VM9314 Operating Instructions PIC CLOSE SRC WIDE TILT VM9314 EJECT MUTE DISP PTT ® A/V INPUT 160 watts peak 40W x 4
VM9314 ii
VM9314 CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9314 Mobile Multimedia Receiver for maximum enjoyment. Features ................................................................................................................................ 1 Optional Equipment .............................................
VM9314 iv
VM9314 FEATURES Congratulations on your purchase of the Jensen VM9314 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9314 installed by a reputable installation shop.
VM9314 Chassis • 1.
VM9314 OPTIONAL EQUIPMENT • • • • • NAV102 The VM9314 is "navigation ready." Before accessing any navigation features, you must purchase and install the navigation module (NAV102). All installation and operating instructions will be included with the navigation module. Once the navigation module is connected and operating properly, the NAV source mode will become active. While the navigation module is not installed, the NAV option appears gray, indicating the function is not available.
VM9314 WARNINGS WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law. WARNING! Never disassemble or adjust the unit. WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water. WARNING! Never use irregular discs.
VM9314 ANTI-THEFT FEATURE The VM9314 is equipped with an anti-theft feature requiring the user to enter a password upon initial power on. * 1 2 3 4 5 6 7 8 9 0 C Entering the Default Password The default user password is 012345 (6 digits). Enter the password using the on-screen keypad and then press the arrow (enter) button. You can also use the remote control keypad to enter the password. Press the >/|| button (30) on the remote control to confirm.
VM9314 Changing the Password To change the SECURITY password using the touch screen, perform the following steps: 1. Touch the button to view the “SETUP” menu. 2. Touch SECURITY to view the “SECURITY” sub-menu. TIME P.VOL SCREEN THEME SWC SECURITY VERSION SECURITY Please input password AUDIO VIDEO Password Factory Settings **** 1 2 3 4 5 6 7 8 Restore Exit BT 9 DVD 0 Clear RADIO 3. Enter the current password (default is 012345) and touch the arrow (enter) key. 4.
VM9314 CONTROLS AND INDICATORS 1. Rotary Encoder Rotate to adjust the volume. While in the audio menu, press and release to enter and/or confirm audio settings. Press to activate the MUTE function and silence the receiver. Press again to resume sound. 2. SRC Press to turn the unit on. Press and hold to turn the unit off. When on, press to view the SOURCE menu. 3. IR Remote Control Receiver 4. USB Interface Connector Connect a USB device for playback of music/video files. 5. TFT Display 6. 3.
VM9314 13. WIDE/ |<< Press to adjust the display aspect of the picture to one of two settings: Full, Normal or STANDBY. With the monitor closed, press to seek backward. When the NAV102 is connected to the VM9314, press and hold to display the navigation user interface. The TFT screen must be open for this function to operate. 14. PIC/BAND Press and hold to view the setup menu. Touch “Screen” to adjust dimmer and backlight picture settings (see “SCREEN Sub-menu Features” on page 22).
VM9314 REMOTE CONTROL 15 14 13 PIC CLOSE 12 WIDE TILT 5 7 VM9314 2 EJECT MUTE 1 DISP A/V INPUT PTT 10 3 16 11 9 9 6 4 8
VM9314 See remote control tables in various sections for button functions.
VM9314 USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (15) on the front panel or press the ( ) button (25) on the remote control to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (15) on the front panel or press the ( ) button (25) on the remote control to load the display panel back into the compartment.
VM9314 Aspect Ratio Press the DISP button (10) on the remote control or WIDE button (13) on the monitor to adjust the aspect ratio as follows: FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display. STANDBY Screen becomes black. Touch screen to resume.
VM9314 Table 1: Monitor Protective Measures Obstruction OPEN Button Pressed Self Protection Power Reconnected Monitor loading in horizontally Unit stops at obstruction point Monitor fully extended horizontally Monitor is automatically loaded into unit Monitor loading out vertically Unit stops at obstruction point Monitor swivels back to the unit Monitor swivels back to the unit Monitor loading in vertically Unit stops at obstruction point Monitor swivels back to the unit Monitor swivels back
VM9314 OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (2) on the unit (or the button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (11). You can also turn on the unit by pressing the OPEN button (15) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment.
