Use and Care Manual

E-10
CHECKING THE CLOCK
The unit will show the current time in standby mode. To check the current time in Power ON mode,
press and hold the TIME SET Button on main unit or remote control for 3 seconds, the current
time will show for 5 seconds and then return to the previous screen.
ALARM OPERATION (REMOTE CONTROL ONLY)
SETTING THE ALARM CLOCK
This function allows the system to turn on automatically and wake you using a beeping alarm, the
CD or the RADIO.
1. In standby mode, press and hold the ALARM Button on remote control for 3 seconds, the
alarm icon and alarm time 12:00 will appear in display. Hour digits of alarm clock start
flashing.
2.
Press
the
/
Button
to
set
the
hour
and
then
press
the
ALARM
Button
again
to
confirm,
Minute
digits
will
be
flashing.
Note:
Make
sure
the
hour
is
set
so
that
the
PM
indicator
is
displayed
correctly
.
3.
Press
the
/
Button
to
set
the
minute
and
then
press
the
ALARM
Button
again
to
confirm,
alarm
wake
up
source
will
appear
in
display.
4.
Press
the
/
Button
to
select
wake
to
radio,
CD
or
Beep
and
then
press
the
ALARM
Button
again
to
confirm,
alarm
volume
level
will
be
flashing.
5.
Press
the
/
Button
to
preset
the
wake
up
alarm
volume
level
and
then
press
the
SELECT
Button
to
finish
alarm
setup.
NOTE:
1.) If “Wake to CD” is selected but a CD is not inserted, the alarm will default to the Beeping Alarm
automatically when the alarm wake time is reached.
2.) For ‘Wake to Radio”, the system will default to the last FM radio station listened to before
switching off.
3.) The crescendo alarm will increase to the volume level you have set.
ACTIVE/DE-ACTIVE ALARM FUNCTION
1. To active ALARM, tap the “
ALARM
”
Button
once, and the alarm icon “” will show on LCD
display.
2. Cancel the ALARM function by tapping on the “ALARM” Button again. The alarm icon “ ”
will go off.
Wake
to
Radio,
CD
or
Beeping
Alarm

When
the
alarm
time
is
reached,
the
CD,
radio
or
beeping
alarm
will
sound
for
60
minutes
then
shut
off
and
reset
itself
for
the
following
day
(without
pressing
the
snooze
button).
You
may
activate
the
snooze
function
manually
after
the
alarm
sounds
by
pressing
the
SNOOZE
Button
.
The
buzzer
stops
for
the
snooze
time
(9
minutes)
then
comes
again.
The
snooze
operation
can
be
repeated
again
within
the
remaining
minutes
from
the
set
alarm
time.
NOTE:
remaining
time
must
be
greater
than
9
minutes
from
the
alarm
off
time,
otherwise
alarm
will
stop
until
next
day
.

To
stop
the
alarm
immediately
after
it
sounds,
tap
the
Power
B
utton
on
remote
control
or
on
main
unit
once.
It
resets
itself
for
the
following
day.
 To cancel the following day alarm, tap the ALARM Button once, ALARM icon “ ” goes
off.
SNOOZE FUNCTION
Press the SNOOZE Button on remote control once to temporarily terminate the alarm mode. The
SNOOZE icon shows in display, the alarm will re-start again after 9 minutes on each press. To
cancel the SNOOZE mode, press the POWER/STANDBY Button once, the SNOOZE icon
disappears from display.