Model Number: CAS75206W CAB75206W CAS75206P CAB75206P CAB75206 CAS75206 www.ciarraappliances.
Dear customer: Thank you so much for your purchase, please read this instruction manual carefully before installation & use. If you have any question, please contact us at: E-mail: info@ciarraappliances.
CONTENTS Safety--------------------------------------------3-4 Specifications--------------------------------------5 Before Using the Range Hood----------------------6 Prepare for Installation ----------------------------7 Installation--------------------------------------8-16 Install the Hood-------------------------------------------8-15 Carbon Filter Installation ------------------------------------16 Operation --------------------------------------18-29 Push Button--------------------------------------
Safety ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. Before servicing or cleaning unit, unplug or disconnect the range hood from the power supply.
Safety ! WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN — You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels — This could cause a violent steam explosion. 4.
Specifications CAS75206P CAB75206P CAS75206 CAB75206 CAS75206W CAB75206W SKU CAS75206P CAB75206P CAS75206 CAB75206 120V/60Hz Voltage 1 x 200W Power of Motor Power of lamps Appliance Dimension CAS75206W CAB75206W 2 x 3W 2 x 1.5W 2 x 1.5W 29.53*18.5*25.28-40.16(inches) 29.53*19.69*25.28-40.16(inches) (W x D x H) Note: The manufacturer reserves the right to change any technological improvement or modification without prior notice.
Before Using the Range Hood CAUTION: Before proceeding to the installation, check If items are missing or damaged, contact the manufacturer. Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate.
Prepare for Installation Prepare for Installation: a) Ventilation Mode Recirculation Mode: Recirculating with carbon filter (required), the smells and odors can be filtered and vented through the top vented hole and the exhaust pipe is not required. Extraction Mode: You can install the 59" long and 6" diameter aluminum exhaust pipe for extracting, which is included in the installation kit. b) When possible, use at least 2 foot straight runs before any turns.
Installation Install the Hood（Extraction）: 1) Remove all protective poly film from the hood and/or parts. 2) Recommend installation height: 25.6"~29.5" above the cooktop for best extraction. Required height over gas hob: 29.5"; Required height over electric hob: 25.6". 25.6" 29.
Installation 3) First use a pencil to mark the installation position on the wall, then use a Measuring Tape to measure the height from the stove surface to the hood (the center point of aluminum grease filter) and use a Spirit Level Ruler to maintain the level, then use a pencil to draw a horizontal line along the level. Spirit Level Ruler 25.6" 29.
Installation 5) Determine the maximum chimney installation height according to the actual scenario and mark the chimney installation locations along the center line of the Installation Diagram. Chimney installation locations 6) Remove the Installation Diagram, drill the holes that have been marked on the wall with an Electric Drill (8mm drill), and hammer the Wall Plug into the wall.
Installation 7) Use three 0.16"*1.18" Screws to fasten the Wall Bracket on the wall. 0.16"*1.18" Screws 0.16"*1.18" Screws COMPONENTS: Part 2: 0.16"*1.18" Screws X 3 Part 10: Wall Bracket X 1 8) Remove the aluminum grease filter and hang the hood on the corresponding hook of the Wall Bracket.
Installation 9) Use a Spirit Level Ruler to measure whether the hood is in a horizontal level, and use two 0.16"*1.18" Screws to lock into the safety hole position of the hood (not mandatory, according to user's wishes to choose whether to lock). 0.16"*1.18" Screws Spirit Level Ruler COMPONENTS: Part 2: 0.16"*1.18"Screws X 2 10) Tear off the tape from the air outlet.
Installation 11) Install the Aluminum Exhaust Pipe into the air outlet and lock it with a Cable Tie; the other end of the Aluminum Exhaust Pipe will be pulled upward to outdoor and lock it with a Cable Tie (Note: This step can be ignored if use as recirculation mode with carbon filter). 6" Aluminum Exhaust Pipe Cable Tie COMPONENTS: Part 4: Aluminum Exhaust Pipe X 1 Part 5: Cable Tie X 1 12) Use two 0.16"*0.32" Screws to fasten the Lower Chimney Bracket on the Lower Chimney.