VM9314 Mute/Line Mute Press the rotary encoder button (1) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit. Press the rotary encoder button again to restore the volume. “MUTE” is displayed on the LCD. Adjusting the volume or using any of the audio setup features cancels the mute function.
VM9314 NOTE: You can press and hold to drag the “Source Menu” icons and rearrange them based on your preference External Devices External peripheral devices, including a game console, camcorder, navigation unit, iPod, Zune, etc. can be connected to this unit via RCA output using the A/V Media Adapter Cable (included). EJECT A/V INPUT 1 Right Audio 2 Left Audio Ground Video 3 4 3.
VM9314 Programmable Turn-On Volume This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off. To use this feature, the TFT monitor must be displayed. To program a specific turn-on volume level, turn the rotary encoder (1) to adjust the volume to the desired turn-on volume. Push and hold the rotary encoder while the yellow speaker icon and level indication is displayed on the screen.
VM9314 • Use the touch screen to adjust the settings for an audio feature. Table 3: Audio Adjustments Audio Function EQ (NOTE: The “User” setting is automatically selected when individual BASS, MID and TREB settings are modified.) BASS MID TREB (treble) SUB.W FAD BAL Adjustable Range Dance Hip hop Rave User Acoustic Rock Latin Urban -12 to +12 -12 to +12 -12 to +12 -7 to +7 Grid Grid The Audio menu will automatically exit after a few seconds of inactivity.
VM9314 iPod VOICE CONTROL You can navigate your iPod/iPhone music library and change the source/mode using the latest in voice recognition technology, allowing you to enjoy a more handsfree experience so you can focus on driving. The VM9314 is provided with a high quality active microphone for voice control. This microphone should be mounted as close to the driver as possible, preferably on the visor directly above the driver, for best voice recognition.
VM9314 Basic Voice Operation 1. To activate the voice control function, touch the PTT button on screen or on the remote control (7). The PTT button is located on the left side of most screens, but is not present on all screens. 2. The system displays the voice icon along with the text “Please say your command” at the top of the screen. 3. The system “listens” for a command for 5 seconds. 4. Speak a command into the microphone within 5 seconds. • If speech is not detected, the system displays “No speech.
VM9314 SETUP MENU To access system settings, touch the button on the screen to enter the setup menu. The “TIME” sub-menu appears highlighted in yellow. TIME P.VOL AUDIO SCREEN THEME SWC SECURITY VERSION TIME Jan 01 2009 VIDEO 7:46 PM BT DVD Clock Mode 12-hour 24-hour RADIO Accessing Menu Items Touch to select a sub-menu (Screen, Theme, SWC, etc.). The features available for adjustment under the highlighted sub-menu option will appear in the center of the screen. Adjusting a Feature 1.
VM9314 TIME Sub-menu Features Setting Options Function Clock Mode 12-hour Clock displays 12 hour time using AM and PM. 24-hour Clock displays 24 hour time up to 23:59. Month Jan-Dec Touch to view the direct entry keypad. Enter numeric equivalent of current month (1-12) and touch the enter key. Day 01-31 Touch to view the direct entry keypad. Enter current day of the month (01-31) and touch the enter key. Year 20_ _ Touch to view the direct entry keypad.
VM9314 Setting Options Function OSD English English is the only available On Screen Display option. DEMO Run Demo scrolls through the various source screens, simulating activity on the display. “Demo” is displayed in the top left corner of the screen, to indicate the unit is in Demo Mode. To stop Demo Mode, press the upper-left quadrant of the TFT (Source select).
VM9314 SECURITY Sub-menu Features. Setting Options Function Password ****** Enter the current password (default is 012345) and touch the arrow (enter) key to access SECURITY features. To change the password, touch the “Password” field to open the on-screen keypad. Enter a new 6-digit password and press the arrow (enter) button. Factory Settings Restore Select “Restore” to restore the factory default settings.
