Operating Instructions and Parts Manual SLT-660F/1650 Scissor Lift Tables For serial no. 17020001 and higher JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
Warranty and Service JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
Table of Contents Warranty and Service ............................................................................................................................................ 2 Table of Contents .................................................................................................................................................. 3 Specifications ....................................................................................................................................................
Assembly Note: The SLT-660F does not require any assembly. 1. On the SLT-1650, attach the handle (A, Figure 1) to the frame using two hex cap screws, two lock washers, two flat washers. Tighten with a 19mm wrench. Note: The two pivoting casters can be locked so that they do not rotate. Press foot lever (B, Figure 1 for SLT-1650) down to lock. Press foot lever (A, Figure 2 for SLT-660F) down to lock. 2.
Operation Maintenance 1. The table can be raised by pumping the foot lever. 1. Lubricate each friction point monthly with #2 tube grease. Note: You may need to raise and lower the table several times to work any air bubbles out of the pump. 2. Check the movement and wear of wheels. 3. Check for oil leakage from the hydraulic cylinder. Add hydraulic oil as needed. 4. Always store with table in lowered position when not in use. 2. To lower the table, pull the release lever fully.
Troubleshooting SLT-660F/1650 Scissor Lifts The numbers in parentheses refer to the appropriate breakdown, 660F listed first/1650 listed second. Trouble Probable Cause Remedy Oil level low in reservoir. Replenish reservoir. Lowering valve (28/29) or steel ball (25/26) is not seating. Clean lowering valve (28/29) or steel ball (25/26) or replace. Steel ball (13/14) is not seating. Clean or replace steel ball (13/14). Relief valve is not adjusted properly.
Parts Breakdown for SLT-660F Scissor Lift Table 7
Parts List for SLT-660F Scissor Lift Table Index No. Part No. Description Size Qty 1 ................ SLC660F-01G ........... Table ........................................................................ ...................................... 1 2 ................ SLT660F-06 .............. Link Shaft ................................................................. ...................................... 2 3 ................ SLC660F-02 .............. Link Assembly.........................................
Index No. Part No. Description Size Qty [20] ............ SB-5MM .................... Steel Ball.................................................................. Ø 5 mm ......................... 1 [21] ............ SLT660F-36-21 ......... Screw ....................................................................... M10 x 1 ......................... 1 [22] ............ SLT660F-36-22 ......... O-Ring* .................................................................... ...................................
Index No. Part No. Description Size Qty 73 .............. SLT660FH-73............ Hex Cap Screw ........................................................ M6 x 10 ......................... 1 74 .............. SLT660FH-74............ Spring Washer ......................................................... Ø 6mm .......................... 1 75 .............. SLT660FH-75............ Spring Clip ............................................................... ...................................... 1 76 ........
Parts Breakdown for SLT-1650 Scissor Lift Table 11
Parts List for SLT-1650 Scissor Lift Table Index No. Part No. Description Size Qty 1 ................ SLC1650-1G ............. Table ........................................................................ ...................................... 1 2 ................ SLC660F-38 .............. C-Ring...................................................................... Ø 20 mm ....................... 2 3 ................ SLC1650-2 ................ Link Assembly..............................................
Index No. Part No. Description Size Qty [19] ............ SLT660F-36-13 ......... Spring ...................................................................... ...................................... 1 [20] ............ SLT660F-36-14 ......... Steel Ball Support .................................................... ...................................... 1 [21] ............ SB-5MM .................... Steel Ball.................................................................. Ø 5 mm ......................
Index No. Part No. Description Size Qty 72 .............. SLT1650H-72 ............ Safety Bar ................................................................ ...................................... 1 73 .............. SLT660FH-72............ Hex Nut .................................................................... M10 ............................... 1 74 .............. SLT660FH-73............ Hex Cap Screw ........................................................ M6 x 10 .........................
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
