Use and Care Manual

6
4.0 Specifications
Table 1
Stock number
578842 577842 578634 577634
Model number IBDG-248 IBDG-248VS IBDG-436 IBDG-436VS
Motor and Electricals
Motor
Type
totally enclosed,
induction,
capacitor start
totally enclosed,
induction,
with inverter
totally enclosed,
induction,
capacitor start
totally enclosed,
induction,
with inverter
Horsepower 1HP
Phase 1 PH 3 PH 1 PH 3 PH
Voltage 115/230V, prewired 115V
Cycle 60 Hz
Listed FLA (full load amps) 11 / 5.5 A 7 / 3.5 A 11 / 5.5 A 7 / 3.5 A
Speed 3,600 RPM 900-3600 RPM 3,600 RPM 900-3600 RPM
Starting capacitor
200MFD,
125VAC
n/a
200MFD,
125VAC
n/a
Running capacitor 35µF, 250V n/a 35µF, 250V n/a
Input power required Single phase 115V (or 230V if rewired)
On/off switch toggle TACT toggle TACT
Power transfer Direct drive
Power cord SJT 16AWG x 3C, 6 ft. (183cm)
Power plug installed 5-15P, 125V/15A
Recommended minimum circuit size
1
15 A
Sound emission without load
2
75 dB at 3 ft. (92cm)
Disc sander
Disc diameter 9 in. (228.6m)
Sanding disc 80 Grit, Aluminum Oxide
Disc table size 11-13/16 x 5-29/32 in. (300 x 150 mm)
T-slot size (W x D) 3/4 x 3/8 in. (19 x 9.6 mm)
Disc table tilt 45 deg. down
Dust port diameter 2 in. (52mm)
Base
Foot print (W x D) 9-1/2 x 8-1/16 in. (240 x 205mm)
Mounting holes diameter 7/16 in. (11mm)
Distance between mounting hole
centers
8-15/32 in. (215mm)
Belt sander
Sanding belt size (L x W) 48 x 2 in. (1219 x 52) 36 x 4 in. (914 x 102 mm)
Sanding belt type 80 Grit, Aluminum Oxide
Belt speed (SFPM) 4,712 1,178 – 4,712 3,769 942-3,769
Belt table tilt 45 deg. down
Belt table size (L x W) 4-11/32 x 2-15/16 in. (110 x 75 mm) 6-5/16 x 2-15/16 in. (160 x 75 mm)
Tool rest tilt 45 deg. down
Tool rest size (L x W) 3-1/8 x 2-5/8 in. (79 x 67 mm) 5-1/8 x 3-1/8 in. (130 x 80 mm)
Drive wheel size (Dia. x W) 5 x 2-1/16 in. (127.5 x 53 mm) 4 x 4-1/16 (102.5 x 104 mm)
Dust port diameter 2 in. (52 mm)
Minimum dust extraction required
Weights
Net weight 74 lbs. (33.82 kg) 73 lbs. (33.32 kg)
Shipping weight 97 lbs. (44.25 kg) 92 lbs. (41.96 kg)