Use and Care Manual
Table Of Contents
- 22” and 25” Open-End Drum Sanders
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 About this manual
- 3.0 Table of contents
- 4.0 Specifications
- 5.0 Features and Terminology
- 6.0 Setup and assembly
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 User-maintenance
- 11.0 Tracker kit
- 12.0 Abrasives
- 13.0 Troubleshooting JWDS-2244,-2550 Drum Sanders
- 14.0 Optional accessories
- 15.0 Replacement Parts
- 15.1.1 JWDS-2244/-2550 Head Assembly – Exploded View
- 15.1.2 JWDS-2244 Head Assembly – Parts List
- 15.2.1 JWDS-2244/-2550 Conveyor Table Assembly – Exploded View
- 15.2.2 JWDS-2244 Conveyor Table Assembly – Parts List
- 15.2.3 JWDS-2550 Conveyor Table Assembly – Parts List
- 15.3.1 Open Stand Assembly for JWDS-2244/-2550 – Exploded View
- 15.3.2 723540OS Open Stand Assembly for JWDS-2244 – Parts List
- 15.3.3 (OPTIONAL) 723550OS Open Stand Assembly for JWDS-2550 – Parts List
- 15.4.1 (OPTIONAL) Infeed/Outfeed Tables for JWDS-2244/-2550 – Exploded View
- 15.4.2 (OPTIONAL) 723541 Infeed/Outfeed Tables for JWDS-2244 – Parts List
- 15.4.3 (OPTIONAL) 723551 Infeed/Outfeed Tables for JWDS-2550 – Parts List
- 15.5.1 (OPTIONAL) Digital Readout for JWDS-2244/-2550 – Exploded View
- 15.5.2 (OPTIONAL) Digital Readout for JWDS-2244/-2550 – Parts List
- 15.6.1 Depth Stop Assembly for JWDS-2244/-2550 * – Exploded View
- 15.6.2 Depth Stop Assembly for JWDS-2244/-2550 * – Parts List
- 15.7.1 (OPTIONAL) Closed Stand Assembly for JWDS-2550 – Exploded View
- 15.7.2 (OPTIONAL) Closed Stand Assembly for JWDS-2550 – Parts List
- 16.0 Electrical Connections for JWDS-2244/-2550
- 17.0 Warranty and service
10
Figure 6-3: Assembly of Sander and OPTIONAL Infeed/Outfeed Tables
6.3 Assembling stand
An open stand is provided standard with the JWDS-
2244 Sander. An open or closed stand is available
as an optional accessory (separate purchase) for
the JWDS-2550 Sander. Refer to the assembly
instructions that accompany the stand.
6.4 Mounting sander to stand
The closed stand (for JWDS-2550) is oriented so
that storage door is located at back of machine.
Front/back orientation is not important on the open
stand.
Use an assistant to help lift and
position sander atop stand.
1. Remove any screws holding sander to pallet,
and lift sander from crate.
2. Position sander atop stand so that six threaded
holes of base align with holes in stand rails.
Insert provided screws and washers and tighten
securely.
6.5 Handle and hose hanger
See Figure 6-3.
1. Install height adjustment handle (B) onto
spindle and tighten set screw.
2. Install hose hanger (C) with screws and
washers (C
1
/C
2
).
6.6 Folding infeed/outfeed tables
(OPTIONAL)
See Figure 6-3.
The sander must be bolted to the stand or a work
table when using these table extensions. Maximum
working load of each table is 35 pounds. Fasteners
are provided with the extension tables.
NOTE: If using the folding feature of the
infeed/outfeed tables, make sure your table or
bench allows for such vertical drop at front and back.
To install infeed table:
1. Install front (F) fixed bracket to threaded holes
in sander base with screws and washers
(HP4/5). Make sure bracket is oriented as
shown. Bracket must be flush against base.
NOTE: Long bracket mounts to front
(infeed); short bracket to rear (outfeed).
2. Tighten screws (HP4).
3. Install eccentric cam (HP8) with screw and
washer (HP6/7). Finger tighten only at this time.
4. Install left (G) and right (H) table brackets, using
handles and washers (HP1/2/3).
Note: Handle (HP1) is adjustable – pull up and
rotate on pin to more convenient position, then
release allowing it to settle back onto pin.
5. Place infeed table (D) onto table brackets and
secure with screws and washers (HP4/5).
Finger tighten only.