Operating Instructions and Parts Manual 45-inch English Wheel Model: WH-45T JET 427 New Sanford Road LaVergne, Tennessee 30786 Ph.: 800-274-6848 www.jettools.com Part No.
11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication. 12. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before using. 1.0 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: 13. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately. 1.
26. Do not stand on the machine. Serious injury could occur if the machine tips over. 27. Remove loose items and unnecessary work pieces from the area before using the machine. Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage. This means that if precautions are not heeded, it may result in serious injury or possibly even death. 2.0 Table of Contents 1.
3.0 About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for the JET WH-45T English Wheel. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this manual.
Read and understand all assembly instructions before attempting assembly. Use an assistant when any heavy lifting is required. Failure to comply may cause serious injury. 5.0 Setup and assembly 5.1 Shipping contents 1 10 4 1 1 English wheel Lower wheel assemblies Upper wheel assemblies Operating instructions and parts manual Product registration card Figure 5-1 6.0 Adjustments 5.2 Tools required for assembly 6.
.1.2 Lower wheel 1. Release cam lever (D, Figure 6-1) and remove lower wheel (E). If needed, use adjusting wheel (see F, Figure 8-1) to lower post further for additional clearance. 2. Position new wheel in groove and engage cam lever. 3. Raise lower wheel assembly using adjusting wheel (F, Figure 8-1). 6.2 Wheel orientation Upper and lower wheel housings can be rotated 90-degrees to accommodate different sizes of material, and prevent material from contacting machine frame while being worked.
. To remove and re-insert same-gauge material, simply engage or disengage cam lever. 8.0 User-maintenance 8.1 Lubrication Refer to Figure 8-1. Periodically apply grease to contact surfaces of upper and lower wheel housings (G1), cams (G2), and adjusting wheel leadscrew (G3). Periodically apply a light machine oil to upper wheel shaft (O1), lower wheel post (O2), adjusting nut (O3), and position block pivot area (O4). Also apply light coat of oil to wheels before storing them, to inhibit rust.
11.0 Troubleshooting WH-45T English Wheel Table 1 Trouble Probable Cause Remedy Pressing workpiece too lightly. Raise lower wheel for better contact. Improper wheel selection. Use proper wheel combination. Make sure lower wheel has appropriate crown. Sheet metal too thick. Select material within machine capacity. Roll marks or marring of material. Pressure too tight against workpiece. Use minimal pressure of wheels against workpiece.
12.
12.2 WH-45T English Wheel – Parts List Index No. Part No. Description Size Qty 1 ............... WH45T-1G ............... Frame ................................................................... .................................... 1 1-1 ............ WH45T-1-1G............ Post Clamp........................................................... .................................... 2 1-2 ............ WH45T-1-2G............ Frame Support Stand ........................................... ....................
Index No. Part No. Description Size Qty 41 ............. WH45-41 .................. Snap Ring ............................................................ Ø20 ............................. 1 42 ............. TS-1522031 ............. Socket Set Screw ................................................. M5x10 ......................... 1 46 ............. TS-1523021 ............. Socket Set Screw ................................................. M6x8 ........................... 1 47 ............. TS-1503071 ..
13.0 Wheel Chart Index No. Wheel Description Spec Index No.
14.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
This page intentionally left blank.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
