MS30 Owner’s Manual MS30 + VOL- >ll MODE MUTE l l<< VOL+ FOLDER FOLDER >>l
MS30 CONTENTS Introduction ................................................................................................................ 1 Features ................................................................................................................................ 1 Box Contents......................................................................................................................... 1 Compliance ...................................................................................
MS30 INTRODUCTION Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen receiver for maximum enjoyment.
MS30 Safety Information • • • • • • To ensure full satisfaction with the product, please read the entire instruction manual. Keep instructions for future reference. Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Only use attachments/accessories specified by the manufacturer. Never use harsh cleaning agents.
MS30 INSTALLATION Mounting the Radio 1. 2. Choose a mounting location on the dash board or instrument panel that will allow room behind to run radio cables to the power source. Consider how you will use the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables to an accessible area. Cut a hole in the dash board using the template provided in the back of this manual. At least 3 3/4” depth is needed to mount the radio.
MS30 Auxiliary Input Connect a portable audio device to the Audio Input (AUX IN RIGHT/LEFT) on the back of the unit using RCA cables. Line Output The Line Out connectors (LINE OUT RIGHT/LEFT) on the back of the unit output a line-level analog signal. Use this output to connect to an external amplifier.
MS30 Wiring Diagram USB Connector Black Black Yellow 10AMP Type ATO Fuse Yellow Grey Grey +12 VDC SWITCHED ANTENNA AUX IN RIGHT (red) AUX IN LEFT (white) LINE OUT RIGHT (red) LINE OUT LEFT (white) NOTE: Do not connect the red wire to a constant power connection. The red wire should be connected to a vehicle connection with switched power, such as IGN or ACC.
MS30 OPERATION 1 MS30 4 2 l<< VOL+ FOLDER >ll MODE MUTE >>l l 6 + VOL- 8 FOLDER 3 7 9 5 Basic Functions Power Press the JENSEN power button (1) to turn the unit on/off. Restore Factory Settings Perform the following steps to reset the radio to factory default settings: 1. 2. 3. Press and hold the power button (1) to display the software version. Press the VOL + button (3) to display “RESET”. Press the power button to confirm factory default restore.
MS30 Audio Menu Press and hold the MODE button (8) to access the audio menu. Press the MODE button repeatedly to adjust the following settings: BASS, TREBLE, BALANCE, FADER, AS and PS. Use the VOL +/- buttons (3, 2) to choose a value for each setting. See “Radio Mode” for instructions regarding the Auto Store (AS) and Preset Scan (PS) features. Radio Mode USA/Europe (EURO) Tuning Mode Selection To change from USA to European tuning mode, perform the following steps: 1. 2. 3. 4.
MS30 USB Mode Insert/Remove USB Device You can connect a USB device directly to the USB interface at the rear of the radio for playback of compatible files. Playback begins automatically. Press the MODE button (8) to switch to USB mode from another source. Play/Pause (USB) During USB playback, press the MUTE button (9) to play or pause the selected track. Next/Previous File Press the l<< or >>l button (6, 7) to select the previous or next track.
MS30 TROUBLESHOOTING Table 1: Troubleshooting Problem Solution No Power If the power supply is connected to the vehicle accessory circuits but the engine is not on, switch the ignition key to “ACC” No AM/FM Reception Antenna cable not connected; insert antenna cable firmly. No Sound Check volume level; increase volume if necessary. Fuse may be blown. Replace with 10 AMP ATO fuse. Check power; make sure device is on. Check device; press the play/pause button to ensure unit is not in Pause mode.
MS30 SPECIFICATIONS General Power Supply Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . DC 12 Volts, Negative Ground Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-16VDC Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0” Diagonal, 3.3” Deep Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0” Diagonal, 4” Deep Weight . . . . .
ASA Electronics Corporation www.asaelectronics.com www.jensenheavyduty.com www.jensenmarinedirect.com/ ©2012 ASA Electronics Corporation v.
