Pneumatic Die Grinders #505414, JAT-414 #505417, JAT-417 #505418, JAT-418 JAT-417 JAT-414 JAT-418 Operation Manual M-505414 Edition 1 05/2019 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
IMPORTANT SAFETY INSTRUCTIONS General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
24. Keep visitors a safe distance from the work area. Keep children away. 25. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 26. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 27. Repetitive motions and/or exposure to constant vibration can be harmful to hands and arms.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-414/-417/-418 Pneumatic Die Grinder. This manual contains instructions on safety precautions, and general operating and maintenance procedures. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Tool specifications Model JAT-414 JAT-417 JAT-418 Stock number 505414 505417 505418 Configuration Standard Extended 90° head Collet size 1/4 in. Horsepower 0.5 1/4 in. 0.5 1/4 in. 0.5 Free speed (at 90psi) Air inlet 22,000 RPM 24.85 SCFM / 3.5CFM at 90psi 1/4 in. NPT, swiveling 22,000 RPM 24.85 SCFM / 3.5CFM at 90psi 1/4 in. NPT, swiveling 18,000 RPM 24.85 SCFM / 3.5CFM at 90psi 1/4 in. NPT, swiveling Air hose inside diameter 3/8 in. 3/8 in. 3/8 in.
IMPORTANT: Connecting a quick-change coupling directly to the tool is not recommended, as vibration may cause the connection to fail. Instead, add a leader hose and install any quick-change couplings farther down the line. Setup and Assembly Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. 5.
Storage Rule of Thumb Avoid storing the die grinder in very humid locations which promotes rusting of internal mechanisms. Always oil the tool and disconnect air hose before storage. Air system requirements If it takes more than 8 seconds to tighten or loosen a bolt or nut with an air impact wrench at maximum setting, the air wrench is too small or the air compressor CFM is not powerful enough for the job. Continued use in either capacity will cause damage to the tool. 1.
Figure 2 Recommended arrangement of air piping and air line system 8 JAT-414,-417,-418 Die Grinders
Troubleshooting JAT-414,-417,-418 Die Grinders Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Tool will not start. Possible cause Remedy Air valve closed or obstructed. Open valve; clear any obstructions. Dirt or gum deposits on components. Flush tool with gum solvent. If problem persists, disassemble, clean and lubricate internal parts. Rotor vanes or other components are worn.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. JET products carry a limited warranty which varies in duration based upon the product.
JET 11
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
