A222HLX Power Amplifier 2x50 WADS RMS POWER 2 CHANNEL INPUT SENSITIVITY CONTROL 2-8 OHM OPERATION HiGH/LOW LEVEL INPUTS Owner's Manual and Installation Instructions Technical Assistance For technical assistance with the operation Of installation of the A222HLX, call 1-800-323-0221
A222HLX Amplifier Thank You Thank you for buying a lensen product. Congratulations on your investment in quality sound reprOOuction for your car. ~ read this manual bcl.un: installation and operation. Easy Operation Jensen products are simple and easy to operate. This manual explains how to use the A2221-li..X for ma.ximum enjoyment. Installation For prop::r operation. it's w.ry important that tile unit be installed corrt:ctly.
A222HLX Amplifier General Information The Jensen A222HLX power amplifier is a (w(>-.Channel 25D-watt peak automotive amplifier. The A222HLX includes: • High-level in/X'ts (speaker level) • Low-level inputs (RCA phono) • Input sensitivity control • Remote tum onIoff • Electronic protection Circuitry to protect the amplifier from shon circuit, DC offset and thermal oVt:rio,ld • Unique. super-efficient ht:at sink dt:sign.
A222HLX Anlplifier Inputs Input Sensitivity Control Adjust the sensitivity to the inpullevd Crossover Adiust the crossover to accomoda\e your chosen installation method. • LPF==low pa~s filter • HPF==high pass filter • Flat::=no filter. See Installation Alternatives on page 5. Connect to speakers. High Level Input Harness Low Level Input RCA Connectors Connect RCA cables from YOOf receiver (if equipped) t(l these RCA jacks. For the least hamlOnic distortion, low level inputs are rc(;omnlcnJed.
A222HLX Amplifier Parts and Tools • For low level input connection you will need a pair of shielded Mert:O audio cables with RCA Supplied parts and fasteners: • A222HLX Amplifier type jacks. Tht;': length or the cabl<: and configuration of jacks depends on your particular installation. I r mountt;':d undt;':f tilt;': dash near lhe radio, you will nt;':t;':d a pair of shieldt:d audio cables. Keep tht;':se cables as short as possible to minimize the chance of picking up interference.
A222HLX AmpUf"Hllr Wiring Instructions This section explains how 10 wire the A222HLX power amplifier to your vehicle system. ImportEnt: If wiring connections are made wrong, the unit will not operate p{"ope{"iy and it could be damaged. Follow the installation instnlctions carefully, or have the installation handled by an experienced technician. Power Antenn.a Lead (fO sensing wire.
A222Hl.X AOlplifier - Troubleshooting CorrectM! Action Po$sible Cause No power to yekNi poy.e-..we ~doesrd~ ijxJwef LED rd al) ....oen vehOe and rociO are withvehOe(l') (l1 COed: cornect):;)ns to raio No power to bUe sensOg wire ~radoCf1 """"""" Fuse 00Ml (ioline ~, yelbN v.ire) I~ sensitivity axttrd aqusted too low A1rlo ;Ot,rne needs to be turned ~ too tij1 for ~ \ Rado rlrne is too seroitive ! Scu1d from c;d.
Specifications Amplifier 250 Watts Peak Poweroulpllt@ 14.4 VOC 1 kHL Frequency Response .. Signa.! to Noise Ratio @ Rateo Power. Channel Separation @ Ref. Power _,_ THO & IMO @ Ref. Power in[(l 2 ohms SrlCaker Impedance .... Inpullmpcdance. Crossover Frequencies. Power Requirement ". Fuse Requirements . Dimensions .. .. _.......... (4 ohms) 50 Watl~ per channd RMS, kss than 0.3% THO (2 ohms) 75 wa[l~ per channel RMS. Ic~s '_han 05% THO (4 ohms) hridged ! 50 walL, per channel RMS, less than 0.5% THO _.