Operating Instructions and Parts Manual DC-1100VX Series Dust Collectors Now with DC-1100VX with Bag Filter Kit WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com DC-1100VX with Canister Kit Part No. M-708657 Revision A 03/2011 Copyright © 2011 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET ® tools.
Table of Contents Warranty and Service .................................................................................................................................2 Table of Contents ......................................................................................................................................3 Warnings ...................................................................................................................................................4 Introduction .................
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector. 23.
Specifications DC-1100VX-BK (Base Machine with 30 Micron Filter Bag Kit) .........................................................708657K DC-1100VX-5M (Base Machine with 5 Micron Filter Bag Kit) ..........................................................708658K DC-1100VX-CK (Base Machine with Canister Filter Kit)..................................................................708659K Base Machine (All Models) Model .............................................................................................
Unpacking Shipping Content The table below lists the shipping cartons that are included with the models of the DC-1100VX Dust Collector. Base Unit (SN 708657) 1 – Housing (A) 2 – Hose Clamps (B) 1 – Hose (C) 1 – Impeller (Motor/Fan Assembly) (D) 1 – Inlet Port (E) 1 – Impeller Cover (F) 3 – Support Legs (G) 1 – Base (H) 4 – Casters (J) 1 – Cone (K) 1 – Support Bracket (L) 1 – Owner's Manual (not shown) 1 – Warranty Card (not shown) 1 – Hardware Bag, Base Unit (SN DC1100-HP) 1 – Hardware Bag, Cone Assly.
Canister Filter Kit 30-Micron Bag Filter Kit (SN 708639B) (SN 708636F) 1 – Handle (O) 1 – Canister Filter (P) 1 – Snap Ring (Q) 5 – Collector Bags (R) 1 – Canister Filter Hardware Bag (SN DC1100-CHP) Contains: (2) M10 Hex Nuts (S) (2) M10 Flat Washers (T) (1) M10 Lock Washer (U) (4) Knobs (V) 1 – Upper Bag Hanger (Y) 1 – Hanger Bracket (Z) 1 – Collector Bag (X) 1 – Filter Bag (W) 1 – Retainer Strap (AA) Filter Bag Kit Contents 5-Micron Bag Filter Kit (SN 708636MF) 1 – Upper Bag Hanger (BB) 1 – Hange
Base Unit Assembly Base 1. Install four casters to the underside of the base as pictured in Fig. 2. Referring to Figure 1: 2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B) against the base with a 14mm wrench. This will give the caster proper clearance. Figure 1 Motor and Fan Assembly Referring to Figure 2: 3.
6. Install the housing (A, Fig. 5) to two support legs (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. Note: For filter bag models only – Before attaching third support bracket place the hanger bracket (D, Fig.5) between the support bracket and the housing. This action is not necessary for canister filter units. 7. Tighten all nuts and bolts at this time with a 13mm wrench.
Filter Bag Kit Assembly If you purchased a DC-1100VX-BK, or DC-1100VX5M Dust Collector, this section describes the assembly and installation of the contents of the Filter Bag Kit (SN 708636F or 708636MF). Filter Bag Installation Referring to Figure 8: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Feed the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F).
Canister Kit Assembly If you purchased Model DC-1100VX-CK Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708639B). Canister Filter 1. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 10). 2. Mount the canister filter on top of the collector housing (A, Fig. 5) and tighten the knobs on the canister filter (Figure 10). Figure 10 Collector Bag 3.
Dust Collector RF Remote Power Control (Optional) Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in serious injury! The DC-RC Remote Power Control (Figure 14) should be used for activating Dust Collection units powered by 115V only up to 1-1/2HP. The DC-RC Remote Power Control unit is rated at 115V, Single Phase only.
Changing Operating Frequency Installing the DC-RC Remote Power Control (Optional Accessory) If several devices are controlled by the same type remote control unit, each remote control unit can be set to operate at its’ own unique operating frequency as follows: The DC-RC Remote Power Control unit can be placed anywhere for convenience and portability if used to control other machines or it can be mounted as a permanent part of a machine, such as the DC1100VX Dust Collector. Referring to Figure 15: 1.
Cleaning the Filter: DC-1100VX-CK Maintenance Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Clean both the canister filter and collector bags frequently to keep the collector's performance at its optimum.
Parts Parts Breakdown – DC-1100VX Dust Collectors 16
Parts List – DC-1100VX Dust Collectors Ordering Replacement Parts To order parts or reach our service department, call 800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Index No. Part No. Description Size Qty 1 .............. 411035W ................Impeller Housing................................................................
Index No. Part No. Description Size Qty ................ DC1200-53 ..............Grounding Label (not shown)........................................................................... 1 ................ DC1200-54 ..............Direction Label (not shown) ............................................................................. 1 ................ DC1100VX-ID..........I.D. Label (not shown) ..................................................................................... 1 ................
Canister Filter Kit (708639B) Index No. Part No. Description Size Qty ................ 708639B .................Canister Filter Kit (index # 1-24)......................................................................... 1 .............. 331050....................Handle ........................................................................................................... 1 2 .............. TS-1540071 ............Hex Nut............................................................M10 .....................
30-Micron Filter Bag Kit (708636F) Index No. Part No. Description Size Qty ................ 708636F..................30-Micron Filter and Collection Bag Kit (index # 1-5) ........................................... 1 .............. 708698....................Filter Bag ........................................................30 Micron ............................... 1 2 .............. AB410012 ...............Retainer Strap ...................................................................................
5-Micron Filter Bag Kit (708636F) Index No. Part No. Description Size Qty ................ 708636MF ...............5-Micron Filter and Collection Bag Kit (index # 1-6) ............................................. 1 .............. 708706....................Filter Bag ........................................................5 Micron ................................. 1 2 .............. AB410012 ...............Retainer Strap ...................................................................................
Wiring Diagram – DC-1100VX Dust Collectors 22
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.waltermeier.