This .pdf document is bookmarked Operating Instructions and Parts Manual Portable Plate Beveling Machine Models JB-10P, JB-10R JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
Personal safety • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. • Use personal protective equipment. Always wear eye protection.
• • • • • 1.2 Specific safety warnings for plate beveling machine Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation.
2.0 Table of contents Section Page 1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2 1.1 General power tool safety warnings .............................................................................................................. 2 1.2 Specific safety warnings for plate beveling machine .................................................................................. 3 2.0 Table of contents ....................
4.
4.1 Chamfering capacities a 45° 30° 15° X 7 mm (0.28 in.) 3.3 mm (0.13 in.) 1.4 mm (0.06 in.) Y 7 mm (0.28 in.) 5.8 mm (0.23 in.) 5.2 mm (0.20 in.) b 5 mm (0.19 in.) 2.9 mm (0.11 in.) 1.3 mm (0.05 in.) Figure 4-1: chamfering capacity (straight blade inserts) w = chamfer width. Maximum chamfer width (w) is attainable at 45-deg.
6.1 GROUNDING INSTRUCTIONS 5.0 Setup and assembly 1. All Grounded, Cord-connected Tools: 5.1 Shipping contents This machine must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
6.2 Extension cords The use of extension cords is discouraged. Try to position machines within reach of the power source. If an extension cord must be used, make sure it is heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 2 shows correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
8.0 Operations Do not turn ON machine while cutterhead is engaging workpiece. Position machine so that cutter blades can be introduced gradually into workpiece. 8.1 On/off switch Switch has removable safety key to prevent unauthorized use of machine (Figure 8-1). Move switch to OFF and pull out key; store key in safe place. Key must be reinserted to start machine. 8.3 Fixed position 1. Unplug machine from power source. 2.
Figure 8-4: push plate Figure 9-1: blade insert rotation/replacement 9.0 User-maintenance 9.2 Cutterhead replacement If cutterhead replacement is needed: Always disconnect power to machine (unplug) before doing maintenance. Failure to do this may result in serious personal injury. After each use, clean chips and shavings from the machine. Use brush or vacuum, not bare hands. Apply light coat of oil to exposed metal areas, such as guide plates and cutterhead, to inhibit rust.
10.0 Troubleshooting JB-10P, JB-10R Symptom Possible Cause Correction * Motor will not start Safety key removed from switch. Insert safety key to start machine. Low voltage. Check power line for proper voltage. Open circuit in motor or loose connection. Motor will not start: fuses Short circuit in line cord or plug. or circuit breakers blow. Short circuit in motor or loose connections. Incorrect fuses or circuit breakers in power line. Motor overheats, Motor overloaded.
11.1.
11.1.2 JB-10P Portable Plate Beveling Machine – Parts List Index No Part No Description Size Qty 1 ............... JB-10P-01 ................ Pedestal .................................................................. ...................................... 1 2 ............... JB-10P-02 ................. Depth Adjust Nut .................................................... ...................................... 1 3 ............... JB-10P-03 ................. Cutter Guard .................................
Index No Part No Description Size Qty 46 ............. JB-10P-46 ................. Push Plate .............................................................. ...................................... 1 .................. LM000324 ................. Warning Label, JB-10P (not shown) ........................ 50x70mm ...................... 2 .................. LM000325 ................. ID Label, JB-10P (not shown) .................................. ...................................... 1 ..................
11.2.
11.2.2 JB-10R Portable Plate Beveling Machine – Parts List Index No Part No Description Size Qty 1 ............... JB-10R-01 ................. Pedestal ................................................................... ...................................... 1 2 ............... JB-10R-02 ................. Depth Adjust Nut ..................................................... ...................................... 1 3 ............... JB-10R-03 ................. Cutter Cover ..............................
Index No Part No Description Size Qty 50 ............. TS-1490021 .............. Hex Cap Screw ........................................................ M8-1.25x16 ................... 1 .................. LM000329 ................. Warning Label, JB-10R (not shown) ........................ 60x35mm ...................... 2 .................. LM000326 ................. ID Label, JB-10R (not shown).................................. ...................................... 1 .................. JET-92..........
12.
13.0 Warranty and Service JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
