This .pdf document is bookmarked Operating Instructions and Parts Manual XACTA® Saw Deluxe WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com Part No. M-708674 Revision D 09/2013 Copyright © 2013 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools.
Table of Contents Warranty and Service .............................................................................................................................. 2 Table of Contents .................................................................................................................................... 3 Warnings ................................................................................................................................................. 4 Introduction .....................
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This table saw is designed and intended for use by properly trained and experienced personnel only.
19. Keep visitors a safe distance from the work area. Keep children away. 20. Make your workshop child proof with padlocks, master switches or by removing safety keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation.
Introduction The JET XACTA® Saw Deluxe table saw you have purchased is a high quality machine tool that will give you years of superior service. You will get maximum performance and enjoyment from your new table saw if you will take a few moments now to review the entire manual before beginning assembly and operation. This table saw, as well as all JET products, are backed by a nationwide network of authorized distributors and/or service centers.
Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury. Shipping Contents Unpacking Remove box and wood crating completely from around saw. Check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Table Saw is assembled and running properly.
Contents of the Shipping Container Small Box Main Saw Container 1 1 1 1 1 The small box consists of the following items: Table Saw (A) Switch (B) Table Insert (C) Owner's Manual (D) Warranty Card (not shown) 1 1 1 1 2 1 1 1 1 Blade Guard Assembly (E) Riving Knife and Pawl Assembly (F) Handwheel and Swivel Handle (G) Lock Knob (H) Large Hook (J) Small Hook (K) Push Stick (L) Miter Gauge Assembly (M) 27mm Arbor Wrench (N) Main Saw Container Extension Tables Two extension tables are packaged in individu
Assembly Motor Cover Referring to Figures 1 and 2: • Tools: 17mm Wrench, 12mm Wrench 1. Remove shipping bracket (A) securing the motor (C) to table. 2. After the shipping bracket has been removed, install the screw (B) back into the motor support bracket. The upper screws will be used to later to hold the extension wing in place. 3. Remove shipping bracket (D) holding switch assembly (E) to table. Do not discard the bracket (D); it will be used to install the switch. Figure 1 4.
Extension Wing Referring to Figures 4 and 5: • • Hardware: (6) 7/16”x1-1/2” Hex Cap Bolts, (6) 7/16” Lock Washers, (6) 7/16” Flat Washers & (2) Extension Wings Tools: 17mm Wrench, Straight Edge 1. Attach the left extension wing (A) to the table (B) with three each hex cap screws (E), lock washers (F) and flat washers (G). Snug so the extension wing can still be manually adjusted but do not tighten. 2.
Riving Knife and Guard Installation Description Referring to Figure 7: The complete riving knife and guard assembly is shown in A. Before installing onto the saw, the antikickback pawl (E) must be separated from the riving knife (H) as follows: 1. Press and hold the quick-release button (D) on the base of the anti-kickback pawl (E) and lift the pawl to remove from the riving knife (H). Installation Referring to Figure 8: 2.
Electrical Connections Mounting Rails & Extension Table With the extension wings properly aligned, the rail and fence assembly can now be mounted to the saw. Refer to the XACTA® Fence II Commercial 30/50 Owner's Manual (Part No. M-708950Z) for mounting instructions for the rails, fence and optional wooden extension table.
Adjustments Handwheel Adjustments Referring to Figure 10: The front handwheel (B) controls the raising and lowering of the blade (blade height). The side handwheel (D) controls the blade tilt. The blade can be adjusted for a tilt between 90º (vertical or a setting of 0º on the scale) and 45º left tilt (D). Blade height 1. Loosen the lock knob (A) on the front handwheel (B). 2. Turn the handwheel (B) clockwise to raise and counterclockwise to lower the blade. Figure 10 3. Tighten the lock knob (A).
Riving Knife Adjustment Lateral alignment The saw blade and riving knife must be in line as close as possible with each other (lateral alignment) for the prevention of kickback. Upon initial blade guard and riving knife installation no further adjustment should be necessary. Alignment should be checked and adjusted, if required, after each blade change. Check the alignment as follows: 1. Remove the blade guard and pawl (C, E, Fig. 7). Figure 13 2. Place a straightedge (A, Fig.
