Use and Care Manual

E-9
Battery Precautions
 Replacement of batteries must be done by an adult.
 The supply terminals are not to be short-circuited.
 Non-rechargeable batteries are not to be recharged.
 Exhausted batteries are to be removed.
 Only batteries of the equivalent type are to be used.
 Batteries are to be inserted with the correct polarity.
 Dispose of batteries properly. Do not dispose of batteries in fire. The batteries may
explode or leak.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
The remote control supplied with this product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away from
children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
NOTE ON NON-MAGNETICALLY SHIELDED SPEAKERS
This
unit
is
not
magnetically
shielded
and
may
cause
color
distortion
on
the
screen
of
some
TVs
or
video
monitors.
To
avoid
this,
you
may
need
to
move
the
unit
further
away
from
the
TV
or
monitor
if
unnatural
color
shifts
or
image
distortion
occurs.
TURNING THE UNIT ON/OFF
1.
In
Off
(standby)
mode,
tap
the
POWER/
STANDBY
Button
on
main
unit
or
remote
control
to
turn
the
unit
ON.
The
unit
will
turn
on,
the
last
selected
input
mode
icon
will
show
on
LCD
display.
2.
To
turn
the
unit
OFF
(standby),
tap
the
Button
on
main
unit
or
remote
control
again.
The
LCD
DISPLAY
will
go
dim
and
show
the
current
time.
The
standby
mode
indicator
lights.
SETTING THE CLOCK
After
plugging
in
the
AC
power,
“
12:00
”
will
appear
and
start
blinking
on
the
LCD
display.
1.
In
Power
Off
(Standby)
mode,
press
and
hold
the
TIME
SET
Button
on
remote
control
or
main
unit,
the
12
HOUR
format
“
12H
”
will
show
in
display.
2.
Tap
the
or
Button
on
remote
control
or
main
unit
to
select
24
Hour
format
if
necessary.
Otherwise,
press
the
TIME
SET
Button
to
confirm
12
Hour
clock
format
and
enter
clock
setup
mode,
Hour
digits
will
be
flashing.
3.
Tap
the
or
Button
on
remote
control
or
main
unit
to
adjust
the
hour.
Press
and
hold
the
button
for
fast
advance
/
reverse
setting.
Note:
Make
sure
the
hour
is
set
so
that
the
PM
indicator
is
displayed
correctly
.
4.
Press
the
TIME
SET
Button
on
remote
control
to
confirm
the
hour
setting,
the
minute
digits
will
flash
to
prompt
for
input.
5.
Tap
the
or
Button
on
remote
control
or
main
unit
to
adjust
the
minute.
Press
and
hold
the
button
for
fast
advance
/
reverse
setting.
6.
Press
the
TIME
SET
Button
on
remote
control
again
to
complete
the
setting.
NOTE:
The
clock
and
radio
station
presets
will
need
to
be
reset
if
the
power
is
interrupted
or
in
the
event
of
a
power
outage.
“
12:00
”
will
appear
and
start
blinking
on
the
LCD
display
to
notify
you
that
the
power
was
interrupted
and
the
clock
will
need
to
be
reset.
Please
follow
steps
1-6
above
to
reset
the
clock.