VM9314 AUDIO Sub-menu Features Setting Options Loudness On DRC On Function Turn bass boost on/off Off Off Subwoofer On Subwoofer Filter 80Hz Employ the Dynamic Range Control for better playback for low volumes. Turn the subwoofer on/off. Off 120Hz Selecting a crossover frequency sets a cut-off frequency of the subwoofer's LPF (low-pass filter).
VM9314 BT (Bluetooth) Sub-menu Features Setting Bluetooth Options On Function Enable Bluetooth function. Off Disable Bluetooth function. Auto Answer On The unit automatically answers all incoming calls. Auto Connect On Automatically connect when your paired phone is in range. Off Connect the last active mobile phone by touching the icon when disconnected. Pairing Code **** The default code is “1234”.
VM9314 NOTE: Record the password and keep it in a safe place for future reference. The rating for each disc is marked on the disc, disc packing, or documentation. If the rating is not available on the disc, the parental lock feature is unavailable. Some discs restrict only portions of the disc and the appropriate content will play. For details, please refer to the disc description. RADIO Sub-menu Features Setting Tuner Area Options Function U.S.A.
VM9314 TUNER OPERATION To access the radio (HD) screen, press the SRC button (2) on the front panel or remote control (8) or touch the top left corner of the screen to access the Source menu, and then touch the “RADIO” icon. With the screen closed, press the SRC button (8) on the remote control until “RADIO” appears on the LCD. The on-screen indicators and touch key areas for radio mode are outlined below. 8 17 HD 1 2 22 9 4 10 27 5 Auto P1 FM 87.5 MHz ON P3 FM 98.1 MHz 19 01:02 PM FM 87.
VM9314 17. (a) Current source (b) Touch to view the SOURCE MENU and select a new source 18. AS: Scan and automatically store strongest received stations 19. : View the SETUP menu 20. TAG: Tag the current song for possible iTunes download. If an iPod is connected, the tag goes directly to the iPod/iPhone. If no iPod is connected, the unit stores the tag (up to 64) for transfer to the iPod later. 21. PTT: Activate the Push To Talk voice recognition feature. See “iPod Voice Control” on page 19. 22.
VM9314 Direct Tuning To enter a radio station directly, touch the button or press the GOTO button (21) on the remote control to display the direct entry menu. FM . MHz 1 2 3 4 5 6 7 8 9 Exit 0 C Enter the desired radio station using the on-screen number pad. Press the arrow (enter) button to tune to the selected station. To exit the screen without changing the station, touch Exit. To clear your entry and start over, touch Clear.
VM9314 Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (6) to select the corresponding stored station. P1 FM 87.5 MHz P2 FM 90.1 MHz P3 FM 98.1 MHz P4 FM 106.1MHz P5 FM 107.9MHz P6 FM 102.9MHz Auto Store (AS) To select 18 strong stations and store them in the current band: 1. Select a band (if needed). 2. Touch the AS button (18) on page 1/2 of the on-screen controls to activate the Auto Store function. The new stations replace stations already stored in that band.
VM9314 DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “WARNING!!! It is illegal to view video while driving or operating a motor vehicle, Set parking brake to view video.” Rear video screens, if applicable, will operate normally.
VM9314 Resetting the Loading Mechanism If the disc loads abnormally or an abnormal core mechanism operation occurs, press and hold the button (8) on the unit or remote control (35) to reset the loading mechanism. Normal operation resumes. Accessing DVD Mode To switch to DVD mode when a disc is already inserted, press the SRC button (2) on the front panel or remote control (8) to access the SOURCE MENU. Touch the “DISC” icon.
VM9314 Table 5: DVD/VCD Remote Control Functions Button Name ANGLE Function DVD VCD Play alternate angles if DVD contains scenes shot simultaneously from different angles Controlling Playback To access the on-screen controls, touch the bottom 1/3 of the screen while a DVD is playing.
VM9314 Fast Forward Playback Press the button (14) on the remote control or the button on the screen to fast forward. Keep pressing and releasing the button to increase the rate from “x2” to “x4”, “x8”, and “x20”. Press /|| (18) on the remote control or touch the on-screen play button ( ) to resume normal play.
