This .pdf document is bookmarked Operating Instructions and Parts Manual 17-inch Drill Press Model JDP-17MF WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com Part No. M-354169 Revision C3 09/2013 Copyright © 2013 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools.
Table of Contents Warranty and Service ............................................................................................................................................ 2 Table of Contents .................................................................................................................................................. 3 Warning ...........................................................................................................................................................
Warning Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. Support workpiece adequately at all times during operation; maintain control of work at all times. This drill press is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a drill press, do not use until proper training and knowledge have been obtained.
• USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS.
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This JET drill press is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug (A), supplied with the drill press, must be replaced with a UL/CSA listed plug suitable for 230V operation (D).
On-Off Switch Padlock To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock (not included) is highly recommended. To lock out an on-off switch: 1. Open the padlock. See Fig. A. 2. Insert through holes in the start button. See Fig. B 3. Close the padlock. 4. Put the key in a safe place.
Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a JET Model JDP-17MF Drill Press. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual.
Unpacking Contents of the Shipping Container 1 1 1 1 1 1 1 3 1 1 4 1 1 Head Assembly Table Column and Bracket Assembly Base Owner’s Manual Warranty Registration Card Chuck and Chuck Key Downfeed Handle Table Bracket Lock Handle Table Bracket Raising Handle M10 x 40 Hex Cap Bolts Arbor Drift Key Tools Supplied for Assembly 1 1 3mm Hex Wrench 5mm Hex Wrench Tools Required for Assembly (not included) 1 1 17mm Box Wrench or a 6”-8” Adjustable Wrench Rubber mallet (or hammer with wood block) Read and und
Assembly 1. Place the base (A, Figure 1) on a level floor. 2. With a 17mm wrench attach the column assembly (B, Figure 1) to the base (A, Figure 1) with four M10 x 40 hex cap bolts (C, Figure 1). Tighten firmly. 3. Thread lock handle (D, Figure 2) into the table bracket (E, Figure 2). Figure 1 4. Loosen the set screw (F, Figure 3) on the raising handle (G, Figure 3) with a 3mm hex wrench. 5. Slide the handle onto the table bracket shaft. 6.
. Install three down feed handles (B, Figure 4) into the down feed hub (C, Figure 4). 13. Thoroughly clean spindle, arbor and chuck (A/B/C, Figure 5). Important: These three pieces must be free of any rust protectant, or lubricant. If they are not clean, the arbor and chuck will fail to seat in the spindle. 14. Turn the arbor until the tang on the arbor engages the slot at the end of the spindle. Slide arbor up into spindle. 15. Firmly push chuck by hand onto taper of arbor. Figure 4 16.
Adjusting the Depth Stop To drill multiple holes at the same preset depth, use the depth stop: 1. Use a pencil to mark the depth the bit will drill into the workpiece (A, Figure 7). 2. With the drill bit in the chuck, lower down feed handle to advance bit to your mark,see Figure 7. 3. With your other hand, advance the lock nuts (B, Figure 7) on the depth stop rod until they are snug to the seat (C, Figure 7). 4. The drill bit will now advance to this point. 5.
Return Spring Adjustment The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary: 1. Unplug the machine from the power source. 2. Loosen two jam nuts (A, Figure 9). Do not remove. 3. Firmly hold the coil spring cover (B, Figure 9). 4. Pull out the cover and rotate until the pin (C, Figure 9) on the return spring plate engages the next notch in the coil spring cover.
Basic Operation • Always use a back-up piece of scrap wood to cover the table. This protects both the table and the drill bit. • Place material to be drilled in such as way as to come into contact with the left side of the column. This prevents the material from spinning. If the workpiece is not large enough to come into contact with the column, use a clamp or drill press vise that is securely fastened to the table. Failure to comply may cause serious injury.
Troubleshooting Trouble Drill press will not start. Drill press does not come up to speed. Drill Press vibrates excessively. Probable Cause Remedy Drill press unplugged from wall, or motor. Check all plug connections. Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker. Cord damaged. Replace cord. Starting capacitor bad. Replace starting capacitor. Extension cord too light or too long. Replace with adequate size and length cord. Low current.
Trouble Probable Cause Remedy Bent drill bit Replace drill bit. Worn spindle bearings. Replace spindle bearings. Bit, or chuck not properly installed. Reinstall the bit, or chuck properly. Quill returns too slowly, or too fast. Spring has improper tension. Adjust return spring tension Chuck, or arbor do not stay in place. Dirt, grease, etc. on arbor, chuck or spindle. Clean all mating surfaces thoroughly with a cleaner degreaser. Excessive drill bit runout or wobble.
JDP-17MF Drill Press Assembly 18
Parts List Index No. Part No. Description Size Qty 1 ................ 10600111 .................. Base......................................................................... ...................................... 1 2A .............. 12909001A1 .............. Column and Holder Assembly ................................. ...................................... 1 3 ................ TS-1525021 .............. Set Screw ................................................................ M10x12 ..................
Index No. Part No. Description Size Qty 68 .............. 10706802 .................. Retaining Ring ......................................................... ...................................... 2 69 .............. 10606904 .................. Pulley Set Nut .......................................................... ...................................... 1 70 .............. 10607018 .................. Spindle Pulley .......................................................... ...........................
Index No. Part No. Description Size Qty 701 ............ TS-152706 ................ Hex Wrench ............................................................. 5MM .............................. 1 801 ............ 28065558U4.............. Bulb Wire ................................................................. ...................................... 2 903 ............ 2801ABRF04............. Strain Relief ............................................................. ......................................
Electrical Connections JDP-17MF ELECTRICAL SCHEMATIC - 115V STARTING CAPACITOR 200MFD 125 VAC ON / OFF SWITCH BLACK 3 BLACK WHITE WHITE 2 1 4 GREEN GREEN GREEN BLACK WHITE GROUND LAMP SWITCH BLACK BLACK WHITE BLACK LAMP JDP-17MF ELECTRICAL SCHEMATIC - 230V STARTING CAPACITOR 200MFD 125 VAC ON / OFF SWITCH BLACK 3 BLACK WHITE WHITE 2 1 4 GREEN GREEN LAMP SWITCH BLACK BLACK WHITE BLACK LAMP 22 GREEN BLACK WHITE GROUND
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com www.waltermeier.
