This .pdf document is bookmarked Operating Instructions and Parts Manual 16-Gauge Foot-Operated Corner Notcher Model FN-16 JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 13. Use the right tool. Do not force a tool or attachment to do a job for which it was not designed. 1.0 IMPORTANT SAFETY INSTRUCTIONS 14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before operating. WARNING – To reduce risk of injury: 1. 2.
1. Do not cut round or bar stock on this machine, as it may damage the knives. 32. Use only JET factory authorized replacement parts and accessories; otherwise, the warranty and guarantee are null and void. Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage. This means that if precautions are not heeded, it may result in serious, or possibly even fatal, injury. 2.
.0 Specifications Model number Stock number Capacities Maximum cutting thickness, mild steel Notching angle Maximum notching capacity Stroke length Blade length Main materials Cutting head Blades Table Stand and foot pedal Dimensions Table size LxW Table height from floor T-slot size WxD Overall dimensions LxWxH Shipping dimensions LxWxH Weights Net weight Shipping weight FN-16 755017 16 gauge – 1.5 mm (1/16 in.) 90-degree fixed 80 x 80 mm (3.15 x 3.15 in.) 25 mm (1 in.) 80 mm (3 in.
Read and understand the entire contents of this manual before attempting setup or operation. Failure to comply may cause serious injury. 5.0 Setup The FN-16 Notcher is shipped fully assembled. The user will be required only to secure it to floor and ensure it is properly adjusted and lubricated before operating. 5.1 Shipping contents 1 3 1 1 1 Notcher Hex wrenches, 6,8,10 mm Open-end wrench, 13/16 mm Operating instructions and parts manual Product registration card 5.2 Unpacking and locating 1.
5. Slightly loosen screws (C, Figure 6-2). 6. Loosen nuts on four adjustment screws (G, Figure 6-2) and turn adjustment screws as needed to adjust gap between lower and upper blades on both sides of table. Feeler gauge should be snug but still able to be smoothly removed. 7. Should future adjustment be needed, loosen hex nut and turn stop bolt (D, Figure 6-1) as needed. Retighten hex nut against block to secure setting.
8.2 Additional servicing Maintain sharp blades. If they become dull, resharpen or replace. NOTE: The two lower blades are double-edged; if one edge becomes dull, remove blade from table and flip it end-for-end for a fresh edge. See Figure 6-3 for identification of the cutting edges. Any additional servicing should be performed by authorized service personnel. 9.0 Troubleshooting FN-16 Corner Notcher Symptom Possible Cause Correction Machine cuts with difficulty Machine capacity exceeded.
10.1.
10.1.2 FN-16 Corner Notcher – Parts List Index No Part No Description Size Qty 1 ................ TS-1503051 .............. Socket HD Cap Screw ............................................. M6-1.0x20 ..................... 4 2 ................ TS-1550041 .............. Flat Washer ............................................................. M6 ................................. 4 3 ................ FN16-3 ...................... Top Plate ................................................................. .
11.0 Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.