Pneumatic Micro Die Grinder #505410, JAT-410 Operation Manual M-505410 Edition 1 05/2019 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
IMPORTANT SAFETY INSTRUCTIONS General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
24. Keep visitors a safe distance from the work area. Keep children away. 25. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 26. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 27. Repetitive motions and/or exposure to constant vibration can be harmful to hands and arms.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-410 Pneumatic Micro Die Grinder. This manual contains instructions on safety precautions, and general operating and maintenance procedures. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Tool specifications Model JAT-410, Straight Micro Die Grinder Stock number 505410 Collet size 1/8 in. Horsepower 0.1 Free speed 70,000 RPM Air consumption under load 5.5 SCFM Air inlet 1/4 in. NPT Air hose inside diameter 3/8 in. Required air pressure 90 psi (621 kPa) Vibration value 1.10 m/s2 Sound power 1 86.0 dB(A) Sound pressure 1 81 dB(A) Speed setting variable Grip Pencil style shaft Hose included 5-ft. with strain relief sleeve Overall Length 5.36 in. (136.
Setup and Assembly 5. Make sure grinder is off (air regulator turned all the way counterclockwise). Turn on air. Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. 6. Hold die grinder firmly and rotate air regulator clockwise to turn on and adjust speed. A directional graphic is printed next to the regulator. 7.
Air system requirements 1. Use proper air hose size (refer to tool specifications). The hose should be just long enough to serve the working area. Excessive hose length will cause pressure drop. 1. Make sure the air compressor supplies clean, dry air at correct CFM for the tool. 2. Set air pressure to 90 psi. Excess air pressure and/or unclean air will shorten the tool’s life and may create a hazardous situation. 3.
Figure 2 Recommended arrangement of air piping and air line system 8 JAT-410 Micro Die Grinder
Troubleshooting JET® Air Tools Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Tool will not start. Possible cause Remedy Air valve closed or obstructed. Open valve; clear any obstructions. Dirt or gum deposits on components. Flush tool with gum solvent. If problem persists, disassemble, clean and lubricate internal parts. Rotor vanes or other components are worn.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. JET products carry a limited warranty which varies in duration based upon the product.
JET 11
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.