Use and Care Manual

5
5.0 Specifications
Model number ........................................................................... IDP-17 ........................................................ IDP-22
Stock number ............................................................................354300 ........................................................ 354301
Motor and electricals:
Motor type…………………………………………………….totally enclosed fan cooled, induction, capacitor start.........
Horsepower .............................................................................. 1 HP ...................................................... 1-1/2 HP
Phase ...................................................................................... single .......................................................... single
Voltage ..................................................... 115/230V (prewired 115V) ........................... 115/230V (prewired 115V)
Cycle ........................................................................................ 60Hz ........................................................... 60Hz
Listed FLA (full load amps) ...................................................... 17.2 A ......................................................... 12.4 A
Starting amps ............................................................................ 9.0 A .......................................................... 7.4 A
Running amps (no load) ............................................................ 8.9 A .......................................................... 7.6 A
Start capacitor ....................................................... 300 MFD 125VAC ....................................... 400 MFD 125VAC
Run capacitor .............................................................. 30μF 250VAC .............................................. 40μF 250VAC
Power transfer ...........................................................................v-belt ........................................................... v-belt
On/off switch ................................................................... push button ................................................. push button
Motor speed ...................................................................... 1720 RPM ................................................... 1720 RPM
Main power cord ............................... 18 AWG, 6 ft. (183 cm) with plug ................... 14AWG, 6 ft. (183 cm) with plug
Work lamp power cord ...................... 18 AWG, 6 ft. (183 cm) with plug .................. 18 AWG, 6 ft. (183 cm) with plug
Recommended circuit size
1
......................................................... 20A ............................................................. 20A
Sound emission........................................ 70 dB at 40 in. without load .......................... 70 dB at 40 in. without load
Work lamp...................................................................... 110V to 12V ................................................ 110V to 12V
Head and Capacities:
Swing
2
............................................................... 16-7/8 in. (430 mm) ..................................... 21-7/8 in. (560 mm)
Chuck style and shank capacity ........................... keyed, 5/8” (16mm) ......................................keyed, 5/8” (16mm)
Chuck arbor taper............................................................JT-3 to MT2 ................................................. JT-3 to MT3
Spindle taper .............................................................................. MT2 ............................................................ MT3
Spindle travel, maximum........................................ 3-5/16 in. (85 mm) ................................... 4-13/16 in. (122 mm)
Spindle travel per one revolution of handle ..................... 3 in. (78 mm) ....................................... 4-1/2 in. (115 mm)
Quill diameter ........................................................ 2-1/16 in. (52 mm) ......................................... 2-5/8 in. (62 mm)
Number of spindle speeds ............................................................. 12 ............................................................... 12
Maximum no-load speed range ............................... 350 to 2800 RPM .........................................175 to 3050 RPM
Maximum spindle to table distance....................... 30-1/2 in. (775 mm) ........................................... 28 in. (710 mm)
Maximum spindle to base distance........................... 50 in. (1270 mm) ................................... 48-1/2 in. (1230 mm)
Maximum chuck to table distance .............................. 27 in. (686 mm) ..................................... 24-1/2 in. (622 mm)
Maximum chuck to base distance ...................... 46-1/2 in. (1181 mm) ........................................... 39 in. (990 mm)
Drilling capacity, cast iron ........................................... 3/4 in. (20 mm) ......................................... 1-1/4 in. (32 mm)
Drilling capacity, mild steel .......................................... 5/8 in. (16 mm) ............................................... 1 in. (25 mm)
Work lamp................................................................. LED, adjustable ........................................... LED, adjustable
Materials:
Head .................................................................................... cast iron ...................................................... cast iron
Table ........................................................... surface-ground cast iron .............................. surface-ground cast iron
Column ...................................................................................... steel ............................................................ steel
Base .................................................................................... cast iron ...................................................... cast iron
Table:
Table size ................................................ 14 x 14 in. (355 x 355 mm) ............... 18-5/8 x 16-1/8 in. (473 x 410 mm)
Table slots, number of ..................................................................... 2 ................................................................. 3
Table slots, general size (WxD) .................. 1/2 x 1 in. (13 x 25.4 mm) ............................ 5/8 x 1 in. (16 x 25.4 mm)
T-slot dimensions (WxD)............................. 3/4 x 3/8 in. (19 x 9.5mm) ........................... 1 x 3/8 in. (25.4 x 9.5 mm)
Distance between slots (centers) ............................. 3-7/8 in. (98 mm) ......................................... 3-1/2 in. (91 mm)
Table tilt .................................................................... 45 deg. L and R ........................................... 45 deg. L and R
Table rotation around column ............................................... 360 deg. ...................................................... 360 deg.
Table elevating system ....................................... worm gear with rack ..................................... worm gear with rack
Recommended maximum weight on table .................... 110 lb. (50 kg) ............................................. 176 lb. (80 kg)
1
Subject to local and national electrical codes
2
Swing is twice the distance from column to spindle center (i.e., the maximum diameter of workpiece that can be
drilled to its center).