XDA91RB, 92RB, 94RB INSTALLATION / OWNER’S MANUAL
XDA SERIES Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the amplifier where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
XDA SERIES Connection Descriptions NOTE: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used as a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the amplifier location.
XDA SERIES Audio Inputs and Controls XDA91RB 4 1 2 3 5 XDA92RB 4 1 2 3 5 XDA94RB 4 2 2 1 Line Output 2 Line Input 3 High Level Input 4 Reset 4 3 5 5 Do not place anything in this area that could block the radio waves, as this may be a problem with your Bluetooth connection.
XDA SERIES Power and Speaker Connections XDA91RB 1 2 3 4 5 2 3 4 5 2 3 4 5 6 XDA92RB 1 6 XDA94RB 1 6 1 Power/Protect LED 4 +12V DC Battery Connection 2 Ground Connection 5 Fuse(s) 3 Remote Turn On 6 Speaker Connections 5
XDA SERIES Typical Wire Routing XDA91RB 6
XDA SERIES Typical Wire Routing XDA92RB 7
XDA SERIES Typical Wire Routing XDA94RB 8
XDA SERIES Amplifier Connections Speaker Connections Connect speaker wires observing polarity. The minimum impedance load for the amplifiers is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The amplifiers can be wired for stereo, bridged or stereo/ bridged simultaneous operation.
XDA SERIES Controller App Download/Installation Scan the above QR Code to download the Jensen Octane DSP Amplifier Controller app from the Apple App Store or Google Play Store onto your smartphone or tablet. Use the app to control features including: X-Over, EQ, RGB Light Customization, Volume and other amp settings directly from your smartphone or tablet via Bluetooth. Note: XDA amp series do not support audio streaming and hands free calls via Bluetooth.
XDA SERIES Bluetooth Paring with App and AMP 1 3 4 5 2 6 Step 1 : Touch the BT icon 1 Step 2 : Touch the Scan icon 2 to search the Bluetooth amp. Step 3 : Bluetooth amp list 3 to show what amp is paired. (If only one amp is installed, one amp model number is displayed.
XDA SERIES JENSEN DSP AMP App Operation Input level Control (Master Level at HOME Mode) X-OVER Mode The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise to provide the best match.
XDA SERIES Specifications XDA91RB Power Output •240 Watts RMS x 1 channels @ 4 Ohms •400 Watts RMS x 1 channels @ 2 Ohms •600 Watts RMS x 1 channels @ 1 Ohm Peak Music Power Output: 1200 Watts Signal to noise ratio: 68dBA (reference : 1 Watt into 4 Ohms) Frequency response: 20Hz– 250Hz Amplifier dimensions: 2.16” x 9.56” x 5.
XDA SERIES Troubleshooting Problem Cause +12V wire not connected or incorrect Unit will not turn on voltage.
XDA SERIES One-Year Limited Warranty Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Namsung America Inc.
XDA SERIES FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
XDA SERIES Note 17
XDA SERIES OWNER’S MANUAL The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. Other trademarks and trade names are those of their respective owners. Customer Support 1-888-921-4088 (Monday-Friday, 9AM-5PM EST) Visit https://www.jensenmobile.com Designed and Engineered in USA Namsung America Inc. ©2020 Namsung America Inc. All rights reserved. All rights reserved.
