i JENSEN BT360 Bluetooth Car Kit User ’s Manual Installation and User Manual
Bluetooth Car Kit User Manual Preface This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. Version 2.
Perface....................................................................................................................... i Identifying components......................................................................................1 Installing the junction box..................................................................................2 Installing the Components..................................................................................5 Installing the microphone & speaker..................
Bluetooth Car Kit User Manual Installation This section demonstrates how to set up and install the Bluetooth Wireless Car Kit into a vehicle. Identifying components Unpack the Car Kit package and ensure the following items are included. Remote Control Microphone Junction box Part # 31102000 Part # 31092440 Part # 31102100 Power Cable Fuse & Hardware Set Part # 31092160 Part # 31092010 Speaker Part # 31092430 Some items may vary slightly from the picture shown.
Installing the junction box This Car Kit is designed to work with a 12 - 24-volt vehicle power supply. Refer to the following to install the junction box in a vehicle. 1. Locate a suitable place inside the car to mount the junction box. Select a dry place that avoids excessive heat and mechanical vibration. Ideally, the junction box should be hidden from view, but still easily accessible. Note: Make sure that the cables are long enough to support the location of the junction box.
Bluetooth Car Kit User Manual Connecting the power supply The following illustration demonstrates how to connect the Car Kit’s power cables to the vehicle’s electrical system. Yellow cable To car radio mute (NPN 300mA) Red cable To battery + 12/24V Power cables Blue cable To ignition Black cable GND Important! The Blue cable must be connected to the +12/24-volt switched ignition to enable the Car Kit to go into standby mode. Do not connect the Blue cable to the +12/24-volt constant connection.
Connecting Components The following illustration shows where to connect the devices. Do not connect the components until you have followed the next steps and have finalized your installation. ÒCONNECT THE POWER HARNESS LAST. Junction box Speaker Microphone Control Module Control Module The control module should be located within reach and view of the driver. Speaker For best reception, the speaker should be mounted at least 80 cm (30 inches) from the Car Kit’s microphone.
Bluetooth Car Kit User Manual Installing the Components Before installing the components, take note of the following: • Make sure that the cables can reach from the each component to the Junction Box. If the cable is too short, relocate the component. Do not lengthen the cable. • The supplied microphone is uni-directional. For best results, place the microphone in front of the person talking. It has a reception angle of 60 degrees, and is most effective within a 24 inch radius.
Installing the remote control Find a suitable place for remote control that will provide the best visibility. Remove dust and grease from the surface and firmly press BT360 control in place with the sticker pads provided.
Bluetooth Car Kit User Manual Getting Started Introduction The Bluetooth Wireless Car Kit is designed to help make your driving experience more convenient, safe, and provide you with years of trouble free use. Product overview and features This Car Kit is designed to make driving your car and talking on the phone safer and easier. It consists of an OLED display / remote control, a uni-directional microphone, and a speaker.
If you have a question about your phones features refer to the owner’s manual of your phone. This Bluetooth Kit uses the latest Version of Bluetooth Software. Version 2.1. In the case of an upgraded software version for new phones in the future you can obtain the software upgrade instructions and software at WWW.JENSEN.COM. The BT360 is designed to be on when ever your car is turned on.
Bluetooth Car Kit User Manual Using the remote control The BT360 is operated using a wired remote control: Control Module Functions Volume Press during operation to increase or lower the volume. Up/Down Answer/ Dial Last Call Press to answer a call. For call waiting, press to answer a second call during a call. Press again to return to the first call. To redial the last number called press and hold.
End/ Press to reject / disconnect a call. Press and hold for two Voice Dial seconds to activate the Voice Recognition function. After the tone, say the name and the phone will automatically dial. Note: The voice dial function works only when the mobile phone supports this function. OLED Display Display’s caller ID, FM Transmitter Frequency, Pairing Information, Paired Phone Name, Status.
Bluetooth Car Kit User Manual 2. Press and hold the Answer/redial and End/Voice dial buttons at the same time for 3 seconds until you hear a tone and the Display shows “pairing”. 3. Be sure Bluetooth is enabled on your phone. Follow the documentation provided with your phone to search for new devices. 4. Select the BT360 from the list of Bluetooth devices on your phone. 5. Enter the passcode: 1234. when prompet on your phone. 6.
Operation with multiple paired phones When the ignition is turned on the BT360 begins to search for paired phones. Priority is given to the most recently connected phone. Example: Phone A is connected first, phone B is connected second and phone C is connected third. If all three phones are in the car when the ignition is turned on phone C will establish a connection with the BT360. Note: If phone C is turned off or if the person using it leaves the car and goes out of range the connection will be broken.
Bluetooth Car Kit User Manual The car kit only connects to one phone at a time. However, it can be paired with up to 4 phones. Using Master Reset function will delete all pairings. To reset press and hold the Volume up and down keys at the same time. Continue holding the buttons until you hear a tone. After master reset, all the paired setting will be erased, you can now pair your phone.
Note 1: The display will not show Incoming Call 2 during the call, but you will hear a waiting tone so you remember there is another call waiting. Note 2: To transfer a privacy call from your phone to the BT360 follow the instructions provided with your phone. Setting the FM Transmitter Mode for A2DP a. Press the Play/Pause key for 3 seconds to enter the FM mode. The control will display “FM MODE” Eg: M1 88.1 FM MODE b.
Bluetooth Car Kit User Manual Eg: (3 secs) Æ or to adjust Æ confirm d. The BT360 can memorize 3 FM channels. When playing music, first enter the FM mode, then press the Play/Pause key one time to view the 3 set stations you have selected, M1, M2, M3. NOTE: The music will be muted automatically when a calls comes in. Calls are heard only through the BT360 Speaker, not the car speakers. Last Number Re-Dial Press and hold the Send key “ Eg: ” to activate the last dial feature.
Voice Dialing Press and hold the End Key “ ” to activate the voice dial Eg: Nokia N95 Voice Dial Note: Voice dialing MUST be supported by your phone to use this feature. Multimedia Function Using the Multimedia buttons to Play, Pause, Stop and jump to Next or Previous song. Note: For some mobile phones, users will need to turn on the MP3 before BT360 can play the Media function.
Bluetooth Car Kit User Manual to re-record the voice tag while you are in the car. This will set not only the way you say the voice tag, but also record a familiar background noise. Since phones are in continual contact with the Car Kit, it is possible to use the included Car Kit’s microphone to record the voice tag. Locate the feature on your mobile phone, and when prompted for the voice tag, speak clearly from a comfortable position in the driver’s seat.
BT Update USB MODE After upgrading, please turn the unit off and on again by turning your cars ignition on and off.
Bluetooth Car Kit User Manual Troubleshooting My mobile phone can’t make a connection. • Make sure the bluetooth function on your phone is enabled. • Make sure the car ignition is on. If on and no power check the fuses and wiring. • Reset the Car Kit and try again. • Turn your phone off and on again, and try the proceedure for connection once more. • If your phone is very new check the support website for an upgraded software version.
Warranty Information 12 MONTH LIMITED WARRANTY Applies to Jensen Series Mobile Electronics.
Bluetooth Car Kit User Manual © 2009 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y.