VM9314 Press the | button (17) on the remote control or the | move to the previous chapter. button on screen to Goto Search (Remote Control Required) During DVD or VCD playback, perform the following steps to use the GOTO feature to access a specific location on a disc: 1. Press the GOTO button (21) on remote control to access the “Search” screen. 2. Press the or buttons (14, 22) on the remote control to select a category (highlighted in yellow).
VM9314 Direct Chapter / Track Selection Remote Control Direct Entry During DVD, VCD and CD playback, you can use the numeric keypad on the remote control (29) to access a track directly. Touch Screen Direct Entry To select a chapter/track directly, touch the display the direct entry menu. button on screen control to Chapter: _ 1 2 3 4 5 6 7 8 9 Exit Enter 0 Clear Enter the desired chapter/track using the on-screen number pad. Press the Enter button to tune to the selected station.
VM9314 Zooming Press the ZOOM button (23) on the remote control to enlarge and pan through the video image using the following options: “Q1”, “Q2”, “Q3” and “OFF”. Multi-Language Discs (DVD Only) Changing Audio Language If you are watching a disc recorded in multiple languages, press the AUDIO button (5) on the remote control to choose a language.
VM9314 • Chapter 2/16 – Indicates that the second of 16 titles on the DVD is currently playing. VCD Playback Information • VCD2.0 – Format of current disc. • Time 00:01:30/00:36:10 – Indicates the playback time of the current track. • PBC On/Off – Indicates whether Play Back Control is On or Off.
VM9314 Table 7: Disc Symbols Symbol Meaning Indicates the region code where the disc can be played.
VM9314 DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9314 will play music or other audio files from the following disc media: • CD-DA • CD-R/RW • DVD • DVD+R/RW • DVD-R/RW NOTE: CD-R and CD-RW will not play unless the recording session is finalized.
VM9314 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Elapsed playing time Current time Track titles Disc title /||: Play/pause : Stop disc playback. Press /|| to resume normal playback. | : Previous track |: Next track : Fast reverse x2, x4, x8, x20. Press /|| to resume normal playback. : Fast forward x2, x4, x8, x20. Press /|| to resume normal playback. 12.
VM9314 Remote Control Functions Table 8: CD/DVD Audio Remote Control Functions Eject disc || / BAND Select AM/FM band | Previous track | Next track Fast reverse x2, x4, x8, x20 Fast forward x2, x4, x8, x20 /|| Play/pause Stop playback 1-9, 0 Direct entry EQ Access equalizer menu GOTO Access direct entry keypad PTT Push to talk RPT CDDA: (x1) Repeat Single, (x2) Repeat Folder, (x3) Repeat Off DVD: (x1) Repeat Chapter, (x2) Repeat Title, (x3) Repeat Off CD-R/RW: (x1) Repeat Single, (x2) Repe
VM9314 Direct Track Entry To select a track directly, touch the direct entry menu. button on screen control to display the Track:__/8 1 2 3 4 5 6 7 8 9 Exit 0 Clear Enter the desired track using the on-screen number pad. Press the enter button (arrow) to play the selected track. To exit the screen without selecting a track, touch Exit. To clear your entry and start over, touch Clear.
VM9314 MP3 OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. Media and File Requirements This player allows you to play back MP3 and WMA files recorded onto CD-R/ RWs, DVD+R/RWs, and DVD-R/RWs. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent illegal disc operation.
VM9314 For example, a medium with the following folder/file hierarchy is subject to Folder Search, File Search or Folder Select, as shown below. The VM9314 player will only recognize three folder levels and does not display folders containing only other folders. In the example above, the unit will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain any tracks directly. Folder 5 is not recognized at all since it is at the fourth level.
VM9314 Accessing an SD Card 1. Locate the SD connector (9) on the front of the radio. 2. Insert the SD card into the SD connector. 3. Press the SRC button (2) on the front panel or remote control (8) or touch the top left corner of the screen to access the Source menu, and then touch the “SD” icon. EJECT A/V INPUT Before removing the SD card, change the radio to another source. To remove, pull straight out. NOTE: Maximum SD card size supported by this unit is 16GB.
