OWNER'S MANUAL EHVS-80CS Edge Horizontal/Vertical Sander JET EQUIPMENT & TOOLS, INC. A WMH Company www.jettools.com P.O. BOX 1349 Auburn, WA 98071-1349 e-mail jet@jettools.
This manual has been prepared for the owner and operators of a JET EHVS-80CS Sander. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your sander, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully.
WARNING 1. Read and understand the entire instruction manual before attempting assembly or operation. 12. Make certain the switch is in the OFF position before connecting the machine to the power supply. 2. This sander is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a sander, do not use until proper training and knowledge have been obtained. 13. Give your work undivided attention.
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
230 Volt Operation WARNING! All electrical connections must be done by a qualified electrician! Failure to comply may result in serious injury! If 230V operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This sander is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3.
Specifications: EHVS-80CS Stock Number................................................................................................................................ 708448 Fence ....................................................................................................................................... 4”H x 24”L Abrasive Belt Size ................................................................................................................... 6”W x 89”L Dust Chute Diameter .................
Contents of the Shipping Container 1. 1. 2. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. Stand (front) Stand (rear) Stand (sides) Extension Table Assembly Extension Cover Owner’s Manual Warranty Card Sanding Unit with Motor Back Stop Handle Driver Wrench Miter Gauge Assembly Sanding Belt Adjusting Wrench Assembly Hardware: Cabinet 1. Lock Knob (20mm Length) 2. Lock Knob (12mm Length) 1. Lock Knob (35mm Length) 4. Cabinet Pads 4. 5/16” x 5/8” Screws 22. 5/16” Flat Washers 12. 5/16” Hex Nuts 8.
Assembly 1. Remove all contents from the shipping container. 2. Clean all rust protected surfaces with a mild solvent. Do not use paint or lacquer thinner, gasoline, or mineral spirits; these will damage painted surfaces. 3. Attach the four rubber pads (A, Fig. 1) to the bottoms of the side panels with four 5/16” x 5/8” Screws, four 5/16” flat washers and four 5/16” hex nuts (B, Fig. 1). The hardware can be found in the bag with the rubber pads. 4. Attach the side panels (C, Fig.
10. Sanding platen is presently in a horizontal position. Pull lock handle forward (A, Fig. 3) to unlock platen assembly, tilt sanding platen to the vertical position, and push lock handle to lock platen assembly in place. Note: do not turn lock handle. Turning or rotating the lock handle will change the tension of the locking assembly. This may cause the locking assembly not to work; making it necessary for adjustment before using the machine. 21. Reinstall the guards and secure in place with lock knobs.
WARNING Removing the belt guard exposes more of the sanding belt! Replace the belt guards immediately after completing any sanding that requires it’s removal! Failure to comply may cause serious injury! Horizontal Sanding With the sanding platen locked in the horizontal position, the removable fence (A, Fig. 6) may be used. The fence can be secured in place by screwing two lock knobs (B, Fig. 6) into the guide blocks found in the miter slot.
Platen Lock Tension Adjustment 1. Disconnect the machine from the power source. 2. Loosen lock handle by pulling forward (A, Fig. 9) and move motor and sanding table toward the horizontal position. Do not lock. 3. Tension eccentric block by tightening the nyloc nut (B, Fig. 9) with a 14mm wrench. Turn the nut in ¼ turn increments and test locking handle for proper tension.
3. Insert the driver with the round shaft, supplied with the machine into the micro adjusting nut (A, Fig. 11) and turn away from you to loosen. 4. Turn the micro adjusting screw (B, Fig. 11) in ¼ turn increments until the belt tracks evenly on the rollers when rotated by hand. 5. Tighten the micro adjusting nut (A, Fig. 11). 6. Connect the machine to power. 7. Turn on the power to the machine just enough to start the belt rotating and then turn off. Do this several times and observe belt tracking.
Table Adjustment WARNING Do not position table below sanding belt! Keep an overlap of at least 1/16” between table and sanding belt to avoid material and/or fingers getting caught! Failure to comply may cause serious injury! 1. Loosen two lock knobs (A, Fig. 13). 2. Raise or lower work table to desired level. 3. Tighten two lock knobs. Troubleshooting Trouble Possible Cause 1. Sander unplugged from wall or motor Sander will not start 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1.
Table and Motor Assembly 14
Parts List For The EHVS-80CS Sander Table and Motor Assembly Index Part No. No. Description Size Qty. 1..........EHVS80CS-01 ................. Base.............................................................. .................................1 2..........994532............................. Switch (serial #: 9031435 and lower) ............. .................................1 ............EHVS80-02N ................... Push Button Switch (serial #: 9031436 and higher) .........................1 3.........
Index Part No. No. Description Size Qty. 37A......EHVS80-37A.................... Pin................................................................. M6x40mm ................1 38 ........EHVS80-38 ...................... Spring............................................................ .................................1 39 ........EHVS80-39A.................... Spacer........................................................... .................................1 40 ........EHVS80-40 ......................
Index Part No. No. Description Size Qty. 109 ......EHVS80-109 .................... Label ............................................................. .................................1 110 ......EHVS80-110 .................... Pan Hand Screw ........................................... 3/16”x3/8” .................3 111 ......EHVS80-111 .................... Extension Cover............................................ .................................1 112 ......EHVS80-112 .................... Washer......
Stand Assembly Index Part No. No. Description Size Qty. 1..........TS-0680031 ..................... Flat Washer................................................... 5/16”......................... 22 2..........TS-0720081 ..................... Lock Washer ................................................. 5/16”......................... 10 3..........TS-0561021 ..................... Hex Nut ......................................................... 5/16”........................... 8 4..........EHVS80CS-S04..