This .pdf document is bookmarked Operating Instructions and Parts Manual DC-1200VX Series Dust Collectors Now with DC-1200VX with Bag Filter Kit WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com DC-1200VX with Canister Kit Part No. M-710701 Revision A1 07/2013 Copyright © 2013 Walter Meier (Manufacturing), Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools.
Table of Contents Warranty and Service...................................................................................................................................... 2 Table of Contents............................................................................................................................................ 3 Warnings ........................................................................................................................................................
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector. 23.
Specifications Main Dust Collection Kits Model Numbers Stock Numbers DC-1200VX-BK1 (Single Phase, with 30 Micron Bag Filter Kit) ............... ...................................... 710701K DC-1200VX-BK3 (Three Phase, with 30 Micron Bag Filter Kit)................ ...................................... 710703K DC-1200VX-CK1 (Single Phase, with Canister Filter Kit) ........................ ...................................... 710702K DC-1200VX-CK3 (Three Phase, with Canister Filter Kit) .................
Unpacking Shipping Content The table below lists the shipping cartons that are included with the various models of the DC-1200 Dust Collector. Base Units (SN 710701 and 710703) 1 – Housing (A) 2 – Hose Clamps (B) 1 – Hose (C) 1 – Impeller (Motor/Fan Assembly) (D) 1 – Inlet Port (E) 1 – Impeller Cover (F) 3 – Support Legs (G) 1 – Base (H) 4 – Casters (J) 1 – Owner's Manual (not shown) 1 – Warranty Card (not shown) 1 – Hardware Bag Base Assly. (SN DC1100-HP) 1 – Hardware Bag, Cone Assly.
Canister Filter Kit 30 Micron Bag Filter Kit (SN 708639B) (SN 708636F) 1 – Handle (O) 1 – Canister Filter (P) 1 – Snap Ring (Q) 5 – Collector Bags (R) 1 – Canister Filter Hardware Bag (SN DC1100-CHP) Contains: (2) M10 Hex Nuts (S) (2) M10 Flat Washers (T) (1) M10 Lock Washer (U) (4) Knobs (V) 1 – Upper Bag Hanger (Y) 1 – Hanger Bracket (Z) 1 – Collector Bag (X) 1 – Filter Bag (W) 1 – Retainer Strap (AA) 30 Micron Bag Filter Kit Contents 5 Micron Bag Filter Kit (Optional) (SN 708636MF) 1 – Upper Bag
Base Unit Assembly Base 1. Install four casters to the under side of the base as pictured in Fig. 2. Referring to Figure 1: 2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B) against the base with a 14mm wrench. This will give the caster proper clearance. Figure 1 Motor and Fan Assembly Referring to Figure 2: 3.
6. Install the housing (A, Fig. 5) to two support legs (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. Note: For models DC-1200VX-BK1 or DC1200VX-BK3 only – Before attaching third support bracket, place the hanger bracket (D, Fig.5) between the support bracket and the housing. 7. Tighten all nuts and bolts at this time with a 13mm wrench. Figure 5 Cone Assembly Referring to Figure 6: 8.
Filter Bag Kit Assembly If you purchased Model DC-1200VX-BK1 or DC1200VX-BK3 Dust Collector, this section describes the assembly and installation of the contents of the 30 Micron Filter Bag Kit (SN 708636F). These instructions also apply to the optional 5 Micron Filter Bag Kit (SN 708636MF). Filter Bag Installation Referring to Figure 8: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3.
Canister Kit Assembly If you purchased Model DC-1200VX-CK1 or DC1200VX-CK3 Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708636F). Canister Filter 1. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 10). 2. Mount the canister filter on top of the collector housing (A, Fig. 5) and tighten the knobs on the canister filter (Figure 10). Figure 10 Collector Bag 3.
Electrical Connections Dust Collector RF Remote Power Control (optional) All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in serious injury! The DC-RC230 Remote Power Control (Figure 14) should be used for activating Dust Collection units powered by 230V only up to 3HP, 1 Phase.
Changing Operating Frequency To mount the DC-RC230 Remote Power Control (refer to Figure 16): If several devices are controlled by the same type remote control unit, each remote control unit can be set to operate at its' own unique operating frequency as follows: Note: Mounting hardware is not included and must be supplied by the machine’s owner or user. 1. Place RC Power Control Unit (A) on the open clearing of the base (B) of the dust collector near the motor (C). Referring to Figure 15: 1.
Maintenance Cleaning the Canister Filter – DC-1200VXCK1 and DC-1200VX-CK3 Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Clean both the filter and collector bags frequently to keep the collector's performance at its optimum.
Parts Breakdown for the DC-1200VX Dust Collector 16
Ordering Replacement Parts To order parts or reach our service department, call 800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts List for the DC-1200VX Dust Collector Index No. Part No. Description Size Qty 1 ...............411035W ................. Impeller Housing ................................................ ......
Index No. Part No. Description Size Qty 52 .............TS-1482021 ............ Hex Head Bolt ................................................... M6x12..................................... 4 53 .............TS-2311061 ............ Hex Nut.............................................................. M6 .......................................... 4 .................DC1200A-NP........... Name Plate (not shown) ..................................... ............................................... 1 .........
Canister Filter Kit (708639B) Index No. Part No. Description Size Qty .................708639B .................. Canister Filter Kit (index #1-24) .......................... ................................................. 1 ...............331050 .................... Handle ............................................................... ............................................... 1 2 ...............TS-1540071 ............ Hex Nut.............................................................. M10 ......
30 Micron Filter Bag Kit (708636F) Index No. Part No. Description Size Qty .................708636F .................. 30 Micron Filter Bag Kit (index #1-5) .................. ................................................. 1 ...............708698 .................... Filter Bag ........................................................... 30 Micron Bag......................... 1 2 ...............AB410012 ............... Retainer Strap.................................................... ................
5-Micron Filter Bag Kit (708636MF) Optional Accessory Index No. Part No. Description Size Qty ................. 708636MF ............... 5-Micron Filter and Collection Bag Kit (index # 1-6) .............................................. 1 ............... 708706 .................... Filter Bag .......................................................... 5 Micron ................................. 1 2 ............... AB410012 ............... Retainer Strap ...................................................
Wiring Diagram For 3 Phase 230/460V Dust Collector (DC-1200VX) Wiring Diagram For Single Phase 230V Only Dust Collector (DC-1200VX) 22
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com www.waltermeier.