VM9314 On-Screen Controls and Indicators The on-screen indicators and touch key areas for MP3 playback are outlined below. 22 17 1 19 14 2 16 01:02 PM Folder: MP3 1/141 L O U D 1 World in My Eyes 2 Sweetest Perfection ON 3 Personal Jesus 4 Halo 5 Waiting for the Night 6 Enjoy the Silence P T T 3 00:01:51 21 15 EQ EQ 10 25 6 8 27 11 28 - 1/2 18 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
VM9314 21. 22. 23. 24. Repeat and Random playback indicators LOUD: Turn loudness features ON/OFF DIR -: View the previous folder DIR +: View the next folder 25. : List audio files 26. : List photo files (see “Viewing JPEG Photos” on page 50) 27. : List video files (see 28.
VM9314 VIEWING JPEG PHOTOS JPEG images stored as individual images or stored in folders can be accessed using the DISC/SD/USB interface. When a disc/card is loaded and read by the unit, the root menu will display the music contents of the disc when music files are present. To view photos, press the 1/2 button to view a second page of controls and then press the button. Controlling Playback Touch the arrows and scroll bar to the right of the image names to navigate the list.
VM9314 MPEG MOVIE PLAYBACK Version 1 and 2 MPEG movies can be accessed using the DISC/SD/USB interface. When a disc/card is loaded and read by the unit, the root menu will display the music contents of the disc when music files are present. To view MPEG movies, press the 1/2 button to view a second page of controls and then press the button. Controlling Playback Touch the arrows and scroll bar to the right of the movie names to navigate the list. Touch the movie name to play that movie.
VM9314 17. DISP: Display file information (file name and track number) Returning to the Music Interface To return to the music interface, touch the icon to list audio files. Touch to select an audio file and begin playback. Touch the 2/2 button to view MP3 playback controls.
VM9314 XM RADIO OPERATION ® Listeners can subscribe to XM® Radio on the Web by visiting www.xmradio.com, or by calling (800) 967-2346. Customers should have their Radio ID ready (see “Displaying the Identification (ID) Code”). Customers can receive a limited number of free-to-air channels without activation. Accessing XM® Radio Mode Press the SRC button (2) on the front panel or remote control (8) to switch to the XM source.
VM9314 16. BAND: Change between XM1, XM2 and XM3 bands 17. : View the SETUP menu 18. Touch this area to view the SOURCE MENU and select a new playback source 19. MEM: View screen used to enter current channel into preset memory 20. PTT: Activate the Push To Talk voice recognition feature. See “iPod Voice Control” on page 19. 21.
VM9314 Storing a Station 1. Select a band (if needed), then select a station. 2. Touch the on-screen MEM button to open the preset screen. MEM : P1 P4 P2 P3 P5 P6 Exit 3. Touch the preset number in which you would like to store the current station (or press Exit to cancel and close the menu). The preset number and station appears highlighted. Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button to select the corresponding stored station.
VM9314 Channel/Category Guide Mode There are two search modes to help navigate through channels and or categories. To access the Channel/Category Guide mode, touch the CG button. Channel Guide is the default search mode. To access Category Guide, press the SUBTITLE button (9) on the remote control or touch CAT on the touch screen. To return to Channel Guide, touch CH on the screen or press the TITLE button (2) on the remote control.
VM9314 Category Guide Mode When Category Mode is selected, folder icons appear on the screen next to category choices. • While in Search Mode, to switch between Channel and Category search modes, touch the CH or CAT buttons on the screen. • Use the scroll bar and arrows on the touch screen to view the next/ previous page of categories. Each page contains six categories to select from. • To select a category, touch the corresponding category name or folder icon.
VM9314 iPod OPERATION NOTE: Be sure your iPod has the latest Apple firmware installed to avoid connectivity issues. Accessing iPod Mode This unit is Made for iPod and works with iPhone. You can control your iPod via touch screen to access Playlist, Artist, Album, Songs, etc.
