on the remote control to display the Main menu, and use the LEFT and RIGHT buttons to select the CHANNEL. 3. Use the UP and DOWN buttons to highlight an individual CHANNEL option, use the LEFT and RIGHT buttons to change the setting, and press the MENU or EXIT button to exit.
Application Customizing the CHANNEL Settings If you select “Cable” as input signal in Antenna then you can select Cable Systems: Auto, STD, IRC and HRC. Use DOWN button to highlight “Start to Scan”, then press the RIGHT or ENTER button to search the channels automatically. The receivable channels will be stored automatically. When searching channels, press MENU to stop. Favorite Allows you to add these channels as the favorite channels.
Application USB Settings This TV is a widescreen TV with USB port. Through the USB port the TV can access USB flash drives and display pictures or play MP3 files. To use this feature connect a USB flash drive to the USB port of the TV and press the SOURCE button to select USB to start browsing for music and pictures. In the USB Mode, select Photo USB Photo C: Music C:\ mblog.jpg mblog.jpg Play File:1 001/001 Total size:2.0GB Unused size:1.8GB 534 x 800 Select Move 34.
Maintenance and Service Trouble shooting In case a problem occurs with your LED TV, please take the following steps first. If you still have the problem, turn the power off and contact your dealer or an authorized service center. Problem Action The screen does not appear. Is the power plug connected? Insert the power plug. Press the power button of the remote control. The screen appears too slowly after the power is turned on.
Maintenance and Service Specifications LED Panel Panel Size 31.5” TFT LED Brightness 200 Contrast Ratio 4000:1 Viewing Angle 1780/1780 Max. Resolution INPUT OUTPUT 1366 x 768 VIDEO 1 AUDIO (L/R) 1 PC/AUDIO(L/R) 1 HDMI 3 RF 1 YPbPr 1 AUDIO (L/R) 1 SPDIF 1 Power Source AC 100-240, 50/60Hz Power Consumption 50 W 39” TFT LED 1920 x 1080 70 W Dimension 733W x 503H x 80D mm 889W x 582H x 89D mm Weight 6.
Maintenance and Service Specifications LED Panel Panel Size 18.5” TFT LED Brightness 200 Contrast Ratio 1000:1 Viewing Angle 1700/1600 Max. Resolution INPUT OUTPUT 1366 x 768 VIDEO 1 AUDIO (L/R) 1 PC/AUDIO(L/R) 1 HDMI 1 RF 1 YPbPr 1 AUDIO (L/R) 1 SPDIF 1 Power Source AC 120V Power Consumption 25 W Dimension 458W x 344H x 156D mm Weight 3.5 Kg English The cabinet design and electronics specifications may be modified without prior notice for performance improvement.
CONTENUS Précautions de Sécurité Informations importantes ....................................................................................3 Mesures importantes de sécurité........................................................................4 - 5 Information guide de l’utilisateur ....................................................... 6 Noms de chaque élément (Vue en face) / Accessoires Noms de chaque élément (Vue arrière)....................................................................
Information Important INSTRUCTIONS IMPORTANTES DE SECURITE 1) 2) 3) 4) 5) Lire ces instructions. Garder ces instructions. Observer tous les avertissements. Suivre toutes les instructions. N’utiliser pas ce produit près de l’eau. L'appareil ne devrait pas être exposé aux projections ou aux éclaboussures et aucun objet rempli de liquide, tels que des vases, ne devraient être placé sur le produit. 6) 7) Nettoyer uniquement avec un tissu sec. Ne bloquer aucune ouverture de ventilation.
Mesures de sécurité importantes Avant de vous servir de votre téléviseur, veuillez lire entièrement ces instructions, et gardez ce manuel pour une future référence. Observez et respectez soigneusement tous les avertissements, et les instructions placés sur l'unité ou décrits dans les instructions d’opération ou le manuel d'entretien.
Mesures de sécurité importantes Sources de chaleur N’utiliser pas ce produit près de l’eau Ne l’employez pas près d´une baignoire, d´un lavabo, de l´évier de cuisine ou d´un baquet à laver, dans un sous-sol humide ou près de la piscine.
Information guide de l’utilisateur Noms de chaque élément Vue de face Bouton de source Bouton de Volume +, - Bouton de menu – Bouton d’affichage de Menu OSD - Bouton d’alimentation Bouton de Canal / Programme +,- Accessories La configuration des composants peut sembler différente de l’illustration suivante.
