* PLEASE READ CAREFULLY BEFORE USING. CSW5007Q MULTI CAMERA CONTROLLER FOR OBSERVATION MONITOR (MULTIPLE DISPLAY MODE) V T U A V-O A IR ce -r ei ve r IN V A AV- A1 C Co ntr ol B A2 C ox A3 C A4 C ER W U 2V PO NTP ~3 I 0V 1 C D Doc.Rev (2007/05/07) * Design and Specifications are subject to change without notice.
Owner's Record The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No.: Serial No.: To prevent fire or shock hazard,do not expose the unit to rainor moisture. To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only.
INDEX FEATURES ----------------------------------------------------------------------- 4 PRECAUTIONS ----------------------------------------------------------------- 5 SYSTEM CONNECTIONS---------------------------------------------------- 6 INSTALLATION ----- ------------------------------------------------------------ 7 OPERATIONS -------------------------------------------------------------------- 8~12 SPECIFICATIONS --------------------------------------------------------------- 13 3
FEATURES CSW5007Q is designed to be compatible with most voyager observation monitors and cameras.
PRECAUTIONS Safety - Use only DC 10V to 32V. - In case that dust or liquid was soaked into the case, please turn off power and consult an experienced technician before using. - Install in a well ventilated area. Installation - Do not install the unit in an extremely hot or humid place (radiator, air duct, etc.) or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
MONITOR (Not supplied) Remote control sensor RCA plug or jack (A/V) RCA CABLE (supplied) RCA plug (A/V) A V IR-receiver A V AV-IN AV-OUT CSW5007Q CONTROL BOX Control Box CA1 CA2 WIRE COLOR DESCRIPTION 1 RED POWER IN + 12VDC 2 BLUE CAMERA/TRIGGER 1 3 BROWN CAMERA/TRIGGER 2 REF 4 YELLOW SPLIT SCREEN TRIGGER 5 BLACK GROUND-12VDC 6 ORANGE CA3 CA4 POWER INPUT DC10V~32V CAMERA/TRIGGER 4 7 GREEN CAMERA/TRIGGER 3 8 PURPLE* MONITOR TRIGGER OUT * This wire connects to reverse w
INSTALLATION Install the control box on a place which can hold more weight than 5 Kgs (11 lb). Fasten the control box with the provided screws as the drawings below. Mounting on the floor, console, etc. Jack Bracket Fasten the jack bracket with provided screws after connecting the cameras.
OPERATION Remote Control 1 4 * When the trigger signal is activated, the selected source's image will be displayed on the monitor screen automatically. (Please refer to TRIGGER MODE in SETUP MENU for further information) 1 5 3 2 POWER button - Press POWER button to turn the control box on or off. 2 6 3 - / + button - Press - / + button to adjust BRIGHT or CONTRAST level. - Press - / + button to select the content of the selected line in each sub menu.
OPERATION 6 MENU button - Press MENU button for less than 0.5 second to go to BRIGHT or CONTRAST mode. Use - / + button to adjust BRIGHT or CONTRAST level. ( BRIGHT CONTRAST BRIGHT... ) - Press MENU button for over 1 second to enter into SETUP MENU. Use UP / DOWN to move up and down and use - / + button to move left and right in SETUP MENU and each sub menu. - Press MENU button to go back to the previous menu when in SETUP MENU or each sub menu.
OPERATION 2. NORMAL / MIRROR CAM1: [NORMAL, MIRROR] CAM2: [NORMAL, MIRROR] CAM3: [NORMAL, MIRROR] CAM4: [NORMAL, MIRROR] - Move cursor up or down by pressing UP / DOWN button - Press CH.SELE button to select CAM1, CAM2, CAM3 or CAM4 - Select normal or mirror by pressing - / + button in the selected camera - Exit from the menu by pressing MENU button 3. TRIGGER MODE - Move cursor up or down by pressing UP / DOWN button TRIGGER SOURCE TIRGGER DELAY - Press CH.
OPERATION 4. SCREEN SPLIT - Move cursor up or down by pressing UP / DOWN button SPLIT 2 - Press CH.SELE button to select SPLIT2, SPLIT3 or SPLIT4 SPLIT 3 SPLIT 4 - Exit from the menu by pressing MENU button SPLIT2 SOURCE1: [CAM1,CAM2,CAM3,CAM4] SOURCE2: [CAM1,CAM2,CAM3,CAM4] AUDIO : [CAM1,CAM2,CAM3,CAM4] - Move cursor up or down by pressing UP / DOWN button - Press CH.
OPERATION 6. SCALE MODE CAM1: [OFF, SCALE1, SCALE2] CAM2: [OFF, SCALE1, SCALE2] CAM3: [OFF, SCALE1, SCALE2] CAM4: [OFF, SCALE1, SCALE2] SCALE 1 SCALE 2 - Move cursor up or down by pressing UP / DOWN button - Press CH.SELE button to select CAM1, CAM2, CAM3, CAM4, SCALE1 or SCALE2 - Select scale OFF, SCALE1 or SCALE2 by pressing - / + button in each camera - Exit from the menu by pressing MENU button * The distance marker of SCALE1 and SCALE2 can be adjusted.
SPECIFICATIONS CSW5007Q Power input ...................... Power cons. ....................... Video system ...................... Camera input (4 CH) ............. A/V output (1 CH) ................. A/V input (1 CH) ..................... Operating temp. .................. Storage temp. ..................... Ambient condition ................. Vibration ............................. Dimension ........................... Weight ................................. Supplied acc'y .....................
Printed in Korea