Installation 13) Insert the Lower Chimney into the hood and fix it to the corresponding positioning hole with two 0.16"*0.32" Screws. (Note: That the power cord needs to go through the chimney and connect the power). COMPONENTS: Part 3: 0.16"*0.32" Screws X 2 Power Plug 0.16"*0.32" Screws 14) Use two 0.16"*1.18" Screws to lock the Lower Chimney Bracket into the corresponding positioning holes on the wall. 4*30mm Screws COMPONENTS: Part 2: 0.16"*1.
Installation 15) Use two 0.16"*1.18" Screws to lock the Upper Chimney Bracket to the corresponding positioning holes on the wall. COMPONENTS: Part 9: Upper Chimney Bracket X 1 Part 2: 0.16"*1.18"Screws X 2 0.16"*1.18" Screws 16) Put the Upper Chimney into the Lower Chimney, and then pulled to the height of the Upper Chimney Bracket.
Installation 17) Use two 0.16"*0.32" Screws to assemble the Upper Chimney on the Upper Chimney Bracket. COMPONENTS: Part 3: 0.16"*0.32" Screws X 2 0.16"*0.32" Screws Upper Chimney Bracket 18) Turn the LED lights on/off, and test whether the functions are working properly.
Installation Carbon Filter Installation（Recirculation）: 1. Carbon filter can be used to trap odors. In order to install the carbon filter, the grease filter should be detached first. Press the lock and pull it down. 2. Place the carbon filter into the unit and turn it in the clockwise direction to lock it in place. 3. If the carbon filter needs to be replaced, please turn it in the anticlockwise direction. NOTE: Make sure the carbon filter is securely locked.
Operation Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Operate the hood as follows: SKU Control CAS75206P CAS75206 CAS75206W CAB75206P CAB75206 CAB75206W Push Button Touch control CAS75206P Touch+Wifi+App+Voice control with ALEXA and Google Home CAB75206P Push button Off button It's used to turn off the fan. Low Speed button For air ventilation with barely no noise; or simmering with very little smoke and steam.
Operation CAS75206W CAS75206 CAB75206W CAB75206 Touch control Power key: It's used to turn on/off the power. Press 2S to power on, press 1S to power off. Added level key: Indicator show level adjustment 1-2-3-0-1, Show 0 for turning off, Loosen hand turn off orange color out-ring delay 5 seconds. Reduced level key: Indicator show level adjustment 3-2-1-0-3, Show 0 for turning off, Loosen hand and delay 5 seconds turn off orange color out-ring.
Operation Delay function: When range hood working, could set delay function. Push first time and indicator show1, for delaying 5 minutes; Push second time and indicator show 2, for delaying 10 minutes; Push third time and indicator show 3, for delaying 15 minutes; Push fourth time and indicator show 4, for delaying 20 minutes; Push fifth time and indicator show 0, after 5 seconds in level 0 and drop out delay function automatically.
Operation Smart Life APP (Only support CAS75206W and CAB75206W) Download and Intallation of Smart Life APP 1. You must use Android phone or iPhone to download and use this APP. 2. Search “Smart Life” in the Google Play store for Android or IOS App Store to download and install the APP. Video Guide Range Hood and Smart Life APP pairing 1. When you log in to Smart Life APP for the first time, you need to create a new account. When creating a new account, follow the app prompts to register. 2.
Operation 1. Open the smart life 2. Choose kitchen 3. Choose kitchen hood. app, Click Add Device. appliances from the menu bar on the left. 4. Connect your home Wi-Fi and enter the password, then click Confirm. 5. Click "Next" to go to the next step. 22 6. Press 2S to power on,and press the “Delay function+WIFI” button for 5 seconds, you will hear the beeping sound, and all orange out ring lights will be flashing, enter Wi-Fi pairing mode.
