JENSEN BT250 Bluetooth Car Kit User ’s Manual Installation and User Manual
Preface This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. Version 2.0, March 2009 Trademarks Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.
Bluetooth Car Kit User Manual Preface ....................................................................................................................i Installation ..............................................................................................................1 Identifying components......................................................................................1 Installing the junction box..................................................................................
Bluetooth Wireless Car Kit Installation This section demonstrates how to set up and install the Bluetooth Wireless Car Kit into a vehicle. Identifying components Unpack the Car Kit package and ensure the following items are included. Wired Remote Part # 31092000 Microphone Part # 31092440 Junction box Part # 31092100 Speaker Power Cable Fuse & Hardware Set Part # 31092430 Part # 31092160 Part # 31092010 Some items may vary slightly from the picture shown.
Bluetooth Car Kit User Manual Installing the junction box This Car Kit is designed to work with a 12/24-volt vehicle power supply. Refer to the following to install the junction box in a vehicle. 1. Locate a suitable place inside the car to mount the junction box. Select a dry place that avoids excessive heat and mechanical vibration. Ideally, the junction box should be hidden from view, but still easily accessible.
Connecting the power supply The following illustration demonstrates how to connect the Car Kit’s power cable to the vehicle’s electrical system. Power Cable Important! The Blue cable must be connected to the 12/24-volt switched ignition to enable the Car Kit to go into standby mode. Do not connect the Blue cable to the +12/24-volt constant connection. Doing so may discharge the battery of the vehicle and prevent the Car Kit from being reset.
Bluetooth Car Kit User Manual Connecting Components The following illustration shows where to connect the devices. Do not connect the components until you have followed the next steps and have finalized your installation. ÒCONNECT THE POWER HARNESS LAST. Junction box Speaker Microphone 4 Remote Control Remote Control The control module should be located within reach and view of the driver.
Installing the Components Before installing the components, take note of the following: • Make sure that the cables can reach from the each component to the Junction Box. If the cable is too short, relocate the component. Do not lengthen the cable. • The supplied microphone is uni-directional. For best results, place the microphone in front of the person talking. It has a reception angle of 60 degrees, and is most effective within a 24 inch radius.
Bluetooth Car Kit User Manual Getting Started Introduction The Bluetooth Wireless Car Kit is designed to help make your driving experience more convenient, safe, and provide you with years of trouble free use. Product overview and features The Car Kit is designed to make driving your car and talking on the phone safe and easy. It consists of a receiver, a remote control, a uni-directional microphone, and a speaker.
Using the remote control The Car Kit is operated using the remote control: Answer Calls / Volume Down Volume Up Disconnect LED Indicator / Voice Dialing / Reject Calls Control Module Functions Volume up / down Answer / redial Press during operation to increase or lower the volume. Press to answer a call. Call waiting: Press to answer a second call. Press again to return to the first call. Press & hold for 3 seconds to redial the last number you called.
Bluetooth Car Kit User Manual Disconnect / voice recognition LED indicator Press to disconnect a call. Press and hold for two seconds to activate the Voice Recognition function. After the tone, repeat your pre-recorded voice tag: the number automatically dials. Press to reject an incoming call. *Phone MUST Support voice recognition. Lights after pairing and during calls. Indicates power is on. Pairing phones To use a phone with the BT250 you must first pair the phone and the BT250.
Turning off the BT250 & the Blue LED light When the BT250 is not connected to any phone the Blue LED light will continue to flash. You can turn the unit off by pressing & holding the End button for 3 seconds (Please note that the button backlight will still be on all the time) until you see the Blue LED light shut off. To reactivate the BT250 simply restart the engine to reset the car kit’s power.
Bluetooth Car Kit User Manual Resetting the Car Kit The car kit may only connect to one phone at a time. However, it may be paired with up to 4 phones. Resetting the car kit deletes all pairings. To do so: Press and hold the Answer/redial and Volume down at the same time. You will hear a tone (pairing mode), continue holding the buttons until you hear the second tone. Transferring calls To transfer a call from the BT250 to the phone, do the following.
the way you say the voice tag, but also record a familiar background noise. Since phones are in continual contact with the Car Kit, it is possible to use the included Car Kit’s microphone to record the voice tag. Locate the feature on your mobile phone, and when prompted for the voice tag, speak clearly from a comfortable in the driver’s seat. This system accesses the voice recognition system in your phone.
Bluetooth Car Kit User Manual Troubleshooting My mobile phone can’t make a connection. • Make sure the bluetooth function on your phone is enabled. • Make sure the car ignition is on. If on and no power check the fuses and wiring. • Reset the Car Kit and try again. • Turn your phone off and on again, and try the proceedure for connection once more. • If your phone is very new check the support website for an upgraded software version.
Warranty Information 12 MONTH LIMITED WARRANTY Applies to Jensen Series Mobile Electronics. AUDIOVOX Electronics Corporation (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, (other defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor.
Bluetooth Car Kit User Manual © 2009 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y.