Blade Alignment • Tools: marker 8mm hex wrench, combination square, Blade alignment with the table is adjusted at the factory. After a period of use, or, after moving the saw to another location, the blade may no longer be aligned with the table. To check and align the blade (refer to Figure 16): 1. Disconnect the saw from the power source. 2. Raise the blade guard up a way from the blade. Figure 16 3.
5. If blade is not at 90 degrees, open the motor cover door, loosen lock nut (A, Fig. 19) and turn adjusting stop screw (B, Fig. 19) on the front trunnion in, or out. The adjusting stop screw should stop against the front trunnion bracket when the blade is 90° to the table. 6. Tighten the lock nut (A, Fig. 19). 7. Set the blade at 45 degrees to the table by turning the blade tilting handwheel counterclockwise as far as it will go. Place a combination square on the table against the blade.
Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Cleaning Lubrication Note: The following maintenance schedule assumes the saw is being used every day. Grease the tilting worm gear, raising worm gear, castor system worm gear and the trunnion areas with a good grade nonhardening grease. Check all adjustments after lubricating. Daily: Wipe down the table surface and grooves with a rust preventive.
Troubleshooting Trouble Possible Cause Solution Overload tripped Saw stops or will not start Saw unplugged from wall or motor Fuse blown or circuit breaker tripped Cord damaged Stops not adjusted correctly Allow motor to cool and reset by pushing off switch Check all plug connections Replace fuse or reset circuit breaker Replace cord Miter gauge out of adjustment Check blade with square and adjust stops Check blade with square and adjust pointer Adjust miter gauge Material binds blade when ripping
Optional Accessories Stock No Description 708295 Tenoning Jig for 10” saws only: 708097 Dado Insert 708118 Universal Mobile Base Parts Ordering Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Table & Cabinet Parts List Index No. Part No. Description Size Qty 1............... JTAS10-1.................Lock Knob ............................................................................................. 1 2............... JTAS10-2.................Miter Gauge Body.................................................................................. 1 3............... TS-1540031 .............Hex Nut ..............................................................M5 .............................. 3 4..
47 ............. TS-0210011 .............Socket Head Cap Screw.....................................7/16-14x3/4 ................ 4 48 ............. TS-0680011 .............Flat Washer ........................................................3/16 ............................ 2 49 ............. JTAS10L-49WN .......Lower Panel .......................................................................................... 1 50 ............. JTAS10L-50N ..........Dust Hose Adapter ......................................
1 2 12 ( 6 ) 8 ( 3) 9 13 3 ( 3) 10 4 5 11 13A (optional) 6 14 7 15 ( 2 ) 28 ( 4 ) 18 ( 6 ) 19 ( 6 ) 20 (6) 61 49 28(2) 60(6) 20 (4) 43 45 47 ( 4 ) 29 44 28(4) 30 34 50 36 59 58(6) 40 41 40 39 35 42 63 66(2) 65(2) 64(2) 22 62 38 56(6) 55(2) 57(6)
Trunnion & Motor Parts List Index No. Part No. Description Size Qty 101 ........... JTAS10L-101 ...........Arbor Nut ............................................................................................... 1 102 ........... JTAS10-102 .............Arbor Flange ......................................................................................... 1 104 ........... JTAS10L-104N ........Arbor with Flange .................................................................................. 1 105 ....
Trunnion & Motor Parts List Index No. Part No. Description Size Qty 149 ........... TS-0208041 .............Socket Head Cap Screw.....................................5/16-18x3/4” ............... 4 150 ........... JTAS10L-150N ........Dust Deflector........................................................................................ 1 151 ........... JTAS10L-151N ........Hose Clamp .......................................................................................... 2 152 ...........
Trunnion & Motor Assembly Drawing 25
Blade Guard Parts and Assembly Index No. Part No. Description Size Qty 1............... JTAS10L-301 ...........Riving Knife .......................................................................................... 1 ................. JTAS10DX-BGA ......Blade Guard Assembly (Index #2 thru #16, #21, #22) ............................ 1 2............... PM2000-302 ............Bushing ................................................................................................. 2 3...............
Wiring Diagrams 3HP/5HP, 230V, 1Phase 27
5HP, 230V, 3 Phase 28
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, TN 37086 Phone: 800-274-6848 www.waltermeier.
