This Manual is Bookmarked Operating Instructions and Parts Manual Dust Collector Model: DC-1100A/C/RC DC-1100A/RC WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www.wmhtoolgroup.com DC-1100C/RC Part No.
This manual has been prepared for the owner and operators of JET DC-1100 Series Dust Collectors. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Warranty and Service WMH Tool Group warrants every product it sells.
Table of Contents Warranty and Service ........................................................................................................................................... 2 Table of Contents.................................................................................................................................................. 3 Warnings ............................................................................................................................................................
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only.
blahblahblah 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector. 23.
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual.
Unpacking DC-1100A/RC Dust Collector 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly.
Unpacking DC-1100C/RC Dust Collector 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly.
Assembly Base 1. Install four casters to the under side of the base as pictured in Fig. 2. 2. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 14mm wrench. This will give the caster proper clearance. Figure 1 Motor and Fan Assembly 3. Place the base with casters on the ground.
Connector Housing 5. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. Figure 4 6. Install the housing (A, Fig. 5) to two support brackets (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. 7. Before attaching third support bracket place the hanger bracket (D, Fig.5) between the support bracket and the housing.
Filter Bag Installation – DC-1100A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). Figure 7 Collector Bag Installation – DC-1100A/RC Referring to Figure 8: 4. Insert the ring of the collector bag (A) at an angle into the housing (B) through the opening at the bottom.
Collector Bag Installation – DC-1100C/RC 1. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 9. Figure 9 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle. 3. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the snap ring “snaps” into place in the housing, and also that the plastic bag hangs down approximately 3” so that there are no air leaks.
time will scroll up to 99 minutes, then start again at 00. Release the button when the desired set time is reached. The dust collector will run for the amount of time displayed on the digital display. If you scroll past 99 and release the button at 10, for example, the machine will run for ten minutes, not 110 minutes. Electrical Connections All electrical connections must be done by a qualified electrician.
Cleaning the Filter – DC-1100C/RC Maintenance Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Clean both the filter and collector bags frequently to keep the collector's performance at its optimum.
Parts List – DC-1100A/RC Dust Collector Index No. Part No. Description Size Qty 1 ............... 411035W ................. Impeller Housing.....................................................................................................1 2 ............... 411026W ................. Motor Bracket .........................................................................................................1 3 ............... 998621..................... Strain Relief ........................................
Parts Breakdown – DC-1100A/RC Dust Collector 16
Filter Assembly for DC-1100C/RC Models Index No. Part No. Description Size Qty 1 ............... 331050..................... Handle ....................................................................................................................1 2 ............... TS-1540071............. Hex Nut.................................................................M10 ..........................................2 3 ............... TS-1550071............. Flat Washer ..........................................
Remote Control Breakdown for DC-1100RC Index No. Part No. Description Size Qty ................. DC1100RC-100 ....... Receiver Assembly (Items 1-12) ............................................................................1 1 ............... DCRC-101 ............... Label .......................................................................................................................1 2 ............... DCRC-102 ............... Counter Screw.......................................................
Wiring Diagram – DC-1100A/C 19
Wiring Diagram – DC-1100RC 20