This .pdf document is bookmarked Operating Instructions and Parts Manual 15-inch Variable Speed Drill Press Models: J-A3816, J-A5816, J- A5818 Model J-A5816 JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Model J-A3816 Part No.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
Table of Contents Warranty and Service .......................................................................................................................................... 2 Table of Contents ................................................................................................................................................ 3 Warnings .............................................................................................................................................................
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. This drill press is designed and intended for use by properly trained and experienced personnel only.
24. Check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. 25. A guard or other part that is damaged should be properly repaired or replaced. 26. Do not leave tool running unattended. Turn power off.
Safety Instructions for Drill Presses 1. All work shall be secured using either clamps or a vise to the drill press table. It is unsafe to use your hands to hold any workpiece being drilled. 6. Always wear protective eye wear when operating, servicing or adjusting machinery. Eyewear shall be impact resistant, protective safety glasses with side shields complying with ANSI Z87.1 specifications. Use of the eye wear which does not comply with ANSI Z87.
Specifications The JET 15-Inch Vari-Speed Drill Presses, Models J-A3816, J-A5816, and J-A5818 provide drilling speeds from 400 to 5,000 rpm. Simple handwheel adjustment sets the speeds with an LED speed display on the faceplate of the machine. JET's 15-inch vari-speed drill press provides a solid base for drilling and offers a wide range of spindle speeds. The large quill provides greater accuracy. The large worktable provides the operator with room to work and ample support for the workpiece.
mounting holes in the base as required to level the drill press. Introduction This manual includes operating and maintenance instructions for the JET 15-Inch Vari-Speed Drill Presses, Models J-A3816, JA5816, and J-A5818. This manual also includes parts listings and illustrations of replaceable parts. Assembly The Drill Press is shipped with the head in lowered position. Follow these instructions to assemble. 1. Figure 2: Loosen locking handle on head and raise the head toward the top of the column.
4. Figure 4: Loosen (do not remove) the four screws in the worm gear housing. Figure 4 5. Figure 5: Place the rack against the column and slide it down as far as it will go into the slot in the table bracket. (Position the rack with the longer flat area toward the top and the short flat area toward the bottom.) Figure 6 Cleaning 6. Figure 5: Slide the rack ring down onto the top of the rack and tighten the set screw on the rack ring. Clean off any protective grease with solvent.
The speed control handwheel is located on the left side of the drill head. An LED speed indicator is provided on the face plate on the drill head. 2. The work table must be locked to the column so it will not be forced down the column. 3. Be sure the belt is tightened to the proper tension. 4. DO NOT start to drill the workpiece until making certain the workpiece is held down securely. 5. BEFORE turning the speed handwheel in either direction. control 6.
too high. A drill chipping or breaking out at the cutting edges indicates that either the feed is too heavy or the drill has been ground with too much tip clearance. 7. Operate the drill press to verify correct operation. Replacement of Motor Speeds for High Speed Steel Drills Make sure to disconnect Material Speed In SFMelec-trical power to the drill press to avoid Alloy Steel — 300 to 400 Brinell ..................... 20 - 30 the possibility of inadvertent operation and Stainless Steel................
Figure 9 – Table Adjustment Head Adjustment Change the radial position of the drill head only if the drill press base is secured to the floor. Swinging the drill head without the base being secured to the floor will cause the drill press to become unstable and tip over resulting in injury and/or damage to the machine. The radial position of the drill head can be changed to accommodate the drilling of a hole that may be offset from the center of the table.
Electrical 230 Volt Operation Referring to Figure 12: 115 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: Referring to Figure 11: As received from the factory, your drill press is ready to run at 115-volt operation. This drill press, when wired for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated in (A).
Grounding Instructions Extension Cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. The table following shows the correct size to use depending on the cord length and name plate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord.
Troubleshooting Problem Spindle does not turn. Spindle noisy. Drill stalls. Probable Cause Suggested Remedy Circuit breaker tripped. Reset circuit breaker. Branch circuit breaker tripped or fuse blown. Reset Open wire in switch circuit. Repair open circuit. Defective switch. Repair switch. Broken drive belt. Replace drive belt. Damaged spindle bearings. Replace bearings. Worn spline. Replace spline. branch circuit breaker/replace fuse. Worn drive belt. Check condition of belt.
Exploded View — Head Models J-A5816 and J-A5818 16
Parts List - Head Models J-A5816 and J-A5818 Item Part No. Description Size Qty. 1............... 5507580...................Chuck (with Key) ................................................................................... 1 2A ............ 5507495...................Arbor ..................................................................#2 MT x JT3 ............... 1 3A ............ 5507496A ................Spindle .......................................................................................
Parts List - Head Models J-A5816 and J-A5818 Item Part No. Description Size Qty. 55 ............. 5041140...................Vaiable Speed Pulley (Spindle).............................................................. 1 55A .......... 5513510...................Hex Nut ................................................................................................ 1 55B .......... 5513511...................Socket Head Cap Screw .......................................................................
Exploded View — Head Model J-A3816 19
Parts List - Head Model J-A3816 Item Part No. Description Size Qty. 1............... 5507580...................Chuck (with Key) ................................................................................... 1 2A ............ 5507495...................Arbor ..................................................................#2 MT x JT3 .............. 1 3A ............ 5507496A ................Spindle Assembly ................................................................................. 1 4.......
Parts List - Head Model J-A3816 Item Part No. Description Size Qty. 64 ............. 9138011...................Self Tapping Screw ............................................#10 x 3/4 Type A ........ 4 69 ............. J-5518168 ................Pulley Cover (w/door & latch)................................................................. 1 70 ............. J-5518169G .............Face Plate ............................................................................................. 1 75 .............
Exploded View – Base Floor Models J-A3816, J-A5816 and J-A5818 22
Parts List – Base Floor Models J-A3816, J-A5816 and J-A5818 Item Part No. Description Size Qty. 1 ............... 1000772 .................. Locknut.............................................................. ................................... 1 2 ............... 5003751 .................. Table Lock (Plain Side) ...................................... ................................... 1 3 ............... J-5507508 ............... Table ..............................................................
Exploded View – Safety Shield Assembly, Models J-A3816, J-A5816 and J-A5818 Parts List – Safety Shield Assembly (All Models) Item Part No. Description Size Qty. ................. 32104A ................... Safety Shield Assembly (For 15” DP) (#1 thru 16) .................................. 1 1 ............... 6293347 .................. Spring Pin .......................................................... 3x16 ........................... 1 2 ............... 32106A-2 ................ Support Bracket Bar.
