This Manual is Bookmarked Operating Instructions and Parts Manual Dust Collector Model: DC-650A/C/ARC/CRC DC-650ARC shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www.wmhtoolgroup.com DC-650C shown Part No.
This manual has been prepared for the owner and operators of the JET DC-650 Series Dust Collectors. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Warranty and Service WMH Tool Group warrants every product it sells.
Table of Contents Warranty and Service ........................................................................................................................................... 2 Table of Contents.................................................................................................................................................. 3 Warnings ............................................................................................................................................................
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only.
blahblahblah 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector. 23.
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for models DC-650 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual.
Unpacking 1. Remove all contents from the shipping carton. DC-650C Contents 2. Report any damage to your distributor. Canister Filter Box 1 – Canister Filter 1 – Handle 1 – Bag of Hardware for Handles 2 – M10 Hex Nuts 2 – M10 Flat Washers 1 – M10 Lock Washer 4 – Knobs 1 – M8 Hex Nut 1 – M8 Flat Washer 1 – M8 Lock Washer 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly.
Assembly The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! Motor Housing and Support Canister 1. Place the impeller housing (A, Fig. 1) on the floor with the motor (B, Fig. 1) facing upwards as shown. 2. Attach the fan (C, Fig. 1) to the motor shaft (D, Fig. 1). Allow a 1/16"-1/8" clearance between the fan (C, Fig. 1) and housing (E, Fig. 1). Figure 1 3. Secure the fan (C, Fig.
Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 flat washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housing and tighten nut against the housing. 2. Place the retaining strap (C, Fig. 5) through the loops on the filter bag and hang the filter bag from the hook. 3. Secure bag to housing with retaining strap. Note: The retainer strap should be tight enough to provide a good seal.
Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig. 7), and a M8 hex nut (F, Fig. 7). 3. Thread a M10 hex nut (G, Fig. 7) onto the threaded rod found on top of the canister filter followed by a M10 lock washer (H, Fig. 7), and M10 flat washer (I, Fig. 7). 4. Mount the arm (C, Fig.
reached. The dust collector will run for the amount of time displayed on the digital display. If you scroll past 99 and release the button at 10, for example, the machine will run for ten minutes, not 110 minutes. Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged.
Maintenance To reduce the risk of injury from moving parts, always keep the inlet connected to the flexible hose. Failure to comply may result in serious injury! Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter – DC-650C/CRC Cleaning the Filter Bag – DC-650A/ARC Clean both the filter and collector bag frequently to keep the collector's performance at its optimum.
Parts Replacement Parts Replacement parts are listed in the Parts List on the following pages. To order parts or reach our service department, call 1-800-274-6848 between 7:00 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts List Index No. Part No. Description Size Qty 1 ............... 422109W ................. Impeller Housing......................................
Index No. Part No. Description Size Qty 35 ............. 331010..................... Shaft .......................................................................................................................1 36 ............. 331043..................... Scraper ...................................................................................................................2 37 ............. 331015..................... Plate............................................................................
Parts Breakdown for DC-650C/CRC Models for DC-650A/ARC Models 15
Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size Qty ................. DC650RC-100 ......... Receiver Assembly (Items 1-11) ............................................................................1 1 ............... DCRC-101 ............... Label .......................................................................................................................1 2 ............... DCRC-102 ............... Counter Screw..................................................
Wiring Diagrams DC-650A/C Models 115V 230V 17
DC-650ARC/CRC Models 18
Notes 19
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.