Pneumatic 7in. Angle Polisher #505741, JAT-741 Operation & Parts Manual M-505741 Edition 2 06/2015 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
Safety warnings General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
20. Do not use power tools in damp or wet location, or expose them to rain. Keep work area well lighted. 21. Do not leave a connected tool unattended. When not in use, disconnect tool from air source. 22. Shut off air supply and discharge any residual pressure from tool before removing hose, making adjustments, changing accessories, or storing tool. 23. Make sure tool is switched off, and your finger off the trigger, before connecting to air supply. 24.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-741 Pneumatic Angle Polisher. This manual contains instructions on safety precautions, general operating procedures, maintenance procedures and parts breakdown. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Tool specifications Model number JAT-741 Stock number 505741 Pad size 7 in. round Head angle 90 deg. Horsepower 0.75 Spindle thread 5/8”-11 UNC Free speed 2500 RPM Average air consumption 4.2 CFM Air inlet 1/4 in. NPT Air hose inside diameter 3/8 in. Required air pressure 90 psi (621 kPa) Vibration value <2.5 m/s2 Noise level 1 90 dB(A) Power setting Variable speed Grip Inline Overall Length 12 in. (304.8 mm) Housing material Aluminum with rubber grip Net weight 4.74 lb.
or 5 drops of air tool oil (not included) into the air inlet. Setup and Assembly Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. 7. IMPORTANT: Connecting a quick-change coupling directly to the tool is not recommended, as vibration may cause the connection to fail.
4. When finished operating polisher, disconnect air hose. Wipe off housing with a dry cloth. Place 4 or 5 drops of air tool oil into air inlet; re-connect air and run tool for a few seconds to distribute the oil. Disconnect air. Periodically apply 1 or 2 drops of air tool oil to throttle lever pivot, and work lever to distribute the oil. Storage Avoid storing this tool in very humid locations which promotes rusting of internal mechanisms. Always oil the tool and disconnect air hose before storage.
Recycling Protect the environment. Your tool contains materials which can be recovered or recycled. When its useful life has expired, please leave tool at a specialized facility.
Troubleshooting JAT-741 Angle Polisher Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed. Open valve; clear any obstructions. Dirt or gum deposits on components. Flush tool with gum solvent. If problem persists, disassemble, clean and lubricate internal parts. Rotor vanes or other components are worn.
Replacement parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately.
#505741, JAT-741, 7in.
#505741, JAT-741, 7in. Angle Polisher – parts list Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Part No.
This page intentionally left blank.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.