VM9314 2. 3. 4. 5. 6. File number and total number of files on the iPod Current time File titles ID3 information (Artist/Album) ENTER: Touch to “Enter” 7. : Activate/deactivate Random mode 8. |: Next track 9. | : Previous track 10. : iPod Menu 11. ||: Play/pause 12. 13. : (x1) Repeat Single, (x2) Repeat All : View the song title screen 14. : View the SETUP menu. 15. : Quick access to Equalizer level settings. 16. (a) Current source (b) Touch to view the SOURCE MENU and select a new source 17.
VM9314 Controlling your iPod Touch the button or press the following remote control buttons to access the main iPod menu. Menu Music Photos Videos Remote Control AUDIO SUBTITLE ANGLE Use the touchscreen or the directional keys on the remote control to navigate the iPod menus. File Playback To access files, touch the button on screen until you return to the main iPod menu and then select “MUSIC,” “VIDEO” or “PHOTO” or press the remote control button indicated in the table above.
VM9314 • To return to the Video or Photo menu while viewing video or photo, touch the center of the screen. NOTE: The jLink USB cable must be used for video playback. NOTE: Only the iPod Touch (1, 2, 3 Gen) and iPhones allow photo viewing through the VM9314. Fast Forward/Fast Reverse Press and hold the | or | buttons on screen or on the remote control (17, 19) for 1 second and continue to hold for fast forward or fast reverse. Release to resume normal play.
VM9314 BLUETOOTH OPERATION NOTE: Bluetooth operation requires an optional BTM15 accessory. The BTM15 module has a secondary microphone for voice recognition. When installing the BTM15, the original single microphone that came with the VM9314 can be disconnected and the BTM15 secondary microphone can be used. This connectivity eliminates the original microphone and allows the BTM15 to perform voice recognition and Bluetooth functions for a cleaner looking installation.
VM9314 • • • • • • • • • Try to perform pairing within a few minutes of the phone being turned on. Once the unit has been paired with the phone, the unit’s model number, “VM9314”, will be displayed on the mobile phone. To achieve the best performance, always keep the mobile phone within 3 meters of the head unit. Always keep a clear path between the mobile phone and the head unit. Never place a metal object or any other obstacle between the mobile phone and the head unit.
VM9314 Bluetooth User Interface The on-screen indicators and touch key areas for Bluetooth operation are outlined below. 5 1 15 17 2 14 01:02 PM 13 EQ 1 Blackberry 8300 L O U D 2 iPhone EQ 8 20 12 21 ON P T T 6 22 16 History Paired List 10 3 4 18 11 7 9 16 PHONE INTERFACE (Not Connected) 1. 2. 3. 4. 5. 19 MUSIC INTERFACE Name of connected device Current time List of previously paired devices Current operation status LOUD: Turn loudness features ON/OFF 6.
VM9314 17. : Access the direct entry screen 18. Touch the scroll bar and arrows to view the previous/ next page of choices (only visible when needed) 19. | : Previous file 20. ||: Play/pause 21. |: Next file 22.
VM9314 Pairing the Bluetooth System with Your Mobile Phone and Head Unit 1. Press the button (7) to initiate the pairing process. Keep the mobile phone within 2 meters of the head unit when pairing. (To terminate the pairing process, press the button again.) 2. Select the Bluetooth setup option on the mobile phone to be paired (please refer to the phone’s instruction manual to learn how to enter Bluetooth setup, turn Bluetooth on/off, and perform pairing).
VM9314 Reconnecting Once the Bluetooth device has been paired, you can touch the connect button (9) to reconnect. NOTE: You can only connect to a phone using the buttons on the onscreen Phone interface. Each time the button is pressed, the head unit will automatically reconnect with the mobile phone once (only if the mobile phone was previously paired with the head unit).
VM9314 1. Touch the button to open the direct dial screen. 5551237845 1 2 3 Exit 4 5 6 C 7 8 9 * 0 # 2. Use the 0-9, *, and # buttons to input the phone number. Touch the C button to clear the last digit. 3. After entering the phone number, press the button to dial the call. The direct dial screen will close once your call is connected. To end the conversation, press the button.
