Owner's Manual

ManualsBrandsJENSEN ManualsElectronicsJENSEN 3-ZONE WALL STEREO

Table Of Contents

Auxiliary Input Function

Auxiliary Input Connector

USB Interface Connector

Clock Display

Clock Setup

Sleep Mode

Alarm Setting

Remote Sensor

Speaker Output

Reset

Press the AUX button (26) to directly access auxiliary input modes (AUX IN1 and

AUX IN2) from any other mode when a portable audio device is connected to the

unit. To connect a portable audio device, insert a standard 3.5mm (audio line

output or headphone output from your portable CD / MP3 / iPod or other media

player) into the AUX A/V IN connector (AUX IN1) (26) on the front of the unit or

the AUDIO IN (AUX IN2) on the back of the unit (see“Wiring” on page 3).

For front panel A/V input, an external audio/video (A/V) source such as a video

game player, camera, etc. can be connected to the front panel A/V input with the

provided 3.5mm A/V cable adapter (Please note that there are several different

A/V cable "standards"). Connect the device to the AUX A/V IN connector (26) on

the front panel.

In addition to front panel auxiliary input source, the unit can also be connected

to the RCA audio input through the AUX AUDIO INPUT jack on the rear of the

unit.

Press the AUX button (26) to directly access auxiliary input modes (AUX 1 IN

and AUX 2 IN) from any other mode when a portable audio device is connected

to the unit.

You can connect a USB device directly to USB interface (16) on the front of the

JWM62A for playback of compatible ﬁles. Playback begins automatically. Press

the USB button ( ) to switch to USB mode from another source. Refer to 16

“MP3/USB Operation” on page 13 for additional operating instructions.

Press the VIEW button (4) to alternate between playing time and clock time while

in Tuner, CD, DVD, USB or auxiliary input mode.

NOTE: USB will not support Apple device playback. The USB input supplies

up to 1A of charging current.

Press and hold the clock HOUR or MINUTE button (39, 36) to access clock setup

mode. The number representing the hours and minutes will ﬂash. Press the HOUR

button (39) to adjust the hour and press the MINUTE button (36) to adjust minutes.

The new time will be saved ﬁve seconds after the last adjustment is made.

The Sleep Timer will automatically turn off the JWM62A in the designated number of

minutes. To set the Sleep Time, press the SLEEP button (37) and the sleep time will

appear in the display with the number representing the minutes (SLEEP 0). Press

SLEEP button repeatedly to change the sleep time from 0 (OFF), 15, 30, 45 or 60

minutes.

To set the alarm, press and hold the ALARM SET button (38) for 2 seconds and the

clock digits will be ﬂashing. Press the HOUR button to adjust the hour once at a time

or press and hold to advance rapidly. Repeatedly press the MINUTE button to adjust

the minute one digit at a time, or press and hold to advance rapidly.

Press the ALARM SET or ENTER knob button to save the alarm time.

Once a time is set, press ALARM ON/OFF (38) to turn the alarm function on or off.

Infrared receiver is located on the upper left of front panel to receive infrared signal

emitted by the remote control.

The three speaker output buttons (19, 21, 23) (Zone A, Zone B and Zone C) control

speaker zones output from the radio. Press any of the three buttons to turn the

corresponding speaker zone on or off. SPK A (Zone A), SPK B (Zone B) or SPK C

(Zone C) will appear on the display.

The reset button should be activated for the following reasons:

• initial installation of the unit when all wiring is completed

• function buttons do not operate

• error symbol on the display

Use a ball point pen or similar object to press the RESET button (28). This may be

necessary should the unit display an error code.

JWM62A