Pneumatic Ratchet Wrench #505322, JAT-322 #505323, JAT-323 Operation & Parts Manual M-505322 Edition 2 06/2015 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
Safety warnings General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
20. Do not use power tools in damp or wet location, or expose them to rain. Keep work area well lighted. 21. Do not leave a connected tool unattended. When not in use, disconnect tool from air source. 22. Shut off air supply and discharge any residual pressure from tool before removing hose, making adjustments, changing accessories, or storing tool. 23. Make sure tool is switched off, and your finger off the trigger, before connecting to air supply. 24.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-322 and JAT-323 Pneumatic Ratchet Wrench. This manual contains instructions on safety precautions, general operating procedures, maintenance procedures and parts breakdown. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Tool specifications Model number JAT-322 JAT-323 Stock number 505322 505323 Square drive 3/8 in. 1/2 in. Bolt capacity 1/2 in. 1/2 in. Anvil retainer type Ball detent Ball detent Impact mechanism Single hammer Single hammer Maximum torque 100 lbf•ft (135.58 N•m) 100 lbf•ft (135.58 N•m) Working torque 25-70 lbf•ft (33.9-94.91 N•m) 25-70 lbf•ft (33.9-94.91 N•m) Free speed 600 RPM 600 RPM Average air consumption 4 CFM 4 CFM Air inlet 1/4 in. NPT 1/4 in.
(toward High), counterclockwise to decrease (toward Low). Setup and Assembly Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. Box contents: 1 1 1 5. Turn direction knob to forward (F) or reverse (R) rotation. Make sure nut or bolt can withstand rated torque of ratchet wrench.
Maintenance Excess air pressure and/or unclean air will shorten the tool’s life and may create a hazardous situation. Lubrication The ratchet wrench should be lubricated daily (or before each use) with air tool oil through the air inlet. During continual operation, it should be reoiled every 1 to 2 hours. This can be done with an in-line oiler, or manually. If done manually, proceed as follows: 1. Disconnect air hose from tool. 2. Place 4 or 5 drops of air tool oil into air inlet.
Air System Recommendations Lubrication Equip the air compressor intake with a replaceable air filter that can be easily cleaned. Use a light oil containing rust inhibitors, such as SAE #10. Many JET air tools have integral oil reservoirs, which should be kept filled when in-line oilers are not used. Use safety shut-off valves so air flow can be stopped quickly in case of a line break. When using multiple hoses, air hoses should be larger than leader hose.
Troubleshooting JAT-322/323 Ratchet Wrenches Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed. Open valve; clear any obstructions. Dirt or gum deposits on components. Flush tool with gum solvent. If problem persists, disassemble, clean and lubricate internal parts. Rotor vanes or other components are worn.
Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately.
#505322, JAT-322, 3/8-inch Ratchet Wrench – exploded view 9 5 8 5 3 3 7 3 4 7 2 0 7 6 2 4 5 3 8 6 9 6 6 3 4 3 6 2 4 2 7 6 8 3 9 3 6 6 0 4 1 4 0 3 5 2 7 2 9 0 5 5 5 2 4 0 8 4 9 4 3 0 2 3 0 5 1 1 7 6 5 2 4 5 5 0 1 3 4 4 3 2 9 2 8 2 3 4 6 5 2 0 1 0 1 2 5 5 4 2 3 1 1 1 5 4 3 5 1 1 6 0 0 1 56 11 7 0 8 0 JAT-322,323 Ratchet Wrenches 12
#505322, JAT-322, 3/8-inch Ratchet Wrench – parts list Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part No.
#505323, JAT-323, 1/2-inch Ratchet Wrench – exploded view 9 5 3 3 7 3 4 7 2 0 8 7 6 2 5 4 5 3 8 6 9 6 6 3 4 3 6 2 4 2 7 6 8 3 9 3 6 6 0 4 1 4 0 3 5 2 7 2 5 0 9 0 4 5 5 2 5 5 5 2 4 0 8 4 9 4 3 0 2 3 0 5 1 1 7 6 1 3 4 4 3 2 9 2 8 2 3 4 6 5 2 0 1 5 1 0 2 5 4 2 3 1 1 1 5 4 3 5 1 1 6 0 0 1 56 11 7 0 8 0 JAT-322,323 Ratchet Wrenches 14
#505323, JAT-323, 1/2-inch Ratchet Wrench – parts list Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part No.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.