Operating Instructions and Parts Manual Dust Collector Models: DC-650BK, DC-650CK, DC-650MK DC-650BK shown WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com DC-650CK shown Part No. M-708642 Revision C 06/2010 Copyright © 2010 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET ® tools.
Table of Contents Warranty and Service .................................................................................................................................2 Table of Contents ......................................................................................................................................3 Warnings ...................................................................................................................................................4 Introduction .................
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector. 23.
Specifications Base Machine with 30 micron Filter Bag Kit ............................................................................ 708642BK Base Machine with 5 micron Filter Bag Kit ............................................................................. 708642MK Base Machine with Canister Kit..............................................................................................708642CK Base Machine (All Models): Model .........................................................................
Shipping Contents (cont) Unpacking The table below lists the shipping cartons that are included with the models of the DC-650 Dust Collector. Base Unit 1. Locate your particular model and verify that you have received the all the correct cartons.
Base Unit Assembly The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! Motor Housing and Support Cylinder Referring to Figure 1: 1. Place the impeller housing (H) on the floor with the motor (G) facing upwards as shown. 2. Attach the fan (B) with the blades facing up to the motor shaft (A). Allow a 1/16"-1/8" clearance between the fan (B) and housing (F). 3.
Filter Bag Kit Assembly If you purchased Model DC-650BK or DC-650MK Dust Collector, this section describes the assembly and installation of the contents of the Filter Bag Kit (SN 708642B and 708642MF). Filter Bag Installation Referring to Figure 4: 1. Thread an M6 hex nut onto the filter rod (B), followed by an M6 flat washer washer (A). Thread the support rod motor/fan housing and tighten nut housing using a 10 wrench. bag support and M6 lock (B) into the against the 2.
Canister Kit Assembly If you purchased Model DC-650CK Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708737C). Canister Filter Installation Referring to Figure 6: 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A). 2. Mount handle (B) to the arm (C) with an M8 flat washer (D), M8 lock washer (E) and M8 hex nut (F). 3.
Dust Collector RF Remote Power Control (Optional) Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in serious injury! The DC-RC Remote Power Control (Figure 10) should be used for activating Dust Collection units powered by 115V only up to 1-1/2HP. The DC-RC Remote Power Control unit is rated at 115V, Single Phase only.
Changing Operating Frequency Installing the DC-RC Remote Power Control If several devices are controlled by the same type remote control unit, each remote control unit can be set to operate at its own unique operating frequency as follows: The optional DC-RC Remote Power Control unit can be placed anywhere for convenience and portability if used to control other machines or it can be mounted as a permanent part of the DC-650 Dust Collector. Referring to Figure 11: 1.
Cleaning the Filter – DC-650CK Maintenance Clean both the filter and collector bag frequently to keep the collector's performance at its optimum. Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! To clean the filter turn the handle a couple rotations so the dust falls into the collector bag.
Parts Replacement Parts Replacement parts are listed in the Parts List on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts List – Base Machine Index No. Part No. Description Size Qty 1 .............. 422109W ................Impeller Housing......
Parts Breakdown – Base Machine 15
Canister Filter Assembly Index No. Part No. Description Size Qty 1 .............. 708737....................Canister Filter ................................................................................................ 1 2 .............. 331037....................JET Knob .........................................................M6x20.................................... 4 3 .............. 331047....................Pad......................................................................................
30 Micron Filter Bag Assembly Index No. Part No. Description Size Qty 1 .............. 708695....................Filter Bag ........................................................30 Micron ............................... 1 2 .............. AB422028 ...............Retainer Strap ............................................................................................... 1 3 .............. 708697A .................Collector Bag...........................................................................
5 Micron Filter Bag Assembly Index No. Part No. Description Size Qty 1 .............. 708701....................Filter Bag ........................................................5 Micron ................................. 1 2 .............. AB422028 ...............Retainer Strap ............................................................................................... 1 3 .............. 709565....................Clear Plastic Collection Bag (Package of 5) ...........................................
Wiring Diagrams for DC-650 19
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.waltermeier.