Information guide de l’utilisateur Noms de chaque élément Vue arrière JE3214 & JE3914 1 2 2 3 4 2 6 5 7 8 JE1914 1 4 2 3 5 8 9 a r 6 is a ç n 1. Audio (gauche / droit) sortie 2. Cric de HDMI1 / HDMI2 / HDMI 3 3. VGA et Ordinateur Audio 4. Cric de USB 5. Y Pb Pr 6. AV entre (Video et Audio) 7. SPDIF 8. RF (ATSC/NTSC) 9.
Information guide de l’utilisateur Montage sur table Votre téléviseur LED peut être monté sur une table avec le sommier installé. Ce n’est pas une unité à poser par terre. Précautions d’installation Support mural Veuillez garantir l’espace suffisant pour l’utilisation en sécurité.(Veuillez vous référer à A et B). L´installation du téléviseur LED dans un endroit incorrectement aéré peut causer endommager le téléviseur LED en raison de la hausse de température.
Information guide de l’utilisateur Installation d’une antenne Pour connecter aux transmissions ATSC ou NTSC Prise murale avec le connecteur F Câble coaxial (rond) d’antenne Analogue + Numérique 75 Ω Antenne externe Français Appuyez sur le bouton SOURCE de la télécommande pour sélectionner TV, appuyez ensuite sur le bouton RIGHT pour confirmer. Après vous pouvez recevoir le signal d’ATSC/NTSC.
Information guide de l’utilisateur Télécommande Fonctions des boutons de la télécommande 1 3 2 1 TV Activez le mode de TV 2 POWER Marche/ Arrêt pour le téléviseur et le DVD 3 4 4 5 6 7 8 9 10 11 12 13 14 15 5 6 7 8 9 10 16 20 24 28 18 17 19 11 12 21 22 25 26 29 23 13 14 27 15 16 30 17 18 31 19 20 32 21 33 22 23 35 34 37 24 36 25 26 38 27 28 29 30 31 39 40 32 33 Français 34 35 36 37 38 39 40 10 Activez le mode DVD DVD PREVIOUS rapide – retour en ar
Information guide de l’utilisateur Télécommande BUTTON TV-FUNCTION DVD-FUNCTION BUTTON TV-FUNCTION DVD-FUNCTION BUTTON TV-FUNCTION DVD-FUNCTION POWER POWER CH CH+ CH- VOL VOL+ VOL- RETURN RETURN MUTE MUTE POWER EPG INFO T-F T F VOL+ VOL- EJECT STOP PLAY-PAUSE PLAY-PAUSE PREVIOUS PREVIOUS FAST-REVERSE FAST-REVERSE MUTE 1 1 1 2 2 2 3 3 3 RPT MENU MENU STOP EPG MENU INFO FAST-FORWARD FAST-FORWARD NEXT NEXT RPT RPT UP UP 4 4 4 ZOOM ZOOM DOWN DOWN 5 5 5 SU
Information guide de l’utilisateur Précautions Eviter les problèmes avec la télécommande 1. Vérifier la polarité ( +, -) des piles dans la télécommande. 2. Vérifier que les piles sont bonnes. Insérer les piles dans la télécommande 1. Ouvrer la couverture complètement. 2. Insérer les deux piles d’alimentation fournies (AA, 1.5V) Assurez-vous que les polarités (+ et -) des piles sont alignées correctement. 3.
Raccordement Raccordement de VCR ● Connexion aux composants de sortie Les bornes peuvent varier en fonction du fabricant Câble composé (Inclus) Connecter la borne In composite du téléviseur LED à la borne Out en utilisant le câble composé inclus (s´assurer que la couleur des terminaux et la couleur du câble sont les mêmes) Raccordement d’amplificateur numérique ● Raccordement à l’amplificateur numérique Les bornes peuvent varier selon le fabricant Câble SPDIF (non inclus) Voir
Raccordement Connexion des bornes supérieures du téléviseur câble/satellite ● Raccordement aux composants de sortie Pour regarder le téléviseur à l’aide d’un câble, souscrivez à la société locale du téléviseur de câble et installez un récepteur séparé (Boîte d’installation en haut) Les bornes varient selon les fabricants Récepteur d’annonce de Câble Câble composé (Inclus) ● Raccordement à la borne HDMI Récepteur d’annonce de Câble Câble HDMI (non inclus) Regarder la télévision grâce au câble Français
Raccordement Raccordements de DVD ● Raccorder à au composant de sortie. Les bornes varient selon le fabricant Câble audio (non inclus) Câble composé de Vidéo (non inclus) 1.Raccorder la borne de YPbPr du téléviseur LED à la borne de Sortie vidéo de DVD. 2 Raccorder la borne audio dans YPbPr du téléviseur LED à la borne de Sortie audio de DVD. 3.Entre le TÉLÉVISEUR LED et le lecteur de DVD il doit s’accorder avec le câble composé de raccordement de Y, Pb et Pr. ● Raccorder à la borne HDMI.
