Pneumatic Metal Shear #505910, JAT-910 Operation & Parts Manual M-505910 Edition 2 06/2015 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
Safety warnings General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
20. Do not use power tools in damp or wet location, or expose them to rain. Keep work area well lighted. 21. Do not leave a connected tool unattended. When not in use, disconnect tool from air source. 22. Shut off air supply and discharge any residual pressure from tool before removing hose, making adjustments, changing accessories, or storing tool. 23. Make sure tool is switched off, and your finger off the trigger, before connecting to air supply. 24.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-910 Pneumatic Metal Shear. This manual contains instructions on safety precautions, general operating procedures, maintenance procedures and parts breakdown. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Tool specifications Model number JAT-910 Stock number 505910 Metal capacity 18 gauge (0.048 in.) Cutting head swivel 360 deg. Free speed 2800 RPM Average air consumption 4 CFM Air inlet 1/4 in. NPT Air hose inside diameter 3/8 in. Required air pressure 90 psi (621 kPa) Vibration value 4.2 m/s2 Noise level 1 Power setting 82 dB(A) Variable speed trigger Grip Pistol style Overall Length 9-1/16 in. (4.11 mm) Housing material Aluminum Net weight 2.73 lb. (1.
Setup and Assembly 4. Press trigger to operate. Speed is regulated by pressure applied to trigger. Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. 5. Use moderate pressure against workpiece; do not force tool. 6. Release trigger to stop tool.
Air system requirements 1. Use proper air hose size (refer to tool specifications). The hose should be just long enough to serve the working area. Excessive hose length will cause pressure drop. 2. Make sure air compressor supplies clean, dry air at correct CFM for the tool. 3. Set air pressure to 90 psi. Excess air pressure and/or unclean air will shorten the tool’s life and may create a hazardous situation. 4. Drain water from air compressor tank daily, as well as any condensation from air lines.
Figure 2 Recommended arrangement of air piping and air line system JET 9
Troubleshooting JAT-910 Pneumatic Shear Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed. Open valve; clear any obstructions. Dirt or gum deposits on components. Flush tool with gum solvent. If problem persists, disassemble, clean and lubricate internal parts. Rotor vanes or other components are worn.
Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately.
#505910, JAT-910, Pneumatic Shear – exploded view 12 JAT-910 Pneumatic Shear
#505910, JAT-910, Pneumatic Shear – parts list Index 1 2 3 4 5 6 7 8 9 10 11 13 14 15 Part No. JAT910-01 73402 70103 70104 JAT910-05 JAT910-06 70107 70108 70109NPN JAT620-11 SM-30111 BB-626ZZ JAT910-14 JAT910-15 Description Motor housing Spring pin 2.5x22pL Air inlet Trigger Valve stem Valve bushing O-Ring 4.8x1.9 Valve spring O-Ring 9.8x1.9 Exhaust diffuser Cap Ball bearing 626ZZ Rear end plate Rotor Qty 1 1 1 1 1 1 1 1 2 1 1 2 1 1 Index 16 17 18 19 20 21 22 23 24 26 28 29 30 33 Part No.
This page intentionally left blank.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
