This Manual is Bookmarked Owner's Manual XACTA®Fence II Commercial 30/50 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Ph.: 800-274-6848 www.wmhtoolgroup.com Part No.
Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or ® perform routine maintenance and major repair on your JET tools. For the name of an Authorized Service Center in your area call 1-800-274-6848.
Table of Contents Warranty and Service.................................................................................................................................... 2 Table of Contents.......................................................................................................................................... 3 Warnings .......................................................................................................................................................
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. The Table Saw on which the XACTA Fence II is used is designed and intended for use by properly trained and experienced personnel only.
22. Make your workshop child proof with padlocks, master switches or by removing starter keys. 23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation. 25. Use the right tool at the correct speed and feed rate.
Unpacking Open shipping cartons and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly, alignment, and maintenance instructions. Contents of the Shipping Containers 1 1 1 1 3 1 1 1 XACTA Fence II Front Rail Rear Rail Guide Rail Black Plastic End Caps Hardware Package Owner’s Manual Warranty Registration Card The contents of the hardware bag are drawn full scale in Figure 1.
Installation Tools required 7/16" and 1/2" wrenches Cross point screwdriver 3/16" hex wrench Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for installing the XACTA Fence II and Rail System on JET Models JTAS-10, JTAS-12 and XACTA® Saw Deluxe series table saws. The rails should bolt up to the JET saw without any drilling. Front Rail Installation Referring to Figures 1 and 2: Figure 1 1.
Back Rail Installation 1. Locate the back rail which is 2" x 2" with holes running along one side only. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. Figure 4 3. Secure the back rail to the pre-tapped holes in the saw table (B, C, Fig. 4) with two 5/16 x 3/4 hex cap screws and two 5/16 flat washers, as shown in Figure 5. Tighten screws securely with a 1/2" wrench. Figure 5 4.
Wooden Extension Table The wooden extension table is an optional accessory. Tools required Electric drill Cross point screwdriver 7/16" and 1/2" wrenches Four clamps Straight edge Hammer (or rubber mallet) Figure 7 Installation The optional wood extension table (including the optional router table) sits flush against the saw table and along the inside of the rails. The JET logo (or warning label on the router table) should face outward.
as shown in Figure 10. Finger tighten only. 5. Install three 1/4-20 x 1-1/2 hex cap screws, three 1/4 flat washers, and three 1/4 nuts into the holes in the rear edge of extension table as shown in Figure 11. Finger-tighten only. 6. Re-check the table for alignment, make further adjustments if necessary, then tighten all screws and nuts. Figure 11 7. Mount the two legs to the inside corners of the extension table as shown in Figure 12. Secure with the eight screws provided.
XACTA Fence Screw the lock lever knob into the threaded handle on the XACTA Fence II as shown in Figure 14. The lock lever has three functional positions as shown in Figure 15: • • • The upright position permits mounting and removal of fence from the saw. The unlock position permits easy fence positioning. The lower position locks the fence to the front rail. The cam handle should be pushed down firmly against the pin. Figure 14 Leveling Fence to the Saw Table 1.
Adjusting Fence Parallel to the Miter Slot 1. Place the fence next to the outside edge of the right miter slot and lock it. 2. The fence should be even with the miter slot from front to back. 3. If the fence is not even along the length of the miter slot, unlock the fence, remove it and turn upside down. 4. Adjust one of the two setscrews (A, Fig. 18) until the fence is even with the miter slot edge along its entire length when locked.
Parts for the XACTA Fence II Commercial 30/50 Index No. Part No. Description Size Qty 1 ...............XF2-101 ...................Left Side Plate...................................................... .................................... 1 2 ...............XF2-102 ...................Fence Body Assembly ......................................... .................................... 1 3 ...............XF2-103 ...................Tube Cover .......................................................... ..........
Parts for the XACTA Fence II Rail Assembly Index No. Part No. Description Size Qty 1 ...............XF2-201 ...................Front Rail (50”)..................................................... .................................... 1 .................XF2-201A.................Front Rail (30”)..................................................... .................................... 1 2 ...............TS-081F081 .............Flat Head Screw ..................................................
Parts for the XACTA Fence II Leg Assembly Index No. Part No. Description Size Qty 1 ...............XF2-301 ...................Leg ....................................................................... .................................... 2 2 ...............TS-0561031 .............Hex Nut ................................................................ 3/8”-16......................... 2 3 ...............XF2-303 ...................Adjusting foot ....................................................... ...
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.
