Use and Care Manual

HDT Series Manual Trolley – Installation and Safety Instructions

JET Manual Trolleys are designed to be used on either "Ι" or “H” wide flange beams.

JET HDT Series Trolleys comply with OSHA regulations, ANSI/ASME B30.11 and B30.17 standards.

IMPORTANT SAFETY INSTRUCTIONS

To reduce risk of injury:

1. Beam must be properly installed and rated for anticipated loads.

2. Do not install trolley on beams of unknown capacity.

3. Do not install trolley on damaged or deformed beams.

4. JET trolleys are designed to be used with hoists of the same rated capacity. Never use a hoist with a capacity

greater than the capacity of the trolley.

5. Never subject trolley to a side pull or load. Load must be centered directly under the hoist / trolley assembly.

6. Make sure load is stable and secure before moving.

7. Never lift load more than is necessary to safely move it.

8. Always follow installation instructions.

9. Do not use if under the influence of drugs, alcohol, or medication.

Installation Instructions

(refer to Figure 1)

1. Trolley must be installed on a beam with minimum

clearance (wheels to flange) of 1/16" to maximum of

1/8". Reference "Z" on both sides of the beam.

2. To extend trolley width, remove split pins and hex

nuts. Remove washers from center bolt and place

between hanger plate and fixed spacer. Note:

Washers must be moved in sets of two, one on

either side of hanger plate, as hanger plate must

always remain centered between trolley side plates.

3. Once trolley width is spaced properly, install

remaining washers on center bolt (same number on

both sides) on outside of side plates. Install hex nuts

and split pins. Do not over tighten nuts. Tighten

nuts and then back nuts off to align the nut with hole

in shaft for split pin. Insert split pin through each hex

nut and bend one end of split pin to secure.

4. Re-check wheel clearance "Z" and re-adjust if

necessary

Figure 1

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-262005

Ph.: 800-274-6848 Revision C 11/2017

PAGE 1
HDT Series Manual Trolley – Installation and Safety Instructions JET Manual Trolleys are designed to be used on either "Ι" or “H” wide flange beams. JET HDT Series Trolleys comply with OSHA regulations, ANSI/ASME B30.11 and B30.17 standards. IMPORTANT SAFETY INSTRUCTIONS To reduce risk of injury: 1. Beam must be properly installed and rated for anticipated loads. 2. Do not install trolley on beams of unknown capacity. 3. Do not install trolley on damaged or deformed beams. 4.
PAGE 2
HDT Series Trolley: Specifications Capacity (Ton) Stock No. 1/2 Ton 262005 1 Ton 262010 2 Ton 262020 3 Ton 262030 5 Ton 262050 Beam Flange Width G (min-max) Min. Radius Curve mm 63–203 900 in. 2-1/2–8 35 mm 76–203 1000 A B C (Ø) 5 (kg) 188 300 53 11 (lb) 7-3/8 11-13/16 2-13/16 7.7 (kg) 212 318 63 130 Net Weight D E (Ø) F H 117 4-5/8 75 90 101 31.8 3 3-9/16 4 1-1/4 15/16 1-3/8 85 100 118 43 30.5 34.25 in.
PAGE 3
HDT Series Trolley: Parts Breakdown Index Part No.
PAGE 4
Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.