Raccordement Raccordement de l’Ordinateur Personnel Les bornes peuvent varier selon le fabricant. Câble de VGA (non inclus) Câble Audio d’ordinateur (non inclus) • • Raccorder la borne d’entrée d’ordinateur du téléviseur LED à la borne VGA d’ordinateur en utilisant un câble VGA. Raccorder la borne audio d’ordinateur du téléviseur LED à la borne audio d’ordinateur en utilisant un câble audio de 3,5mm (écouteur).
Utilisation de Base Sélection de la source d’entrée ● Vous pouvez choisir entre le signal du téléviseur et le signal d’entrée d’un autre appareil connecté au téléviseur. ● Utiliser cette fonction pour changer la source d’entrée que vous désirez voir. Appuyer sur la télécommande Utiliser pour aller à la source d’entrée souhaitée INPUT SOURCE SOURCE INPUT Appuyer TV AV Component HDMI1 HDMI2 HDMI3 VGA USB pour sélectionner.
Application Opération de menu 1. Appuyer sur le bouton « POWER » pour allumer le téléviseur LED. 2. Appuyer sur le bouton « MENU » de la télécommande, le menu de l’écran apparaît. 3. Utiliser les boutons « LEFT » et « RIGHT » pour sélectionner votre menu principal. Menu image: Menu audio: Vous permet d’ajuster les paramètres vidéo. (choisir la source téléviseur par exemple) Vous permette de personnaliser les options et les effets vidéo.
Personnalisation des paramètres de l’image Choisir la source téléviseur par exemple. (Appuyer sur le bouton SOURCE pour sélectionner le mode TV) 1. Appuyer sur le bouton de POWER pour allumer le TV à ACL 2.
Personnalisation des paramètres AUDIO Choisir source TV par exemple. (Appuyer sur le bouton SOURCE pour sélectionner le mode TV) 1. Appuyer sur le bouton POWER pour allumer le TV à ACL 2. Appuyer sur le bouton MENU de la télécommande pour montrer le menu principal, et utiliser les boutons LEFT et RIGHT pour sélectionner AUDIO 3.
Application Personnalisation des paramètres du TIMER Sélectionner source TV par exemple. (Appuyer sur le bouton SOURCE pour sélectionner mode TV) 1. Appuyer le bouton POWER pour allumer le TV à ACL 2. Appuyer sur le bouton MENU de la télécommande pour montrer le menu principal, et utiliser les boutons LEFT et RIGHT pour sélectionner le TIMER 3.
Application Personnalisation des paramètres de SETUP Choisir la source TV par exemple. (Appuyer sur le bouton SOURCE pour sélectionner le mode TV 1. Appuyer sur le bouton POWER pour allumer la TV à ACL 2. Appuyer sur le bouton MENU sur la télécommande pour montrer le menu principal, et utiliser les boutons de LEFT ou RIGHT pour sélectionner INSTALLATION 3.
Application Personnalisation des paramètres de SETUP Télétexte (CC) Utiliser le bouton DOWN pour surligner « Close Caption », appuyer ensuite sur le bouton RIGHT ou ENTER pour entrer dans le menu suivant. 12 6 Audio Picture Time Setup Lock CC Mode On Basic Selection CC1 Advanced Selection Channel Service1 Option Move Select MENU Exit Mode CC Vous permet de choisir les modes télétexte : Marche, Arrêt ou CC en muet.
