.JET EQUIPMENT & TOOLS OWNER'S MANUAL SBR-30N 1-40N Shear, Brake, and Roll ~ .~ ..ar............. Ifill.,T .-' -'" --' -.-. ,j,J ..'-" ,.,./1";'1" ~ . JET EQUIPMENT & TOOLS, INC. A WMH - Walter Meier Holding Company (SBR-30N shown) P.o. BOX1349 Auburn, WA98071-1349 253-351-6000 Fax 253-939-8001 No.
Important Information 1-YEAR JET offers a one-year limited warranty on this product LIMITED WARRANTY REPLACEMENT PARTS Replacement parts for this tool are available directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box.
& WARNING . . . . Read and understand the entire instruction manual before attempting assembly or operation. This shear, brake, and roll is designed and intended for use by properly trained and experienced personnel only. Ifyou are not familiar with the proper and safe operation of a shear, brake, and roll, do not use until proper training and knowledge have been obtained. This shear, brake, and rollis intended to be used by one person only.
SBR-30N Specifications: Stock Number Capacity (Mild Steel): Shearing Bending Rolling Size of Slip Roll Width of Upper Dies 754031 20 Ga.x30" .. 20 Ga.x30" 20 Ga.x30" 1-1/2"Wx30"L ' Upper Die Height ..'" Minimum Forming Radius ... Weight " ... ' ... ... (approx.) ... 42-1/2"Lx21-1/2"Wx28"H ""'''''''''''' 330 Ibs. SBR-40N Specifications: Stock Number.......................... Capacity (Mild Steel): Shearing..
Assembly 1. Finish removing the crate from around the machine. 2. Remove the bolts holding the machine to the skid. A 3. Carefully clean all rust protected surfaces with a mild solvent or kerosene and a soft rag. Do not use lacquer thinner, paint thinner, or gasoline. These will damage painted surfaces. 4. Coat all machined surfaces with a very light film of oil to inhibit rust. t 5. Carefully move the shear, brake, and roll to a work bench or stand.
Setting Up the Press Brake ateriallarger than 30" (40") 20 Failure to comply may cause e to the machine! To set up for bending: 1. Place a piece of wood 30" long on the bottom die. This will support the upper die(s) during the following adjustment. 2. Close the brake until the wood contacts the upper dies. 3. 4. Loosen hex cap socket retaining screws (A, Fig. 4). Select die(s) (8, Fig. 4) for the desired job and remove others. 5.
2. Work to be sheared must be squared against the squaring guide. 3. Adjust the hold down to within 1/4" above the table when the shear blade is in the up position by turning two hex cap bolts (A, Fig. 7). When the blade starts it's downward travel, the hold down should immediately hold the work piece in place. To prevent distortion, "snap" the handle to facilitate piercing when notching. To adjust lower shear: 1. Loosen two hex cap screws (8, Fig. 7) on each end of the table. 2.
Upper roll must havesufficient pressure on the work piece to feed properly. To remove cylindrical shaped workpieces: 1. Loosen wing screws (A, Fig. 9) on either of the top roll. 2. Loosen hex socket cap screw (8, Fig. 9) and rotate toward the rear of the machine to release roll catch. 3. Carefully grasp roll and pull toward you to remove. 4. Once removed, cylindrical shaped work pieces may be slipped off the end of the roll. Fig.
Breakdown for the SBR-30N Shear, Brake, and Roll g; ,..., ""' ~ "'"' ""'" \ /IV \ Q ,.~~ ;:R. ;;e ;;;:"'
PartsList ForThe SBR-30NShear,Brake,and Roll Index No. Part No.
43 SBR30N-43 44 TS-1482031 45 TS-150506 46 ..SBR30N-46 ..., 47 TS-1492051 48 TS-1492051 49 SBR30N-46 50 SBR30N-50 51 TS-1492041 52 TS-1491051 53 TS-1483031 54 TS-1491031 55 SBR30N-46 56 SBR30N-56 57 TS-1482021 58 ... TS-1482021 59 TS-1482021 60 TS-1491031 61 SBR30N-61 62 63 64 SBR30N-62 SBR30N-63 SBR30N-64 , Thumb Screw Hex Cap Bolt Hex Socket Cap Screw Washer ...... Hex Cap BoiL ... Hex Cap BoiL .
Breakdown for the SBR-40N Shear, Brake, and Roll :S! ~~ ~ ,~~ ::\ '''r \, i", .
Parts List For The SBR-40N Shear, Brake, and Roll Index No. Part No.
39A 40 41 42 43 44 45 46 47 48 49 50.. 51 52 53 54 55 56 57 58 59 60 61.. 62 63 64 SBR40N-3 9A SBR40N-40 SBR40N-41 SBR40N-42 SBR40N-43 SBR40N-44 SBR40N-45 SBR40N-46 SBR40N-47 SBR40N-48 SBR40N-49 SBR40N-50 SBR40N-51 SBR40N-52 SBR40N-53 SBR40N-54 SBR40N- 55 SBR40N-56 SBR40N-57 SBR40N-58 SBR40N-59 SBR40N-60 SBR40N- 61 SBR40N-62 SBR40N- 63. ... SBR40N- 64 Lock Bolt Hex Cap BoiL Set Screw Key Hex Cap BoiL Hex Cap Bolt Hex Socket Cap . Washer Hex Cap BoiL Hex Cap Bolt .