VM9412 BAND Multimedia Receiver AS DISP CLOSE Installation and Operation Manual ANGLE / TILT BAND PICTURE WIDE AS DISP OPEN Enter Press Audio VM9412 PTY SRC REAR DIV RPT SCN ® video RDM STOP MUTE 160 Watts Peak Watts en Crête Vatios el Máximo 40W x 4
CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9412 Mobile Multimedia Receiver for maximum enjoyment. Preparation............................................................................................................................ 1 Installation ............................................................
ii
VM9412 PREPARATION Congratulations on your purchase of the Jensen VM9412 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9412 installed by a reputable installation shop.
VM9412 Optional Equipment Tools and Supplies • You will need these tools and supplies to install your VM9412: • • • NAV101 The VM9412 is "navigation ready." Before accessing any navigation features, you must purchase and install the NAV101 module. All installation and operating instructions will be included with the NAV101 navigation module. Once the NAV101 is connected and operating properly, the NAV source mode will become active.
VM9412 WIRING DIAGRAM the MediaLink and Satellite Connections diagram for more information * See about connecting a satellite receiver and an iPod (through the MediaLink). MediaLink Bus SAT Radio * Satellite Receiver Connections WHITE BLUE SAT L SUB.
VM9412 To Head Unit MEDIALINK AND SATELLITE CONNECTIONS SAT Radio SAT L SAT R *SAT Cable Kit: JXMC or XMDJEN100 (sold separately) MediaLink **XM or Sirius satellite tuner (sold separately) 3.
VM9412 INSTALLATION Pre-installation 1. Press the metal levers on both sides to remove the halfsleeve from the radio. PREPARE RADIO FINAL INSTALLATION CAUTION! Be careful not to damage the car wiring. 3. 4 5 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. 1 Wiring Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal.
VM9412 ANTI-THEFT FEATURE The VM9412 is equipped with an anti-theft feature requiring the user to enter a password upon initial power on. The default user password is 012345 (6 digits). To change the anti-theft and RATINGS protection password, perform the following steps: 1. Press the SETUP button (31) on the remote control or 2. touch the button on the screen to enter the “SETUP” menu. Touch RATINGS to view the “RATINGS” sub-menu. The small "lock" icon will be “unlocked”.
VM9412 CONTROLS AND INDICATORS Button Operation 1. OPEN/CLOSE 4 3 BAND AS 7 2 1 Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. DISP Press to cycle through information available on the LCD screen. DISP OPEN 3. AS 4. BAND 5 16 Enter Press Audio Press to automatically store the first six strong stations in preset memory. Applies to current band only.
VM9412 CONTROLS AND INDICATORS 13.Pause/Play/Enter 7 3 4 Press to pause or resume playback or to confirm current selection. 2 1 14. (right joystick) DVD/Disc Mode: Press once to enter the next chapter or track. BAND TUNER Mode: Press once to auto-search the next available radio station. Multimedia Receiver AS DISP CLOSE MENU Mode: Press once to move the cursor to the right. 15. (up joystick) DVD/Disc Mode: Press once for fast forward/fast reverse. TUNER Mode: Press to go up one frequency step.
VM9412 REMOTE CONTROL The VM9412 Remote controls both the front and rear zones. To switch from front to rear zone, move the F/R switch (32) located on the right side of the controller. 30 8 4 35 31 14 16 18 17 19 15 32 2 3 22 1 13 11 5 9 12 24 23 28 25 20 21 10 27 29 26 6 7 33 34 NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.