Operation 7. Click “Blink Quickly” and click “Next”. 8. Adding device... 9. When you see this interface it means you have successfully connected your device. 10.Click "Me" and select "Home Management". 11. You can create a home or join a home in this area. Click "my family management". 12. Select "Add members" and share to members, after members are successfully join the same family, they can remotely control "Range Hood" .
Operation Voice control with ALEXA (Only support CAS75206W and CAB75206W) 1. Precondition: You must have internet access, your devices should be connecting to the same Wi-Fi network. An Echo device, including Echo, Echo Tap, or Echo Dot. Amazon account, if you do not have one; please register one first. Have “Smart Life App” and account. P.
Operation 4. Enter "Smart Life" in 5. Click "ENABLE TO USE" the search box, find to go to the next step. "Smart Life" (the icon as shown in diagram) in the search list, and click to go to the next step. 6. Click on "Agree and link" to go to the next step. 7. When "Your Smart Life account has been successfully linked" is displayed, click "CLOSE" to go to the next step. 9. Click to enter the"Devices" interface. 8. Click on "CANCEL" to go to the next step.
Operation 10. When"1 Fan appears" is displayed, click "View "to go to the 11. Click on "Range Hood" to go to the next step. next step. 12. Now that the Range Hood has been added successfully, you can remotely control various functions of the Range Hood on this interface, or use Alexa Echo to voice control the Range Hood. 5.
Operation Voice control with Google Home (Only support CAS75206W and CAB75206W) 1. Precondition: Before controlling the device with Google Home, please make sure you meet the following terms: You must have internet access, your devices should be connecting to the same Wi-Fi network. One Google Home device or an Android phone with Google Assistant. Newest version of Google Home App. Newest version of Google App (only for Android). You must have a google account.
Operation 4. Enter "Smart Life" in the search box, perform your search. 7. Click on "Agree and link". 5. Find "Smart Life" (the icon as shown in diagram) in the search list,click to go to the next step. 6. When "Linking your Smart Life account" is displayed,the page will loads to the next step. 8. The Home page of Google Home shows the name of the added device "Range Hood". Now that the device has been added successfully, you can use Google Voice Assistant to control your Range Hood.
Operation 5. Notice: "DISCOVER DEVICES" can only discover those devices which have been paired with the "Smart Life App" When you change the name of the device in the "Smart Life App", Google home has to rediscover the device, otherwise you can not control it. 6. Voice control devices Now, you can use Google Home to control your device. You can control your range hood through the following: Hey Google, turn on/off .
Cleaning and Maintenance Proper maintenance of the Range Hood will assure proper performance of the unit. Before cleaning unit, unplug or disconnect the range hood from the power supply. GREASE FILTERS The grease filters should be cleaned frequently. Can be cleaned in dishwasher under high temperature without using any detergent. CARBON FILTER The carbon filter should be changed every 2-4 months depending on the conditions of use.
Cleaning and Maintenance LED REPLACEMENT Rectangle LED lamp: CAUTION： Before cleaning or repairing and replacing accessories, please make sure to shut down the power before operation, so as to avoid electric shock, damage to human body and even endanger life safety! 1. Turn off the hood and unplug the power outlet. Detach the grease filter in order for you to replace the LED lamp. 2.
Cleaning and Maintenance 3. Open the power protection cover, pull out the plug and replace the corresponding model of the LED lamp. 4. Turn the power on and test all blower and light functions to ensure they areoperating properly. Insert the new LED light gently into the light socket, please make sure you aim at the grooves on the lighting panel when installing. Push the LED light in until it is flushed with the light panel. 5. Put the grease filter back on, you are good to go.
Troubleshooting Problem Extractor hood does not turn on Possible Cause No electrical supply Make sure that range hood is plugged into powered outlet.
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