VM9314 NOTE: Not all phones allow access to missed, received or dialed calls and some will not allow uploading of your phone’s address book. Missed Calls The Missed Calls list retrieves the list of Missed numbers from your phone. The last missed number is the first number on the list. Touch the Missed Calls menu option to view the list. To make a call from the Missed Calls list, touch the number (the selected number appears at the top of the screen) and then touch the button.
VM9314 Bluetooth Setup Auto Answer You can choose to have the VM9314 automatically answer incoming calls to your paired Bluetooth phone. To turn “Auto Answer” on: 1. Touch the button to view the SETUP menu. 2. Select the “BT” sub-menu. 3. Touch the area to the right of “Auto Answer” to select “On”. Auto Connect The auto Connect option will allow the VM9314 to automatically connect to your previously paired Bluetooth when it is in range.
VM9314 REAR CAMERA FUNCTION This unit is “camera ready.” Before accessing any camera features, you must install a rear video camera. When the camera is not installed and the function is accessed by gear selector being placed in reverse or by the unit’s menu, the message “NO VIDEO SIGNAL” will appear, indicating the function is not available. When the camera is installed, the rear view image of what’s behind the vehicle will appear when the vehicle’s is placed in reverse gear.
VM9314 TROUBLESHOOTING Table 13: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right corner of the front panel Remote control does not function Battery depleted Replace battery with new one Battery installed incorrectly Remove battery and install correctly No/low audio output Improper
VM9314 Table 13: Troubleshooting Problem Cause Corrective Action Prolonged image or improper height/width ratio display Improper aspect ratio setup Use correct aspect ratio setting Monitor stops at incorrect position Moving path is blocked Press OPEN key to restart monitor movement Auto antenna is not fully extended Connect the auto antenna control cable properly Auto antenna not properly connected Connect the auto antenna control cable properly LOCAL function is activated Turn LOCAL function
VM9314 Table 13: Troubleshooting Problem Incorrect playback message displayed Cause Corrective Action Message is longer than LCD can display Error Messages Table 14: Error Messages Message Displayed Cause Corrective Action Loading Disc is being read No Disc Disc is dirty Clean disc with soft cloth Disc is upside down Insert disc with label side up Disc not present in loading compartment Insert disc Bad Disc Disc is dirty Clean disc with soft cloth Disc is upside down Insert disc with lab
VM9314 Care and Maintenance 1. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and non-neutral detergent (such as alcohol) may result in scratching or discoloration. 2. Do not get water or cleaning fluids on the unit. 3. If the temperature inside the player gets too hot, a protective circuit automatically stops play of the disc. If this occurs, allow the unit to cool before operating the player again. 4.
VM9314 SPECIFICATIONS DVD/CD Player Compatible Disc Media: DVD + R / RW (Single and Dual Layer) and CD-R / RW Compatible Media Formats: CD-DA, MP3, WMA, VCD, SVCD, Xvid, AVI, MPEG1 / 2 Signal to Noise Ratio: >95dBA Dynamic Range: >95dB Frequency Response: 20Hz to 20 kHz, -3dB Channel Separation: > 60dB @ 1 kHz D/A Converter: High performance 24-bit / 192 kHz sample rate, Multi-Bit Sigma-Delta Modulator Video Format: NTSC, PAL (auto-detection) Output: 1Vp-p (75-ohm) Input: 1Vp-p (75-ohm) FM Analog Tuner Tun
VM9314 Monitor Screen Size: 7" TFT Active Matrix LCD Resolution: 1,152,000 Sub Pixels (480 x 2400) General Auxiliary Input impedance: 10k Power Supply: 11 to 16VDC, negative ground Power Antenna (Blue): 500mA max, current limited protection Amplifier Remote (Blue/White): 500mA max, current limited protection Operating Temperature: -20C ~ 65C Fuse: 15-amp, mini ATM type DIN chassis dimensions: 7" X 7" X 2" (178mm x 178mm x 50mm) CEA Power Ratings Power Output: 13 Watts RMS x 4 channels into 4-Ohms @ < 1% THD
Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensen.com © 2010 Audiovox Ver.