VM9412 Table 1: Remote Control Functions Button Name Function Ref# DVD VCD TUNER CD/MP3 SATELLITE MENU 1 Enters the main menu of the disc Turns on/off PBC when playing VCD Displays diagnostics screen TITLE 2 Enters the title menu of the disc Plays first ten seconds of each chapter/title Category list in CG mode iPod MUTE 3 Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio o
VM9412 Table 1: Remote Control Functions Button Name Function Ref# DVD VCD TUNER CD/MP3 SATELLITE iPod PIC 24 Displays Brightness/Contrast Controls Displays Brightness/Contrast Controls Displays Brightness/Contrast Controls Displays Brightness/Contrast Controls Displays Brightness/Contrast Controls Displays Brightness/Contrast Controls OPEN/ CLOSE 25 Opens/closes the TFT monitor Opens/closes the TFT monitor Opens/closes the TFT monitor Opens/closes the TFT monitor Opens/closes the TFT
VM9412 USING THE TFT MONITOR Open/Close TFT Monitor Monitor Left/Right Angle Adjustment Aspect Ratio Open TFT Monitor To manually adjust the left/right angle of the TFT screen, follow these steps: Press the WIDE button (28) on the remote control or WIDE button (23) on the monitor to adjust the aspect ratio as follows: Press the OPEN button (1) on the front panel or press the ( ) button (25) on the remote control to activate the mechanism that moves the display panel into the viewing position. 1.
VM9412 Parameter Adjustment Procedure 1. Enter Picture Quality Setting Mode: Press the PIC button (24) on the remote control or the WIDE/PICTURE button (23) on the monitor. 2. Select Item to Set: Use the up/down joystick buttons to select “BRIGHT” or “CONTRAST”. 3. Set Parameters: Use the left/right joystick buttons to modify the settings. 4.
VM9412 OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (6) on the unit (or the /POWER button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. CAMERA and NAV.
VM9412 MULTI-ZONE OPERATION Independent sources can be played simultaneously on the VM9412. For example, a video game console can be seen on the front screen while DVD video is available to rear passengers. Changing the Rear Zone Source Turning the Rear Screen Off To access the SOURCE MENU, touch the TFT screen in the top left corner of the screen. Touch the OFF button (on the SOURCE MENU) to suspend operation of the rear screen.
VM9412 SETUP MENU To access system settings, press the SETUP button (31) on the remote control or touch the button on the screen to enter the “SETUP” menu. The “GENERAL” sub-menu appears highlighted in blue. RADIO SETUP General Language RDS Rating DivX Hardware P.
VM9412 Setting Tuner Region Options USA America 1 Arabia China America 2 Europe Korea OIRT (International Radio and Television Organization) Function AM Frequency Spacing - 10kHz AM Frequency Band 530kHz~1720kHz FM Frequency Spacing - 200kHz FM Frequency Band 87.5MHz~107.9MHz AM Frequency Spacing - 10kHz AM Frequency Band 530kHz~1720kHz FM Frequency Spacing - 100kHz FM Frequency Band 87.5MHz~108.0MHz only by entering the correct password.
VM9412 TUNER OPERATION Tuner TFT Display 8 1 17 RADIO 4 FM-1 2 24 25 3 01:02 PM P1 87.5 MHz ST E Q 10 5 LOC P1 87.5 MHz P2 90.1 MHz P3 98.1 MHz P4 106.1 MHz P5 107.9 MHz P6 102.9 MHz PTY RDS BAND 6 20. : Touch to view the SETUP menu 21. PS (Preview Scan): Touch to scan all stations available, stopping for 5 seconds at each and continuing until a station is selected 22. LOC: Touch to tune to strong local stations 23.
VM9412 close the menu). The preset number and station appears highlighted. Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (6) to select the corresponding stored station. P1 87.5 MHz P2 90.1 MHz P3 98.1 MHz P4 106.1 MHz P5 107.9 MHz P6 102.9 MHz Auto Store (AS) To select six strong stations and store them in the current band: 1. 2. Select a band (if needed).
VM9412 SATELLITE RADIO OPERATION Listeners can subscribe to XM® Radio on the Web by visiting www.xmradio.com, or by calling (800) 967-2346. Customers should have their Radio ID ready (see “Displaying the Identification (ID) Code”). Customers can receive a limited number of free-to-air channels without activation. Listeners can subscribe to Sirius® Radio on the Web by visiting www.sirius.com, or by calling (888) 539-SIRIUS.
VM9412 SAT E Q SAT1 XM Preview 01:02 CH001 Preview ######## 001 XM Preview CH 004 The 40s 005 The 50s CG 006 The 60s CAT 007 The 70s Title: www.xmradio.com • • • • • SCN MEM DIAG While in Search Mode, to switch between Channel and Category search modes, press the CH or CAT buttons on the touch screen. Use the scroll bar and arrows on the touch screen to view the next/previous page of stations. Each page contains six channels to select from.
