Instruction Manual

ManualsBrandsJET ManualsStandJET 728200 Flip-Top Stand

Table Of Contents

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-728200

Ph.: 800-274-6848 Edition 2 03/2022

728200 Flip-Top Stand

Instructions and Parts List

IMPORTANT SAFETY INSTRUCTIONS

• Review all instructions before assembling the table.

Improper assembly can cause personal injury and/or

property damage.

• Do not exceed maximum load for the stand.

• Do not stand on this product.

•

WARNING: This product can expose you to

chemicals including lead and cadmium which are

known to the State of California to cause cancer and

birth defects or other reproductive harm. For more

information go to http://www.p65warnings.ca.gov.

Tools required for assembly

10mm and 16mm wrenches

(a manual ratcheting socket wrench will speed

assembly time)

Shipping contents

1 Table Assembly

4 Lower Braces (2 Long, 2 Short)

4 Vertical Legs

4 Adjustment Legs

4 Leveling Pads

1 Instructions and Parts List

1 Product Registration Card

1 Hardware Package (728200-HP)

44 Carriage Bolt M6-1.0x16 – AA

44 Flat Washer 6mm– BB

44 Lock Washers 6mm –CC

44 Hex Nut M6-1.0–DD

Assembly instructions

Use the exploded view and parts list as guides to

assembly. Make all leg and brace fasteners only

finger tight until the entire unit has been assembled.

1. Turn table assembly upside down; use a mat or

piece of cardboard underneath to prevent

scratching.

2. Assemble the four main legs (#20) to the table

brackets (#8/26). Finger tighten only.

3. Determine the height desired, then connect the

adjustment legs (#21) to the main legs. These

can be repositioned later if needed. (It is

recommended that each adjustment leg be

secured by at least 4 screws to the main leg.)

4. Determine placement of lower braces (#24/25)

and assemble them to the main legs/adjustment

legs.

5. Install the leveling foot pads (#22) and tighten

each hex nut (#23) against the adjustment leg. (If

using the optional swivel casters, install those

instead of the pads.)

6. Turn the unit over and push down lightly to make

sure stand rests evenly upon the floor.

7. Fully tighten all fasteners. Take care to not

overtighten.

Holes are provided in the lower braces for attaching a

user-made shelf, not provided.

Summary of content (4 pages)

PAGE 1
728200 Flip-Top Stand Instructions and Parts List • • • • IMPORTANT SAFETY INSTRUCTIONS Review all instructions before assembling the table. Improper assembly can cause personal injury and/or property damage. Do not exceed maximum load for the stand. Do not stand on this product. WARNING: This product can expose you to chemicals including lead and cadmium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.
PAGE 2
see page 4 for operating instructions 728200 Flip-Top Stand – Exploded View 2
PAGE 3
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. 728200 Flip-Top Stand – Parts List Index No. Part No. Description Size Qty 1 ................. TS-1541011 ................ Nylon Lock Hex Nut ..................................................... M5-0.8 ............................. 2 2 .................
PAGE 4
Operation CAUTION: If the optional casters are used, make sure they are locked in place. To tilt table: 1. Pull out left and right handles and rotate them 90degrees to keep them disengaged. 2. Begin tilting front edge of table downward until it just clears the handle pins, then turn handles 90degrees and allow them to slide back in. 3. Continue to tilt table slowly, while helping stabilize the machine(s), until table passes the beveled pins at the rear and snaps into level position.