Application Personnalisation des paramètres de verrouillage (LOCK) Choisir la source TV par exemple. (Appuyer sur le bouton SOURCE pour sélectionner le mode TV) 1. Appuyer sur le bouton POWER pour allumer la TV à ACL 2. Appuyer sur le bouton MENU de la télécommande pour montrer le menu principal, et utiliser les boutons LEFT et RIGHT pour sélectionner LOCK 3. Utiliser le bouton DOWN pour surligner « Saisir mot de passe », utiliser les clés numériques pour entrer un mot de passe de 4 chiffres.
Application Personnalisation des paramètres de verrouillage (LOCK) Utiliser le bouton DOWN pour surligner « US » (États-Unis), appuyer ensuite sur les boutons RIGHT ou ENTER pour entrer dans le menu suivant. 12 6 Audio Picture Time Setup Lock Channel TV MPAA Move N A NEXT MENU Exit Le Utiliser le bouton DOWN pour surligner « TV », appuyer ensuite sur téléviseur les boutons RRIGHT ou ENTER pour entrer dans le menu suivant.
Application Personnalisation des paramètres de verrouillage (LOCK) Canada Utiliser le bouton DOWN pour surligner Canada, appuyer ensuite sur le bouton RIGHT ou ENTER pour entrer dans le menu suivant.
Application Personnalisation des paramètres de CHANNEL (chaîne) Choisir la source TV par exemple. (Appuyer sur le bouton SOURCE pour sélectionner le mode TV) 1. Appuyer sur le bouton POWER pour allumer le TV à ACL. 2. Appuyer sur le bouton MENU de la télécommande pour afficher le menu principal, et utilisez les boutons LEFT et RIGHT pour choisir la chaîne (Channel). 3.
Application Personnalisation des paramètres de CHANNEL (chaîne) Si vous choisissez « Câble » comme signal d’entrée dans Antenna, vous pouvez choisir les systèmes de câble : Auto, STD, IRC et HRC Utilisez le bouton DOWN pour surligner ‘ »Start to Scan » (commencer le scan), appuyer ensuite sur les boutons RIGHT ou ENTER pour chercher automatiquement les chaînes Les chaînes pouvant être reçues seront gardées automatiquement. Lors de la recherche des chaînes, appuyez sur MENU pour arrêter.
Application Configuration USB Le téléviseur est un téléviseur à grand écran avec un port USB. Avec ce port USB, le téléviseur peut accepter les lecteurs flash USB et afficher les photos ou lire les fichiers MP3. Pour utiliser cette fonction, il faut connecter un lecteur flash USB au port USB du téléviseur et appuyer sur le bouton SOURCE pour sélectionner le mode USB afin de commencer la navigation de la musique et des photos. Dans la fonction USB, sélectionnez Photo USB Photo C: Music C:\ mblog.
Entretien et Service Dépannage Si votre TV à ACL présente un problème, veuillez avant tout suivre les étapes suivantes. Si vous avez encore le problème, éteignez l’appareil et contactez votre revendeur ou un centre de service autorisé. Problème Action L’écran n’apparaît pas. Est ce que la prise est branchée? Branchez la prise. Appuyez sur le bouton d’allumage de la télécommande. L’écran apparaît trop lentement après avoir allumé l’appareil.
Entretien et Service Spécifications Panneau de LED Grandeur de panneau 31.5” TFT LED L'éclat 200 Rapport contrasté 4000:1 L'angle de observation 178º/178º Max. résolution Entre Sortie 39” TFT LED 1366 x 768 Vidéo 1 Audio (gauche / droit) 1 PC/Audio (gauche / droit) 1 HDMI 3 RF 1 YPbPr 1 Audio (gauche/droit) 1 SPDIF 1 1920 x 1080 Source d'alimentation AC 100~240,50/60Hz Consommation d'alimentation 50W Dimension 733W x 503H x 80D mm 889W x 582H x 89D mm Poids 6.
Entretien et Service Spécifications Panneau de LED Grandeur de panneau 18.5” TFT LED L'éclat 200 Rapport contrasté 1000:1 L'angle de observation 170º/160º Max. résolution Entre Sortie 1366 x 768 Vidéo 1 Audio (gauche / droit) 1 PC/Audio (gauche / droit) 1 HDMI 1 RF 1 YPbPr 1 Audio (gauche/droit) 1 SPDIF 1 Source d'alimentation AC 120V Consommation d'alimentation 25W Dimension 458W x 344H x 156D mm Poids 3.
www.asaelectronics.com www.jensenrvdirect.