VM9412 DVD/VCD VIDEO OPERATION Controlling Playback NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “PARKING” with a blue background. Rear video screens, if applicable, will operate normally. To access the on-screen controls, touch the screen.
VM9412 Direct Chapter / Track Selection Zooming • Remote Control Direct Entry Press the PRESET /\ and \/ buttons (11, 12) on the remote control to enlarge and pan through the video image using the following options: “ZOOM 1.5”, “ZOOM 2”, “ZOOM 3”, and “OFF”. The following information is displayed at the bottom of the screen: During DVD, VCD and CD playback, you can use the numeric keypad on the remote control (29) to access a track directly.
VM9412 General Disc Information Table 5: Disc Properties Symb ol 12cm Disc Properties Max Play Time Single side single layer (DVD-5) Single side double layer (DVD-9) Double side single layer (DVD-10) Double side double layer (DVD-18) (MPEG 2 Method) 133 minutes 242 minutes 266 minutes 484 minutes Single side single layer (VCD) (MPEG 1 Method) 74 minutes Single side single layer 74 minutes Table 6: Disc Symbols Symbol Meaning Number of voice languages recorded.
VM9412 DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9412 will play music or other audio files from the following disc media: • • • • • CD-DA CD-R/RW DVD DVD+R/RW DVD-R/RW E Q 2 1 1 Track 01 2 Track 02 01:23 4 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
VM9412 MP3/WMA/iPod OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. MP3/WMA Media and File Requirements This player allows you to play back MP3 and WMA files recorded onto CD-R/RWs, DVD+R/RWs, and DVD-R/RWs. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent illegal disc operation.
VM9412 16. Touch for quick access to Equalizer level settings 17. Touch to view the SOURCE MENU and select a new playback source 18. Folder name 19. 1/2 or 2/2: Touch this page button to view a second page of on-screen buttons 20. Touch the scroll bar and arrows to view the previous/ next page of songs 21. Touch to activate/deactivate Repeat play mode 22. Touch to access the Music menu 23. Touch to access the Video menu 24. Touch to access the Photo menu 25.
VM9412 Direct Track/File Entry To select a track/file directly, touch the control to display the direct entry menu. button on screen TRACK: _ _ _ 1 2 3 4 5 6 7 8 9 Exit Enter 0 Clear Enter the desired track/file using the on-screen number pad. Press the Enter button to tune to the selected station. To exit the screen without changing the station, touch Exit. To clear your entry and start over, touch Clear.
VM9412 TROUBLESHOOTING Table 7: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on Remote control does not function No/low audio output Poor sound quality or distortion Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right corner of the front panel Battery depleted Replace battery with new one Battery installed incorrectly Remove batter
VM9412 Table 7: Troubleshooting Problem Disc does not play back Cause Corrective Action Disc is warped or scratched Use disc in good condition Disc is dirty or wet Clean disc with soft cloth Laser pickup is dirty Clean laser pickup with cleaning disc Incompatible disc is used Use compatible disc Disc rating exceeds Parental Lock rating limit Change Parental Lock settings to lower restriction Disc region code is not compatible with unit Use disc with proper region code Disc is inserted upside
VM9412 Care and Maintenance 1. 2. 3. 4. 5. 6. 7. 8. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and nonneutral detergent (such as alcohol) may result in scratching or discoloration. Do not get water or cleaning fluids on the unit. If the temperature inside the player gets too hot, a protective circuit automatically stops play of the disc. If this occurs, allow the unit to cool before operating the player again.
VM9412 SPECIFICATIONS DVD/CD Player Compatible Disc Media: DVD +/- R/RW (Single and Dual Layer) and CD-R / RW Compatible Media Formats: CD-DA, MP3, WMA, VCD, SVCD, AVI, MPEG1 / 2, XviD, DivX and Kodak picture CD (JPEG).
Limited Warranty DO NOT RETURN THIS PRODUCT TO THE STORE CD or Multimedia Radios/Headunits Audiovox Electronics Corporation (“the Company”) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800323-4815 with any questions. Who is covered? The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or Canada.
Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensen.com © 2007 Audiovox Ver.