Operating Instructions and Parts Manual 45-inch English Wheel Model: WH-45T WALTER MEIER (Manufacturing), Inc. 427 New Sanford Road LaVergne, Tennessee 30786 Ph.: 800-274-6848 www.waltermeier.com Part No. M-756151 Revision A 06/2011 Copyright © 2011 Walter Meier (Manufacturing), Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET ® tools.
Table of Contents Warranty and Service..........................................................................................................................2 Table of Contents ...............................................................................................................................3 Warnings............................................................................................................................................4 Introduction ........................................
Warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. This English wheel is designed and intended for use by properly trained and experienced personnel only.
20. Use the right tool at the correct feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 21. Use recommended accessories; improper accessories may be hazardous. 22. Maintain tools with care. Keep wheels clean for best performance. Follow instructions for lubricating and changing accessories. 23. Use leather gloves when handling steel work pieces. 24. Do not stand on the machine.
Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for the JET WH-45T English Wheel. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual.
Securing to Floor Unpacking and Setup Mounting the machine to the floor is strongly recommended (floor mounting hardware is not included). Lag shield anchors with lag bolts and anchor studs are recommended for anchoring to a concrete floor. Research mounting methods and choose one that best fits your application. Cleanup Exposed metal surfaces, including upper and lower wheels, are coated with a protectant to resist corrosion during shipment.
(G) rests against the bottom of the lower wheel bracket (H). Basic Operations 1. Clean the workpiece and wheels thoroughly, removing any grit or abrasive particles. NOTE: Grit or dirt can mar the workpiece and even damage the wheels. Pinch Hazard! Do not place fingers in wheel path during operation. De-burr sharp metal edges and wear leather gloves while handling sheet metal, to prevent injury to your hands. Sharp metal edges can cause lacerations.
2. Flip up the latch (J) and slide out the upper wheel axle (K) while holding the wheel. Figure 5 To rotate lower wheel: Refer to Figure 6. 1. Disengage quick release lever (F). 2. Remove lower clearance. wheel if needed for 3. Lift the lower wheel assembly until the knurled screw (L) reaches the top of the groove in which it is currently positioned (L1). Figure 4 3. Carefully remove the upper wheel (D) and set it on a bracket on the upper wheel rack. 4. Place a new upper wheel into position.
To rotate upper wheel: Adjusting the Quick Release Lever Refer to Figure 7. Refer to Figure 8: 6. Remove the lower wheel to provide clearance for the following steps. The quick release lever is adjusted at the factory. However, it may have become loose during shipping. The set screws must engage the lever to prevent it from slipping. 7. Turn the upper wheel knob (A) counterclockwise to lower the upper wheel bracket (B) below the frame block (C). To adjust the quick release lever: 8.
Apply a coating of lithium grease to the cams (E) where they contact the bottom of the lower wheel bracket. Pivot Points Apply a small amount of oil, such as SAE 30W, to the pivot points (F). Wheels When upper or lower wheels are not being used, or are stored away, apply a light coat of oil to prevent rust. Wipe off the oil before using the wheels.
Troubleshooting the WH-45T English Wheel Trouble Probable Cause Remedy Lower wheel bracket and cams are binding. Lubricate contact points between top of cams and bracket. Setscrews on cams loose, not contacting quick release lever flats. Align setscrews with lever flats and tighten. Upper wheel not secured to frame bracket. Turn upper wheel knob clockwise until upper wheel bracket is snug against frame bracket. Workpiece too thick. Use sheet metal of appropriate thickness. Crown is too low.
Assembly Drawing for WH-45T English Wheel 13
Parts List for WH-45T English Wheel Index No. Part No. Description Size Qty 1 .............. WH45T-1 ................Frame ................................................................................................ 1 1-1 ........... WH45T-1-1..............Post Clamp ........................................................................................ 2 1-2 ........... WH45T-1-2..............Frame Support Stand .......................................................................... 1 2 .......
Parts List for WH-45T English Wheel Index No. Part No. Description Size Qty 41 ............ WH45-41 .................Snap Ring ........................................................Ø20 ........................... 1 42 ............ TS-1522031 ............Socket Set Screw .............................................M5x10........................ 1 46 ............ TS-1523021 ............Socket Set Screw .............................................M6x8 ......................... 1 47 ............
Wheel Chart Index No. Wheel Description Spec Index No.
