Operating Instructions and Parts Manual 3/4, 1-1/2, and 3 Ton Grip Pullers Models JG-75A, JG-150A, JG-300A Model JG-75A shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. JET products carry a limited warranty which varies in duration based upon the product.
Table of Contents Warranty and Service.................................................................................................................................... 2 Warning ......................................................................................................................................................... 3 Introduction ...................................................................................................................................................
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for a JET Grip Puller. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This tool has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or JET.
Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Grip Puller is assembled and operating properly. Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions.
4. Pull the wire rope through by hand to take up the slack and make sure that the exit point is not obstructed. 5. While keeping the wire rope taut, push down on the clamp lever and allow it to spring back to its natural position. This will engage the wire rope within the puller. 6. Mount the telescopic handle to either the forward or reverse lever, according to the action desired. Rotate the handle until it is secure on the lever. 7. The puller is now ready to operate.
Make sure hooks are not deformed and that the puller body has not been warped or damaged. Before storing the grip puller: 5. After use, remove the wire rope from the main body by setting the clamp lever into the notch (disengage clamp), then pulling the wire rope from the inlet side at the rear of the puller. Use care to prevent the wire rope from kinking. If the rope is left shaped like a basket or is kinked many turns at a single point, its strength is greatly diminished and may result in failure.
JG-75A (3/4 Ton Grip Puller) 8
Parts List: JG-75A (3/4 Ton Grip Puller) Index No. Part No. Description Size Qty 1 ............... JG75A-1 ................... Case, Right .......................................................... .................................... 1 2 ............... TS-2285121 ............. Flat Head Screw .................................................. M5x12 ......................... 1 3 ............... JG75A-3 ................... Washer ................................................................. ........
JG-150A (1-1/2 Ton Grip Puller) 10
Parts List: JG-150A (1-1/2 Ton Grip Puller) Index No. Part No. Description Size Qty 1 ............... JG150A-1 ................. Case, Right .......................................................... .................................... 1 2 ............... TS-2285121 ............. Flat Head Screw .................................................. M5x12 ......................... 1 3 ............... JG75A-3 ................... Washer ................................................................. ......
JG-300A (3 Ton Grip Puller) 12
Parts List: JG-300A (3 Ton Grip Puller) Index No. Part No. Description Size Qty 1 ............... JG300A-1 ................. Case, Right .......................................................... .................................... 1 2 ............... JG300A-2 ................. Flat Head Screw .................................................. M5x8 ........................... 1 3 ............... JG75A-3 ................... Washer ................................................................. .......
This page intentionally left blank.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
